Water is flowing from the tank into a series of pipes and then into the atmosphere through 75 mm-diameter nozzle as shown in figure. Calculate the pressure P and the height H for the system. Neglect losses. water 150 mmda 175 mm 100 mmda 75 mmda Free jet

Water is flowing from the tank into a series of pipes and then into the atmosphere through 75 mm-diameter nozzle as shown in figure. Calculate the pressure P and the height H for the system. Neglect losses. water 150 mmda 175 mm 100 mmda 75 mmda Free jet

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

Water flows through the turbine shown at a rate of 0.386 m3/s. The pressures at points A and B are 161.2 kPa and -19.6 kPa, respectively. What is the electrical power generated by the turbine if it is 85% efficient?
An agricultural land install a pump with a 218mm diameter suction pipe and a 200mm diameter discharge pipe. Respectively each pressure reads 1.12 bars and 0.96 bars. The water flow measured 12.500 liters/min.at normal temperature. Calculate the following: 1. Head at the discharge side, m 2. Velocity Head. m 3. Total Head of the pump, m
Find the time required to drain the water completely from tank shown in figure
A pump is used to pump water from tank A (at atmospheric pressure) to tank B (at gauge pressure of 2 at). Given: distance between water levels in the two tanks is 25 m; pump capacity is 10 m3/h; suction pipe has: diameter of 100 mm, length of 10 m, friction coefficient of 0.025, and local coefficient of 2; discharge pipe has: diameter of 80 mm, length of 30 m,friction coefficient of 0.028, and local coefficient of 5; pump efficiency is 80%.a. Calculate the pump required power in hp.b. Why is the suction pipe diameter greater than or equal to the discharge pipediameter when design pumping system?
In Fig.2, A Pelton wheel has a mean bucket speed (U) of 89 m/s with a jet of water flowing at the rate of 1 m3/s under a head of 270 m. The buckets deflect the jet through an angle of 170º. Calculate the power delivered to the runner and hydraulic efficiency of the turbine. Take Cv = 0.98 , V= Cv root of 2gH , workdone per second by the jet on the runner = ρaV1 (Vw1 + Vw2) x U and Hydraulic efficiency ηh = 2 U (Vw1 + Vw2)/V12
The water flow of 35,000 Liters/min was developed into a booster station with a pump installed rated as follows: Pressure at Discharge side= 4.18 bars, 850mm above the pump C.L Suction Pressure= 220mmHg vacuum , 425mm below the pump C.L Pipe Dia @ suction=16 inches and Pipe Dia @ Discharge 12 ½ inches. 1. Draw the illustrative diagram 2. Calculate the Head at discharge, Velocity Head, Elevation Head and the Total Head of the Pump.
A fluid of specific gravity 0.8 and dynamic viscosity 15 x 10-4 Pa.s is flowing in a 15 mm diameter straight galvanized iron pipe (e = 0.3 mm, C = 130) of length 160 m. The flow velocity is 0.163 m/s. Calculate the friction head loss using Darcy-Weisbach and Hazen-Williams formulas.
Water flows from the ground floor to the third floor in a 4-storey building through a pipe 50 mm in diameter at a rate of 2 L/s and according to the diagram below. The water flows out from the system through a tap with an opening diameter of 15 mm. Q1. Calculate the energy loss due to friction as the water flows through the pipe (J/Kg) Q2. Calculate the total energy loss due to friction through the system (J/Kg) Q3. Calcualte the pressure at point 1 (kN/m2)
In the figure shown, water (ν = 1 x 10-6 m2/s) flows at a rate of 5 L/s on a system of pipes. There are 40 m of 50-mm diameter pipe, 22 m of 150-mm diameter pipe, and 45 m of 75-mm diameter pipe, all cast-iron. There are two 90o elbows and an open globe valve. If the exit elevation is zero, determine the following:a) friction loss on each pipeb) total minor loss from the surface of the reservoir to the exitc) head extracted by the turbined) mechanical power extracted by the turbine
Determine the rate of flow of water through a pipe of diameter 10 cm and length 60 cm when one end of the pipe is connected to a tank and other end of the pipe is open to the atmosphere. The height of water in the tank from the centre of the pipe is 5 cm. Pipe is given as horizontal and value of f= 0.01. Consider minor losses.
A centrifugal pump delivers water at the rate of 50 kg/s. The inlet and outlet pressures are 2 bar and 6.2 bar respectively. The suction is 2.2m below the centre of the pump and delivery is 8.5m above the centre of the pump. The suction and delivery pipe diameters are 200mm and 100mm respectively. Determine the capacity of the electric motor considering the efficiency of motor as 80% to run the pump.
A venturi meter with throat diameter of 37.5 mm and coefficient of discharge of 0.957 is connected to a 75 mm pipe to measure the discharge of oil with specific gravity of 0.853. A differential gage filled with liquid with specific gravity of 1.35 is connected. If there is a 415 mm difference in the height of the fluid in the meter, what is the flowrate of oil? (PLEASE USE BERNOULLI'S ENERGY EQUATION) INCLUDE COMPLETE SOLUTION PLEASE