If VBA = 240 < 120° VRMS, positive sequence, determine, in the circuit of the attached figure. A) Neutral displacement voltage Vn' B) Reading of wattmeters placed in B and C (common A). 5 j15 N 12 - j12 N B HE j7 N C 10 kVA, fp 0.6*

If VBA = 240 < 120° VRMS, positive sequence, determine, in the circuit of the attached figure. A) Neutral displacement voltage Vn' B) Reading of wattmeters placed in B and C (common A). 5 j15 N 12 - j12 N B HE j7 N C 10 kVA, fp 0.6*

Power System Analysis and Design (MindTap Course List)

6th Edition

ISBN:9781305632134

Author:J. Duncan Glover, Thomas Overbye, Mulukutla S. Sarma

Publisher:J. Duncan Glover, Thomas Overbye, Mulukutla S. Sarma

Chapter2: Fundamentals

Section: Chapter Questions

Problem 2.10P: For the circuit element of Problem 2.3, calculate (a) the instantaneous power absorbed, (b) the real...

See similar textbooks

Related questions

Q: B) (Using Direct method) convert ( 10010001 )BCD to Binary number.

Q: 7- Gray code for (11001);

Q: B) Determine F in Fig.(1). Simplify the Boolean expression us ing Boolean algebra. Redraw the logic ...

Q: Find the voltage of R1 resistor

Q: certain class A power amplifier delivers Vpeak=5V, and Ipeak=2A to a load with an input signal power...

A: Load voltage is given, Load current is given, Therefore, output power to the load is ,

Q: For the circuit in Fig. 10.94, composed of standard values: Determine the time constant of the c...

Q: Explain what carrier mobility is and elaborate on the factors that influence carrier mobility

A: Carrier mobility is defined as the how fast the carrier can move in a semiconductor. Mobility is rep...

Q: Calculate the following about the circuit in Figure 2.1 (If silicon diodes are employed in therectif...

Q: Find the max power transfer to the load resistor RL

A: Given circuit is =

Q: I need it in 45 minutes

Q: Q.5: In a certain conducting region, H = yz(x² + y²) ax – y²xzāy + 4x²y?a, A/m a- Determine J at (5,...

Q: Suggest remedial measures to a facility manager who complains of low voltage at hisfacility.

A: The main causes for the low voltages are, Overloading the supply lines and feeders. Loose connecti...

Q: Luminaire lamp with power (80 w) working at voltage (220 V) working temperature° Fuse to (1500 m(If ...

A: The resistance of the luminaire lamp is determined as:

Q: A 15 MVA, 11 kV, alternator has positive, negative and zero sequence reactance are 0.3 p.u., 0.2 p.u...

A: The positive, negative and the zero sequence reactance with the neutral resistance of the three phas...

Q: 13.37 The double-excited electromechanical system shown in Figure P13.37 moves horizontally. Assume ...

A: The doubly-excited system shown moves horizontally. The cross section of the structure is w X w. Par...

Q: The parameters of a 1000/250V, 50HZ single phase transformer are: R1=1.3 N, X1=2.8 N, R2=0.11 N, X2=...

Q: B) Design BCD to Excess-5 converter, using Karanough-map.

Q: A series circuit of RLC with following parameters, R=15 ohm, L=20 m H & C=100 micro Farad. VT=...

Q: Note Questions True and false

Q: Define all the power related to the ac circuit.

Q: A 80 V rms is stepped down to 18V rms by a transformer. The output from the transformer isrectified ...

Q: How long will it take, in minutes, for a transformer to transfer 2.3 X 106 J of energy from a 120-V ...

A: Write the expression for the power transferred from one source to the other.

Q: Q5: Compute the magnetic field intensity B of a long straight wire that has a circular loop with a r...

A: Hello, since you have posted multiple questions and not specified which question to solve we will so...

Q: In the circuit below, the capacitor voltage just before t=0 is 20 40 12 V 1H v(t} 2 F 1A Select an a...

Q: Q5: For a unity feedback control system with the following feed forward transfer function K G(s) = (...

Q: Calculate each of the circuit parameters for the provided circuit

Q: Briefly explain the construction and operation of a DC Shunt motor.

A: DC Shunt motor Series connection and parallel connection is known as series and shunt respectively. ...

Q: B) Simplify the following Boolean expression, then implement by using NOR gates only. [AB(C+ BD) + A...

Q: Through a source transformation on the following network, determine the current Ix . Given: The resi...

Q: of E1 E2 + E3+ IIn the circuit shown, 4 12 | R1 = 40, R2 = 50, R3 = 6 0, & = 8 V,E2 = 5 V and & = 12...

Q: Inductive reactance, resistance, and impedance are all measured in ohms. What is the common characte...

A: When an electric current flows through a resistive circuit, the current faces an opposition. In othe...

Q: For the circuit shown below, find the range of values for the feedback resistor Rf such that the cir...

A: Given circuit is =

Q: A 400 volts 4 pole 50 Hz three phase star connected induction motor has r-0,x1=x2=1 N, r,=0.42, xm= ...

Q: Q7: Match between column A and column B: Column A 1- Biot-Savart law Column B A- §B. dl = µol B- V²V...

Q: decimal number (- 30 ) as an 8-bit

Q: Find out the power of the signal x(n)=u(n).

A: The power of any discrete-time signal can be computed using the following formula:

Q: Suggest remedial measures to a facility manager who complains of low voltage at his facility.

A: The main causes for the low voltages are, Overloading the supply Loose connection s at the feeders ...

