II. STEEL 1. Define the Tension test for rebars 2. Enumerate and explain different methods of Testing Steel 3. Complete the table below: Bar Classification Diameter (mm) Gauge Length (mm) Weight (kg) Unit weight of steel is 7850kg/m³ Maximum Load (KN) Area (mm²) Tensile Strength (MPa) Length after Tensile Test (mm) Elongation (mm) Deformed 500 201.0619 414 503.25

II. STEEL 1. Define the Tension test for rebars 2. Enumerate and explain different methods of Testing Steel 3. Complete the table below: Bar Classification Diameter (mm) Gauge Length (mm) Weight (kg) Unit weight of steel is 7850kg/m³ Maximum Load (KN) Area (mm²) Tensile Strength (MPa) Length after Tensile Test (mm) Elongation (mm) Deformed 500 201.0619 414 503.25

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

The rubber band given below is subjected to the following tensile loading. Calculate the minimum thickness of the rubber (tr) and the minimum steel pin diameter (Dpin) so that the structure does not fail. Consider: Allowable tensile strength of the rubber= 20MPa Allowable shear strength of the steel = 200MPa Reflection: 1) How would you solve this problem if a Factor of Safety was given? 2) Are there any other dimensions worth calculating for the rubber belt?
A grade 36 round steel bar with a diameter of 0.5 inches and a gauge length of 2 inches wassubjected to tension to rupture following ASTM E-8 test procedure. The load and deformation data wereas shown in the following table: Using a spreadsheet program obtain the following:a. A plot of the stress-strain relationship. Label the axes and show units.b. A plot of the linear portion of the stress-strain relationship. Determine modulus of elasticity usingthe best fit approach.c. Proportional limit.d. Yield stress.e. Ultimate strength.f. When the applied load was 4.07 kips, the diameter was measured as 0.499905 inches. DeterminePoisson’s ratio.g. After the rod was broken, the two parts were put back together and the diameter of at the neckwas measured as 0.416012 inches. What is the true stress value at fracture? Is the true stress atfracture larger or smaller than the engineering stress at fracture? Why?h. Do you expect the true strain at fracture to be larger or smaller than the…
In the figure below, the wood pole is supported by cables of 0.32-in diameter. The turnbuckles in the cables are tightened until the stress in the cables reaches 60000psi. If the working compressive stress for the wood is 216psi. Determine the smallest permissible diameter of the pole.___________inches in 2 decimal places. Take note: Write it on a paper, hand written showing answer. Thanks
Please refer to the figure shown below. If P is equal to 8200 lb., and if all the rods have a cross-sectional area to be 0.4 sq. in. Explain why the set-up will fail or will not fail if the allowable stresses in Steel is 120MPa; 90MPa in Alumimun; and 100Mpa in Bronze. As the civil engineer of the project, if the set-up fails, provide a recommendation to prevent the failure to occur. Show your solutions to support your recommendation.
Getting measurements from Figure 11.20, determine approximate values ofthe following items for plain concrete, concrete with 2% steel fibers, and concrete with 3% steel fibers:a. Modulus of elasticityb. Ultimate strengthc. Strain at failured. Toughness. Curves may be approximated with a series of straight lines.e. Comment on the effects of increasing the steel fiber content on items a, b,c, and d above.
hree steel bars with a diameter of 25 mm and carbon contents of 0.2, 0.5, and 0.8%, respectively. The specimens were subjected to tension until rupture. The load versus deformation results were as shown in Table P3.19. If the gauge length is 50 mm, determine the following: The tensile stresses and strains for each specimen at each load increment. Plot stresses versus strains for all specimens on one graph. The proportional limit for each specimen. The 0.2% offset yield strength for each specimen. The modulus of elasticity for each specimen. The strain at rupture for each specimen. Comment on the effect of increasing the carbon content on the following: Yield strength ii. Modulus of elasticity iii. Ductility
Show complete process. A tensile load of 150 kN is applied to a round metal bar with a diameter of 16 mm and a gage length of 80 mm. Under this load the bar elastically deforms so that the gage length increases to 80.1192 mm and the diameter decreases to 15.89 mm. Determine the modulus of elasticity (in MPa) and Poisson’s ratio for this metal.
Please answer in 30 minutes. STRENGTH OF MATERIALS (Please write the complete solutions and FBDs completetely and correctly. No long explanation needed.Thumbs up will be given) A loaded beam, 60 mm wide by 200 mm high and 8 in long, has the shear and moment diagrams as shown below. (a) Determine the magnitude, type and location of the maximum flexural stress (b) Determine the type and magnitude of stress in a fiber 40 mm from the top of the beam at a section 2.5 m from the left end, Express final answers in MPa. (Use I=bh3/12
Determine the design tensile strength of the plate (200 × 100) mm connected to a 12 mm thick gussets, using 20 mm bolts shown below, if the yield and ultimate stress of the steel used are 250 MPa and 420 MPa respectively, fy= 250 MPa fu= 450 MPa
Calculate the tensile steel strain of 5-16-mm-dia rebars in a concrete beam 270 mm by 410 mm at ultimate stage if f'c = 23 MPa and fy = 420 MPa. Express your answer in 5 decimal places.
A test piece is cut from a brass bar and subjected to a tensile test. With a load of 6.4 kN the test piece, ofdiameter 11.28 mm, extends by 0.04 mm over a gauge length of 50 mm. Determine:(i) the stress, (ii) the strain, (iii) the modulus of elasticity.(b) A spacer is turned from the same bar. The spacer has a diameter of 28 mm and a length of 250 mm, bothmeasurements being made at 20~ The temperature of the spacer is then increased to 100~ the natural expansionbeing entirely prevented. Taking the coefficient of linear expansion to be 18 x 10-6/~ determine:(i) the stress in the spacer, (ii) the compressive load on the spacer.rC.G.] [64 MN/m 2, 0.0008, 80 GN/m 2, 115.2 MN/m 2, 71 kN.] Could you please answer the parts after the first three? If you use * could you please explain what you mean by it! Thank You :)
Compression Steel Given: The beam cross-section shown have the following cross-sectional properities: f'c = 4000 psi Find phi Mn.