If we connect an Ohmic resistance R1 and a non-Ohmic resistance R2 > R1 in series in a circuit, which of the following is true? O a. The current in Rj is greater than the current in R2. O b. There is a linear relation between the total resistance and the current in R1. O c. The slope of the total potential difference across the two resistances vs. the current in R1 is R1+ R2. O d. The current in R2 is greater than the current in R1. O e. The potential difference across R2 is greater than the potential difference across R.

If we connect an Ohmic resistance R1 and a non-Ohmic resistance R2 > R1 in series in a circuit, which of the following is true? O a. The current in Rj is greater than the current in R2. O b. There is a linear relation between the total resistance and the current in R1. O c. The slope of the total potential difference across the two resistances vs. the current in R1 is R1+ R2. O d. The current in R2 is greater than the current in R1. O e. The potential difference across R2 is greater than the potential difference across R.

College Physics

10th Edition

ISBN:9781285737027

Author:Raymond A. Serway, Chris Vuille

Publisher:Raymond A. Serway, Chris Vuille

Chapter18: Direct-Current Circuits

Section: Chapter Questions

Problem 10P: Consider the circuit shown in Figure P18.10. (a) Calculate the equivalent resistance of the 10.0-...

See similar textbooks

Similar questions

Consider the circuit shown in Figure P28.21 on page 860. (a) Find the voltage across the 3.00-0 resistor, (b) Find the current in the 3.00-12 resistor.
Consider the circuit shown in Figure P28.9. Find (a) the current in the 20.0- resistor and (b) the potential difference between points a and b.
A 50resistor is connected across the emf v(t)=(160V)sin(120t) . Write an expression for the current throug1 the resistor.
(a) Explain how the mnemonic ELI the ICE man can be used to recall whether current leads voltage or voltage leads current in RLC circuits. Note that E represents emf . (b) Explain how CIVIL works as another mnemonic device, where V represents voltage.
Why is the following situation impossible? A technician is testing a circuit that contains a resistance R. He realizes that a better design for the circuit would include a resistance 73R rather than R. He has three additional resistors, each with resistance R. By combining these additional resistors in a certain combination that is then placed in series with the original resistor, he achieves the desired resistance.
A person with body resistance between his hands of 1.00 k accidentally grasps the terminals of a 20.0-kV power supply. (Do NOT do this!) (a) Draw a circuit diagram to represent the situation. (b) If the internal resistance of the power supply is 2000 , what is the current through his body? (c) What is the power dissipated in his body? (d) If the power supply is to be made safe by increasing its internal resistance, what should the internal resistance be for the maximum current in this situation to be 1.00 mA or less? (e) Will this modification compromise the effectiveness of the power supply for driving low-re si stance devices? Explain your reasoning,
In the circuit of Figure P28.30, determine (a) the current in each resistor and (b) the potential difference across the 200- resistor.
Three identical 60.0-W, 120-V lightbulbs are connected across a 120-V power source as shown in Figure P28.72. Assuming the resistance of each lightbulb is constant (even though in reality the resistance might increase markedly with current), find (a) the total power supplied by the power source and (b) the potential difference across each lightbulb.
In this chapter, most examples and problems involved direct current (DC). DC circuits have the current flowing in one direction, from positive to negative. When the current was changing, it was changed linearly from I=ImaxtoI=+Imax and the voltage changed linearly from V=Vmax to V=+Vmax where Vmax=ImaxR .Suppose a voltage source is placed in series with a resistor of R = 10 that supplied a current that alternated as a sine wave, for example, I(t)=(3.00A)sin(24.00st) . (a) What would a graph of the voltage drop across the resistor V(t) versus time look like? (b) What would a plot of V(t) versus I(t) for one period look like? (Hint: If you are not sure, try plotting V(t) versus I(t) using a spreadsheet.)
Consider the circuit shown in the preceding problem. Write equations for the power supplied by the voltage sources and the power dissipated by the resistors in terms
The circuit in Figure P27.34a consists of three resistors and one battery with no internal resistance. (a) Find the current in the 5.00- resistor. (b) Find the power delivered to the 5.00- resistor. (c) In each of the circuits in Figures P27.34b, P27.34c, and P27.34d, an additional 15.0-V battery has been inserted into the circuit. Which diagram or diagrams represent a circuit that requires the use of Kirchhoffs rules to find the currents? Explain why. (d) In which of these three new circuits is the smallest amount of power delivered to the 10.0- resistor? (You need not calculate the power in each circuit if you explain your answer.) Figure P27.34
Consider the circuit shown in Figure P18.10. (a) Calculate the equivalent resistance of the 10.0- and 5.00- resistors connected in parallel. (b) Using the result of part (a), calculate the combined resistance of the 10.0-, 5.00-, and 4.00- resistors. (c) Calculate the equivalent resistance of the combined resistance found in part (b) and the parallel 3.00- resistor. (d) Combine the equivalent resistance found in part (c) with the 2.00- resistor. (e) Calculate the total current in the circuit. (f) What is the voltage drop across the 2.00- resistor? (g) Subtracting the result of part (f) from the battery voltage, find the voltage across the 3.00- resistor. (h) Calculate the current in the 3.00- resistor. Figure P18.10