Q: A dc shunt motor drives an elevator load which requires a constant torque of 300 N.m. The motor is...

A: Given values are =

Q: Find the state table for this counter and draw the counter waveforms using .MULTISIM or any applicat...

Q: Answer question A to c

A: Part (a): The rotor of the synchronous generator rotates at the synchronous speed. Thus, the synchro...

Q: 1. Analysis with D Flip- flop. Example : Consider the following equahion Cinput eauation for D flip-...

A: The Boolean expression of D flip-flop is given below: (a) Sequential circuit is shown below: ...

Concept explainers

Power Measurement

According to Blondel's theorem, the total power is measured with one less number of wattmeters than the number of wires present in the system. So, a single-phase and two-wire system will require one wattmeter and a single-phase and the three-wire system will require two wattmeters, and a three-phase and the three-wire system will also require two wattmeters and a three-phase and the four-wire system will require three wattmeter devices. The wattmeter is a device that measures power using one voltage and one current input as shown in the above figure. Multiple current or voltage input pair cables are used by many power analyzers and digital storage oscilloscopes (DSOs) for measuring watts, in effect within a single instrument acting as multiple wattmeters. It is possible to measure three-phase and four-wire power with one correctly specified power analyzer.

Question

If VBA = 240 < 120° VRMS, positive sequence, determine, in the circuit of the attached figure.
A) Neutral displacement voltage Vn'
B) Reading of wattmeters placed in B and C (common A).
5
j15 N
12
- j12 N
B
HE
j7 N
C
10 kVA, fp 0.6*

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

SEE SOLUTION Check out a sample Q&A here

Step 1

Step 2

Step 3

Step 4

Step by step

Solved in 4 steps with 8 images

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, electrical-engineering and related others by exploring similar questions and additional content below.

Similar questions

For the circuit element of Problem 2.3, calculate (a) the instantaneous power absorbed, (b) the real power (state whether it is delivered or absorbed). (c) the reactive power (state whether delivered or absorbed). (d) the power factor (state whether lagging or leading). [Note: By convention the power factor cos() is positive. If | | is greater than 90, then the reference direction for current may be reversed, resulting in a positive value of cos() ].
2. Solve the following problem: A THREE-PHASE PLANT CONSUMES 600 KVA, WITH A VOLTAGE OF 2400 VOLTS AND A POWER FACTOR OF 0.8 BEHIND. a) DETERMINE THE EQUIVALENT DELTA IMPEDANCE OF THE PLANT. b) IF THE PLANT WERE A STAR, CALCULATE THE RESISTANCE, REACTANCE AND THE CORRESPONDING PASSIVE ELEMENT.
A 3- phase star connected load has resistance of 10 Ω, inductance of 15.9mH & a capacitive reactance of 8 Ω respectively in R, B & Y phases. If the voltage between line and neutral line is 231V, 50Hz supply, Assume RYB sequence.Calculate the neutral current and Draw the current & voltage phasors.
A 400-V, 3-phase, 4-wire service mains supplies a star connected load. The resistance of each line is 0.1ohms and that of the neutral 0.2 ohm. The load impedances are Z 1 = (6 + j9) ohms l Z 2 = 8 ohms ; Z 3 = )6 – j8)ohms. Calculate the current in the neutral.e. 56.22 A f. 50.06 A g. 45.18 A h. 49.35 A
Design a power factor correction circuit with the value of parallel capacitance needed tocorrect a load of 179 kVAR at 0.85 lagging pf to unity pf. Assume that the load issupplied by a 110-V (rms), 60-Hz line.
A 210V, 50 Hz, single phase radial distribution system, the resistance of the wire is 0.0008 ohm/m supply and return. Two loads are connected and it consumes 10 and 10 A respectively and are fed from the cable at distance of 15 and 15 respectively. Calculate the voltage available across load 1 and 2
A single-phase circuit is placed across a 120-Vrms, 60-Hz source, with an ammeter, a voltmeter, and awattmeter connected. The instruments indicate 12 A,120 V, and 800W, respectively. Finda. The power factor.b. The phase angle.c. The impedance.d. The resistance.
A three-phase, three-wire, 240 V ACB system supplies power to a wye-connected load with resistances and inductances of Za: 25 ohms, 15mH; Zb: 40 ohms, 10mH; Zc: 20 ohms, 18mH. Find the total average power delivered to the load if the line impedance is given by 2 ohms and 15mH.
A d.c. 3-wire system is to be converted into a 3-phase, 4-wire system by adding a fourth wire equal in X-section to each outer of the d.c system. If the percentage power loss and voltage at the consumer's terminals are to be the same in the two cases, find the extra power at unity power factor that can be supplied by the a.c. system. Assume loads to be balanced.
A 20 kVA, 220 V, wye-connected, 3-phase salient-pole generator supplied load at 0.707 pf lagging. The reactances per phase are Xd = 2 ohms, Xq = 4 ohms and resistance is negligible. Find the %VR at the above load.
q22/ A single phase, 50 Hz, overhead transmission line supplies 1300 kW at 26 kV, 0.65 p.f. lagging. The total resistance and line inductive reactance of the line are 4.75 Ω and 7.75 Ω respectively. Calculate the sending end voltage, voltage regulation, sending end power factor and efficiency of transmission
A single – phase transmission line supplies a reactive load at a lagging power factor. The load draws 1.2 pu current at 0.6 pu voltage while drawing 0.5 pu (true) power. If the base voltage is 20 kV and the base current is 160 A, calculate the power factor and the ohmic value of the resistance of the load.