İki silindir aralığına yerleştirilen bir akışkanın viskozitesi şekilde verilen bir düzenekle ölçülmektedir. Dakikada 300 devirde dönen iç silindirin çapı 20 cm ve yüksekliği 90 cm olarak verilmiştir. İki silindir arasındaki mesafe 1 mm'dir. Dönen silindire uygulanan moment 2 Nm olarak ölçüldüğüne göre akışkanın Dönmekte olan silindirin alt yüzeyindeki dinamik viskozitesini bulunuz. sürtünme ihmal edilmektedir.

İki silindir aralığına yerleştirilen bir akışkanın viskozitesi şekilde verilen bir düzenekle ölçülmektedir. Dakikada 300 devirde dönen iç silindirin çapı 20 cm ve yüksekliği 90 cm olarak verilmiştir. İki silindir arasındaki mesafe 1 mm'dir. Dönen silindire uygulanan moment 2 Nm olarak ölçüldüğüne göre akışkanın Dönmekte olan silindirin alt yüzeyindeki dinamik viskozitesini bulunuz. sürtünme ihmal edilmektedir.

Principles of Heat Transfer (Activate Learning with these NEW titles from Engineering!)

8th Edition

ISBN:9781305387102

Author:Kreith, Frank; Manglik, Raj M.

Publisher:Kreith, Frank; Manglik, Raj M.

Chapter5: Analysis Of Convection Heat Transfer

Section: Chapter Questions

Problem 5.18P: The drag on an airplane wing in flight is known to be a function of the density of air (), the...

See similar textbooks

Similar questions

The below results are for cooling tower expirement, energy balance :energy balance of the system, that is to say, the energy taken by the air must be equal to the energy supplied by the water flow. Question : Discuss the tabulated cooling tower results... Discuss in detail format!
Topic : Mixture Flow Problem A tank initially holds 100 gal of salt solution in which 50 Ib of salt has been dissolved. A pipe fills the tank with brine at the rate of 3 gpm, containing 2 lb of dissolved salt per gallon. Assuming that the mixture is kept uniform by stirring, a drain pipe draws out of the tank at 2pm. Find the amount of salt at the end of 30 minutes. Ans. 171.24 Ib
Suppose we got the following data during a test of a 2- stroke engine in which gas is usedas a fuel:Diameter of the piston = 149 mmStroke length = 179 mmClearance volume = 0.88 literrpm of the engine = 302Indicated mean effective pressure = 6.0 barGas consumption = 6.0 m3/hCalorific value of the gas (fuel) = 16990 kJ/m3Make a clear sketch the geometry of this engine using the data and determine thefollowing:i. Indicated power developed by the engine in watt.ii. Air Standard Efficiencyiii. Indicated thermal efficiency of the engine.
The drag on an airplane wing in flight is known to be a function of the density of air (), the viscosity of air(), the free-stream velocity (U), a characteristic dimension of the wing (s), and the shear stress on the surface of the wing (s). Show that the dimensionless drag, sU2, can be expressed as a function of the Reynolds number, Us.
Department of Mechanical Engineering PRINCIPLES OF COMPUTER AIDED ENGINEERING – MENG303 Please solve the problem by keupordDepartment of Mechanical Engineering PRINCIPLES OF COMPUTER AIDED ENGINEERING – MENG303 Please solve the problem by keupord
9.16. One kind of thermodynamic diagram that is useful in engineering problems is the P–H diagram, in which the x-axis is molar enthalpy and the y-axis is pressure.(a) Several kinds of iso-lines can be drawn in such a diagram, including isotherms(constant temperature), isentrops (constant entropy), and isochores (constant molar volume). For each of these three cases, find expressions for the slope of these lines on a P–H diagram in terms of measurable properties.(b) Find expressions for these slopes for the ideal monatomic gas, in terms of T and P. Explain on physical grounds any unusual results
A piece of lead (s.g. 10.7) is tied to a 136 cc of cork whose specific gravity is 0.16. They float just submerged in water. What is the weight of the lead in grams?
THERMODYNAMICS UPVOTE WILL BE GIVEN. PLEASE WRITE THE COMPLETE SOLUTIONS/DIAGRAMS LEGIBLY. NO LONG EXPLANATION NEEDED. USE 3 DECIMAL PLACES. BOX THE FINAL ANSWER. An airplane is cruising at an elevation of 35,000 feet from sea level. Determine the amount of gage pressure in bars needed to pressurize the airplane to simulate sea level conditions. The average atmospheric pressure on earth is mated as a function of altitude by the relation Patm = 101.325 (1- 0.02256z)5.256, where Patm is the atmospheric pressure in kPa and z is the altitude in km with z = 0 at sea level.
2014Q5: please answer each part with specific detail and reasoning for each part
HELLO HELP WITH NUMBER 2 PLEASE, COMPLETE SOLUTION, 4 DECIMAL PLACES. THANK YOUUU Your client asks yoy to construct a mobile accent for his house. You use an iron wite, 0.75m long and 2.75x10^-3 cm^2 in cross-sectional area and hang a brass cube of mass 8kg on one end. On the bottom of the brass cube, you attach a similar iron wire and hang another brass cube of mass 7.5kg. If young’s modulus elasticity for iron is 21x10^10Pa and that the weight of the iton wires is neglected. For the wire above, determine; A. Tensile stress B. Tensile strain C. Elongation
PROPAGATION OF ERROR You are tasked to supervise the design of 0.5MW wind turbine to be constructed in a Wind Farm in Pililla, Rizal. Suppose the design criteria are as follows: The air density as surveyed after 2 year period averaged at 1.225 kg / cubic meter. The sweeping diameter of the rotor blades is 125m, and the anemometer reading in the area amounts to 4.2m/s on a 2 year period of survey. if the diameter measurement is off by 0.1m and the anemometer reading is also fluctuating by 0.05m/s. In the design specifications given, if the actual measurement of power via the substation amounts to exactly 530kW and given that the windspeed is off by 0.05m/s, what could have been the error in the measurement of diameter? Your answer must be in 3 decimal places and in correct signs and measurement. Show complete solution in paper.
New York Building Corporation uses the critical path method to monitor construction jobs. The company is currently 2 weeks behind schedule on Job #181, which is subject to a P10,500 per week completion penalty. Path A-B-C-F-G-H-I has a normal completion time of 20 weeks, and critical path A-D-E-F-G-H-I has a normal completion time of 22 weeks. The following activities can be crashed. Activities Cost to Crash 1 Week Cost to Crash 2 Weeks BC P 8,000 P15,000 DE 10,000 19,600 EF 8,800 19,500 REQUIRED: 1. New York Building desires to reduce the normal completion time Job #181 and, at the same time, report the highest possible income…