In 2001, EPA adopted a lower standard for arsenic in drinking water that applies to both community water systems and non-transient non-community water systems. The new arsenic standard is 10.0 ppb. Please estimate the highest molarity of arsenic (in μM) in drinking water that can meet the standard of EPA? The density of pure water is 1.000 g/mL. ___________ μM?

In 2001, EPA adopted a lower standard for arsenic in drinking water that applies to both community water systems and non-transient non-community water systems. The new arsenic standard is 10.0 ppb. Please estimate the highest molarity of arsenic (in μM) in drinking water that can meet the standard of EPA? The density of pure water is 1.000 g/mL. ___________ μM?

Chemistry: The Molecular Science

5th Edition

ISBN:9781285199047

Author:John W. Moore, Conrad L. Stanitski

Publisher:John W. Moore, Conrad L. Stanitski

Chapter13: The Chemistry Of Solutes And Solutions

Section13.6: Expressing Solution Composition

Problem 13.9CE

See similar textbooks

Similar questions

Too much iron in drinking water can cause the following undesirable effects: rusty color; sediment; metallic taste; reddish or orange staining. The EPA's Secondary Maximum Contaminant Level for iron in drinking water is 0.300 mg/L. (1) If 3.82×104 liters of water in a storage tank contains 4.18 grams of Fe , what is the contaminant level in ppm? ______ppm. Assume that the density of the impure water is 1.00 g/mL. (2) Is this level acceptable based on EPA guidelines? ________
Too much manganese in drinking water can cause the following undesirable effects: black to brown color; black staining; bitter metallic taste . The EPA's Secondary Maximum Contaminant Level for manganese in drinking water is5.00×10-2 mg/L.(1) If 4.45×104 liters of water in a storage tank contains 10.0 grams of Mn , what is the contaminant level in ppm? ppm Assume that the density of the impure water is 1.00 g/mL.(2) Is this level acceptable based on EPA guidelines?
A sample (50 mL) of a bottled water was added to a 100 mL volumetric flask and then diluted to the mark. From this stock solution, 50 mL was taken, added to a 100 mL volumetric flask and diluted to the mark. Final concentration of the serial dilution: 587.7161ppm. 1. what is the concentration in the original bottle (ppm)
The solubility of Ce(IO₃)₃ (cerium (III) iodate) in 0.20 M KIO₃ (potassium iodate) is 4.4 x 10-8 M. What is Ksp for cerium (III) iodate? Enter your answer, rounded to the correct number of significant figures, using scientific notation in E notation. Ksp = ?
A cough syrup, which comes in a concentrated syrup, contains red dye #40.The red dye #40 syrup is diluted three consecutive times by a factor of 2 Match the dilution with the correct solution shown in the image. Water, undiluted syrup, dilution 1, dilution 2, dilution 3. If the concentration of red dye #40 in the original syrup is 4.68 x 10-3 M, what is its concentration in dilution #3?
You have 20 x SSC solution available in our wet lab, to make 400 ml 0.4 xSSC solution. How many ml 20 x SSC you will need?
What is 2.7 x 10^-3 grams of lead (Pb) per gram of solution?a. 2.7 ppmb. 2700 ppbc. 2700 ppmd. 2.7 ppb
An analysis was conducted to determine the potability of a 35.0-mg sample of tap water. The results revealed that the sample contain 1.8 x 10-3 μg of Lead (Pb). According to the Philippine National Standards of Drinking Water of 2017, the parameter for safe drinking water has a maximum allowable level (MAL) of 0.01 ppm of Lead (Pb) concentration. Determine whether the sample tap water is potable or not (through calculations), and briefly explain your answer.
1. A 0.68 gram sample of a volatile liquid was heated to 358 K. The gas occupied 265 mL of space at a pressure of 0.95 atm. What is the molecular weight of this gas? PV = nRT and R = 0.082 atmL/moleK. (Make sure that all your units agree/match R)2. An aspirin sample, 0.62 grams, was titrated with 28 mL of 0.105 M NaOH solution. What is the percent purity of this aspirin sample? (MM of Aspirin = 180. g/mol)3. A sample of hydrate was heated thoroughly. How many waters of hydration are there if the anhydrous salt had a dry mass of 12 grams and a molar mass of 185 g/mol? The mass of water evaporated from the hydrate was 5.0 g.4.A sample of water (80 grams) had a temperature change of 6. ℃. What was the heat change of this sample? (q = m c ΔT, c = 4.18 J/ g ℃)5. A 6.0 gram sample of epsom salt, MgSO4 ·nH2O, was heated. After heating, 2.9 grams of anhydrous salt remained. How many waters of hydration does epsom salt contain?6. What is the theoretical yield of aspirin if you started your…
Cedrick and Astrid a 20.00 ml aliquot of grapefruit juice with a 0.165 M NaOH solution to the end point. The initail buret reading was 1.72ml and final buret reading was 15.51ml. They calculated that there was 0.1457g of citric acid present in the juice sample. What is the amount mg of citric acid present per ml of juice? the answer is 7.29mg/ml. (can you please show me how to calculate this answer)
50 mL of stock solution were taken and added to flask. Then 50 mL of Di water were added to the flask. This is solution 1. Then 50mL of solution 1 were taken and added to a flask and 50 mL of Di water were added to the flask. This is solution 2. Then 50mL of solution 2 were taken and added to a flask and 50 mL of Di water were added to the flask. This is solution 3. Then 50mL of solution 3 were taken and added to a flask and 50 mL of Di water were added to the flask. This is solution 4. Find the concetrations of each solution. Information of stock solution - molar mass- 534.3g/mole 0.587g in MilliQ
What is water hardness? Differentiate temporary from permanent water hardness.