In a reaction involving the iodination of acetone, the following volumes were used to make up the reaction mixture: 5.00 mL 4.55 M acetone + 10.0 mL 1.05 M HCI + 10.0 mL 0.00300 M l₂ + 25.0 mL H₂O a. How many moles of acetone were in the reaction mixture? Recall that, for a component A, moles of A [A] x V where [A] is the molarity of A and V is the volume in liters of the solution of A that was used. moles b. What was the molarity of acetone in the reaction mixture? The volume of the mixture was 50.0 mL, 0.0500 L, and the number of moles of acetone was found in Part (a). moles of A V of soln in liters [A] = M acetone c. How could you double the molarity of acetone in the reaction mixture, keeping the total volume at 50 mL and keeping the same concentrations of H+ ion and I2 as in the original mixture? Use mL acetone and mL water, keeping the volumes of HCl and I2 the same.

In a reaction involving the iodination of acetone, the following volumes were used to make up the reaction mixture: 5.00 mL 4.55 M acetone + 10.0 mL 1.05 M HCI + 10.0 mL 0.00300 M l₂ + 25.0 mL H₂O a. How many moles of acetone were in the reaction mixture? Recall that, for a component A, moles of A [A] x V where [A] is the molarity of A and V is the volume in liters of the solution of A that was used. moles b. What was the molarity of acetone in the reaction mixture? The volume of the mixture was 50.0 mL, 0.0500 L, and the number of moles of acetone was found in Part (a). moles of A V of soln in liters [A] = M acetone c. How could you double the molarity of acetone in the reaction mixture, keeping the total volume at 50 mL and keeping the same concentrations of H+ ion and I2 as in the original mixture? Use mL acetone and mL water, keeping the volumes of HCl and I2 the same.

Chemistry

10th Edition

ISBN:9781305957404

Author:Steven S. Zumdahl, Susan A. Zumdahl, Donald J. DeCoste

Publisher:Steven S. Zumdahl, Susan A. Zumdahl, Donald J. DeCoste

Chapter18: Electrochemistry

Section: Chapter Questions

Problem 3RQ: Table 17-1 lists common half-reactions along with the standard reduction potential associated with...

