In a power system, the present installed capacity is 200O0MW. The peak demand is 1800MW. The annual increase in peak demand is happening at the rate of 20%. (a) Calculate the Future Reserve margin of the system next year if no additional installed capacity is added to the system. (b) What is your inference for reporting to higher officials as a Electrical reliability Engineer from above mentioned calculation?

In a power system, the present installed capacity is 200O0MW. The peak demand is 1800MW. The annual increase in peak demand is happening at the rate of 20%. (a) Calculate the Future Reserve margin of the system next year if no additional installed capacity is added to the system. (b) What is your inference for reporting to higher officials as a Electrical reliability Engineer from above mentioned calculation?

Introductory Circuit Analysis (13th Edition)

13th Edition

ISBN:9780133923605

Author:Robert L. Boylestad

Publisher:Robert L. Boylestad

Chapter1: Introduction

Section: Chapter Questions

Problem 1P: Visit your local library (at school or home) and describe the extent to which it provides literature...

See similar textbooks

Similar questions

Equal area criteria is a method used to calculate: Select one: O a. None of the answers b. Critical clearing angle and time for transient faults O c. Critical clearing voltage angle for transient faults d. Transient stability current limit O e. Steady state stability power limits
The reactance data for the power system shown in below figure in per unit ona common base is as the following: X²_x² j0.1 G₁ to j0.25 Ti Select one: O a. No right answer O b.-12.19 pu O c.-14.986 pu O d.-) 3.806 pu 2 j0.3 + AL j0.05 j0.25 Assume that the pre fault voltage at bus 2 = 1 pu. For bolted line (b) to line (c) fault at bus 2, the fault current is = j0.5 3 j0.25 T₂ 4 38 + A j0.25 j0.1 G₂ j0.05
Power system protection and control: Developing advanced protection and control systems that can detect and respond to faults and disturbances in the power grid in real-time. Describe how this problem will affect the world in 100 years
Developments that could happen in power flushing in the future
Voltage sags due to short circuit and earth faults are the cause for the vast majority of equipment problems. Electronics equipment become more susceptible to voltage sag, hence the companies experience production stoppages. Voltage sag analysis is very complex issue. Based on voltage sag randon factors describe on it.
Question 1:a) State why voltage control and cable stranding are necessary in powersystemsb) Briefly explain where and how the following state variables ofa power supply grid are controlled.i) Frequencyii) Active powerili) Reactive poweriv Voltage.
In power system scenario of Sultanate of Oman, the present installed capacity in year 2021 is 9000MW. The peak demand is 8500MW. The annual increase in peak demand is happening at the rate of 10%. (a) Calculate the Future Reserve margin of the system in year 2022 if no additional installed capacity is added to the system. [ Write Future Reserve Margin as answer) (b) What is your inference for reporting to higher officials as a Electrical reliability Engineer from above mentioned calculation for year 2022? [Write your answer in one sentence]
Discuss the role of power system protection in ensuring the safety and reliability of electrical grids.
A generator operating at 50 Hz delivers 1 p.u. power to an infinite bus through a transmission circuit in which resistance is ignored. A fault takes place reducing the maximum power transferable to 0.5 p.u. Where as before the fault, this power was 2.5 p.u. and after the clearance of the fault, it is 2 p.u. The value of 8 is max
(a) Give the condition for the loss of load in a power generation system in terms of outages in generation units (b) Give the assumption taken for the calculation of LOLP? [Write relevant Answers in 1 or 2 sentences in each part)
Fill in the blanks 1. Grounding is connecting …….. of electrical equipment to earth. 2. When a …………………………….… fault occurs on an ungrounded neutral system, the potential of the healthy phases rise to the line voltage. 3. The method of reactance grounding is not used because of ……………………… appearing under fault conditions. 4. The cosine of the angle between the ………………………………………. and the ………………………………...…… is called the sending end power factor. 5. The AC power delivered to a load is equal to ………........
A power generation plant connected to bulk load of high voltage industries shown in Figure Q3 has specifications given in Table Q3. Each equipment reactance is expressed in per unit on a common base of 100 MVA. a) Find the fault level for each bus bar in the generation plant. GI G2 TI Figure Q3: Single line diagram of a power generation plant Table Q3: Specifications of power system components Power System Component Voltage Rating X MVA Rating (kV) (pu) GI 50 33 0.2 G2 40 33 0.18 50 33/11 0.1 T2 40 33/11 0.1