I need the answer as soon as possible English (en)HomeMy coursesSUMMER2021-0600208-SQ77965710EQuiz 6In a heat engine cycle, which of the following process occurs?a. heat is transferred from a furnace to a boilerO b. all of the mentionedO c. work is produced in a turbineO d. steam is condensed in a condenserضبابDIIF5F6F7F8F3F4#2$%57 V8.Y !U934(8)

In a heat engine cycle, which of the following process occurs O a. heat is transferred from a furnace to a boiler O b. all of the mentioned O c. work is produced in a turbine O d. steam is condensed in a condenser

In a heat engine cycle, which of the following process occurs O a. heat is transferred from a furnace to a boiler O b. all of the mentioned O c. work is produced in a turbine O d. steam is condensed in a condenser

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

Answer the following: A.) What is the significance of using multiple feedwater heaters? (Write your reference) B.)What is the difference of using multiple feedwater heaters and using only one feedwater heater with their efficiency of cycle? C.) State other things/ways to increase efficiency of a cycle, other than using multiple feedwater heaters.
Data for steady-state operation of a vapor-compression refrigeration cycle with Refrigerant 134a as theworking fluid are given in the table below. State 1 is at the compressor inlet. The cooling capacity (i.e therate at which heat is removed from the cooled space) is 4.6 tons. 1 ton of refrigeration is equivalent to211 kJ/min. Ignoring heat transfer between the compressor and its surroundings, sketch the ?-? diagramof the cycle and determinea) the mass flow rate of the refrigerant, in kg/min.b) the isentropic compressor efficiency.c) the coefficient of performance.State ? (bar) ? (°C) ℎ (kJ/kg) ? (kJ/kg-K)
c. Why is regenerative cycles used in steam power cycle? a. Decrease the Qout in the condenser b. DecreaseQin in the boiler c. Increase Wnet produced d.Decrease W required by the liquid pump
rankine cycle, the pressure and temperature entering the turbine is 1800 kpa and 380 degrees celsius and the pressure leaving the turbine is 20 kpa, the quality of steam entering the condenser is 90%. what is the turbine work in kj/kg at 1.8 mpa and 380 degrees celsius. engine turbine eff=85% mechanical ff=88% determine worknet,work brake, brake heat rate
Only solve last 2 parts ok Problem 2 – Heat Pump Thermodynamic Analysis Refrigerant-134a enters the condenser of a residential heat pump at 800 kPa and 50°C at a rate of 35 L/min and leaves at 750 kPa subcooled by 3°C. The refrigerant enters the compressor at 200 kPa superheated by 3°C. Neglecting changes in kinetic and potential energy and any stray heat transfer, please answer the following.a. Create a schematic of the cycle, use the same numbers used in your textbook for the inlet and exit states of each device, and include the energy exchanges between the cycle devices and the surroundings.b. Sketch the cycle processes on a T-s diagram.c. Determine the isentropic efficiency of the compressor.d. Compute the rate of heat supplied to the heated room.e. Determine the COP of the heat pump.
What are the advantages of using cascade refrigeration?I.Higher required pressure differences for compressorsII.Higher variety of refrigerants as working fluids per cycle. a.II only b.Neither I nor II c.I only d.Both I and II
use the refrigerant tables (134a for example) MODULE: THERMODYNAMICS QUESTION 1 A steady-flow Carnot refrigeration cycle uses refrigerant-134a as the working fluid. The refrigerant changes from saturated vapour to saturated liquid at 70°C in the condenser as it rejects heat. The evaporator pressure is 100 kPa. Show the cycle on a T-s diagram relative to saturation lines , and determine (a) The coefficient of performance, (b) The amount of heat absorbed from the refrigerated space (c) The network input. a. 2.56 ; 89.20 kJ/kg ; 213.29 kJ/kg b. 2.56 ; 89.20 kJ/kg ; 30.89 kJ/kg c. 2.56 ; 89.20 kJ/kg ; 17.89 kJ/kg d. 2.56 ; 89.20 kJ/kg ; 34.89 kJ/kg
typewritten please Give at least 3 Advantages of electrical Reheat Regenerative Cycle in Thermal Power Plant.
Recommend general considerations when selecting a site for Thermoelectric Power Plant.
A medium size power station is used to produce 30 MW net power for arefinery. The station uses steam as the operating fluid and operatesaccording to the Carnot cycle between the pressure limits of 0.4 bar and35 bar. Steam enters the boiler as a saturated liquid and leaves it as adry saturated vapour. (i) List the name of the four processes in a generic Carnot cycle andstate what type of energy transfer (work/heat) can be neglectedin each process. (ii) Determine the dryness fraction of the steam that is fed to thecondenser, and the specific enthalpy values at the four key points ofthe cycle. (iii) Calculate the specific heat provided to the boiler, the specificwork extracted from the power station and the mass flow rate ofthe steam circulating in the cycle, then, determine the thermal efficiency of the cycle.
There is a steam power cycle that uses water as the working fluid, where the condenser pressure is 20 kPa. The pressure in the boiler is 4 MPa. The steam that comes out of the boiler is saturated steam and the quality at the outlet of the turbine is ?4 = 0.65. The water enters the pump as a saturated liquid and exits at a temperature of 48 ° C (T2).Determine;a) work on the pumpb) heat transfer in theboilerc) work on the turbined) The heat in the condensere) The thermal efficiency of the cycle
22 - Refrigerant – 134a (refrigerant, R–134a) is used in a refrigeration machine working with an ideal vapor compression cycle, the condenser is kept at 1000 kPa pressure and the evaporator is at 6ºC. If the cooling load is 450 kW, which of the following is the mass flow rate? a) 6.43 kg/h B) 3.07 kg/h NS) 3.39 kg/h D) 2.75 kg/h TO) 6.58 kg/h