See similar textbooks

Similar questions

A sample containing chlorophenol, C6H4ClOH, was analysed by gravimetric analysis. A 0.783-g of this sample goes through a chemical process allowing the chlorine in the chlorophenol to precipitate as silver chloride, weighing 0.271 g. Calculate the % (wt/wt) of the chlorophenol in the sample, assuming that chlorophenol is the only source of chlorine in the sample. Provide your answer to two decimal places and without units. Avoid using scientific notation.
Potassium acid phthalate, KHC8H4O4 ( MM=204.2 ), reacts with sodium hydroxide on a 1:1 molar basis. A sample of the acid weighing 0.4823 g was titrated with NaOH, requiring 24.35 mL to reach the endpoint. Calculate the molar concentration of the sodium hydroxide solution.
A K2SO4 solution is prepared by weighing out a certain amount of the pure solid reagent,dissolving it to 500.0 mL in a volumetric flask. An aliquot was taken from this solution.of 25.00 ml and diluted to 500.0 ml. An aliquot of 5.00 was taken from this new solution anddiluted to 50.00 ml. A chemical analysis of this new solution showed a 0.100%(w/v)in K+. Calculate the weight of the pure solid K2SO4 used for the preparation of the original solution.and its concentration in each volumetric flask. The answer is 2.23x10^2g
Consider the titration illustrated in Figure 8.] Anhydrous sodium carbonate (Na₂CO₃) is a primary standard. When 0.364 grams of the substance is placed in a conical flask, then 20.00 cm³ of sulphuric acid (H₂SO₄) solution is required to reach the end point of the titration. What is the concentration in mol·dm⁻³ of the sulphuric acid solution? [Give the answer to 3 decimal places. Do not type in the unit. Use a decimal point.] *
The solubility of borax, which is made up of sodium tetraborate (Na2B4O5(OH)4 8H2O), was analyzed. The dissolution of borax is: Na2B4O5(OH)4 • 8H2O(s) ⇌ 2 Na+(aq) + B4O5(OH)42–(aq) + 8 H2O(l) A 50 mL saturated solution was prepared. After filtration of solution, 5 mL aliquot was transferred to a flask and titrated using 0.432 M HCl. The endpoint was found to be 4.73 mL of the titrant. Tetraborate anion (B4O5(OH)42-) is a weak base which reacts with HCl like the following reaction: B4O5(OH)42–(aq) + 2 H+(aq) + 3 H2O(l) ⇌ 4 H3BO3(aq) What is Ksp expression for the dissolution? What is the tetraborate ions concentration in the filtrate? What is the molar solubility and Ksp of borax if the titration was done at room temperature (298 K)?
Describe in detail the steps involved to prepare following solution; a) 0.2% (v/v) , (v/w), (w/v) and (w/w) solution of acetic acid.
Table 17-1 lists common half-reactions along with the standard reduction potential associated with each half-reaction. These standard reduction potentials are all relative to some standard. What is the standard (zero point)? lf is positive for a half-reaction, what does it mean? If is negative for a half-reaction, what does it mean? Which species in Table 17-1 is most easily reduced? Least easily reduced? The reverse of the half-reactions in Table 17-1 are the oxidation half-reactions. How are standard oxidation potentials determined? In Table 17-1, which species is the best reducing agent? The worst reducing agent? To determine the standard cell potential for a redox reaction, the standard reduction potential is added to the standard oxidation potential. What must be true about this sum if the cell is to be spontaneous (produce a galvanic cell)? Standard reduction and oxidation potentials are intensive. What does this mean? Summarize how line notation is used to describe galvanic cells.
A 0.2500-g of dry CaCO3 was completely dissolved into a solution of 5-mL conc. HCl and 50-mL distilled water in an erlemeyer flask. The resulting solution was boiled for 5 minutes to expel CO2 from the reaction, and then it was cooled to room temperature and the solution was transferred in a 500-mL volumetric flask filled to volume by rinsing the erlenmeyer flask and combining all the washings to fill the mark. A 5.0-mL aliquot of the CaCl2 solution was taken from the orignal solution and was transferred into an erlenmeyer flask with 10-mL NH3 buffer, 20-mL distilled water, and 5 gtts of EBT. The solution consumed 4.96 mL of an EDTA solution. MW: CaCO3 = 100.1 Compute for the N EDTA solution. 0.0053 N 0.0531 N 0.5313 N None of the choices
The hardness of water (hardness count) is usually expressed in parts per million (by mass) of CaCO3. What is the molar concentration of Ca2+ ions in a water sample with a hardness count of 175mg CaCO3il? How many milliliters of concentrated sulfuric acid, 94.0% (w/w), specific gravity of 1.831 are required to prepare 1 liter of a 0.100 M solution? The solubility-product constant for Ce(IO3)3 is 3.2x1010. What is the Ce3+ concentration in a solution prepared by mixing 50.0 ml of 0.0250 M Ce3.. with 50.00 ml of water?
Calculate the value of the reaction quotient, Q, of silver iodate (AgIO3) when 10.0 mL of 0.018 M AgNO3 is mixed with 10.0 mL of 0.018 M NaIO3. (Please give your answer with 2 significant figures.)
To determine the fluoride content in an aqueous and chloride-containing preparation of ammonium fluoride, the following analysis was performed. 105.2 mg of the preparation was dissolved in 100.0 mL of water. Then a 300 mL 40 mM lead chloride solution was added, whereby all fluoride ions were precipitated out of the solution in the form of the sparingly soluble salt PbClF (s). The precipitate was separated and washed at 15 degrees with a lead fluoride chloride saturated solution and dried at 130 degrees. The precipitate weighed 651.3 mg. a) Calculate the fluoride content (as % by weight F) in the preparation.b) Determine the purity of the ammonium fluoride preparation
Calculate the heat loss or heat gain of the 3 solution mixtures (qrxn). Then calculate the ΔH for reaction. mass:(20mL) density:1.02g/mL)