In a reservoir, the pressure of a compressed gas must not be increased past 825 kPa. The gauge indicated 388 kPa when the temperature is 24oC. Determine the maximum temperature which can safely be attained in the reservoir

In a reservoir, the pressure of a compressed gas must not be increased past 825 kPa. The gauge indicated 388 kPa when the temperature is 24oC. Determine the maximum temperature which can safely be attained in the reservoir

Refrigeration and Air Conditioning Technology (MindTap Course List)

8th Edition

ISBN:9781305578296

Author:John Tomczyk, Eugene Silberstein, Bill Whitman, Bill Johnson

Publisher:John Tomczyk, Eugene Silberstein, Bill Whitman, Bill Johnson

Chapter2: Matter And Energy

Section: Chapter Questions

Problem 17RQ: At a constant pressure, how does a volume of gas vary with respect to the absolute temperature?

See similar textbooks

Related questions

Q: Part A Ball A has a mass of 3 kg and is moving with a velocity of (va)ı = 8 m/s when it makes a dire...

Q: Explain ideal Rankine cycle with P-V, T-S and h-S plot.

A: GIVEN DATA - IDEAL RANKINE CYCLE GIVEN WE HAVE TO EXPLAIN WITH TS ,HS & PV PLOT

Q: Fig. Q3 c E KN in c maximo at joint C

Q: A centrifugal pump delivers 1.27 m' of water per 1200 r.p.m. The impeller diameter is 350 mm and bre...

Q: 60 Ib 90 lb 30 45 150 lb

A: GIVEN DATA- A 150lb BOX GIVEN ACTED BY TWO FORCES WE HAVE TO FIND ACCELERATION OF IT

Q: Four kilogram of steam is initially at 1MPa and y=40% inside the piston cylinder. There is a 30C sup...

A: In the case of pure substance, when heat is removed or given to steam, it can achieve saturated liqu...

Q: Q. 5. A toy cart has mass of 4 kg and is kept on a smooth horizontal surface. Four blocks A, B, C an...

A: Given Mass of cart, m = 4 kg Force, F = 40 N Gravity, g = 10 m/s...

Q: explain why testlights are not recommended for testing computer circuits.

A: A test light is less expensive and less complicated than a multimeter, yet it may often be used t...

Q: 1) How much stress will be generated in the 13mm diameter aluminum rod below with an increase in tem...

A: Answer: The stress generated in the aluminum rod is 13.89 MPa.

Q: explain what happened here.

A: Given: Load current - Voltage graph

Q: a) Determine the work done by the steam on the piston if steam is admitted to the cylinder at 20 bar...

Q: must show all pertinent solutions and the illustration that supporting the answer. Please list the g...

A: Given:μ=0.14+0.xyμ=0.14+0.68μ=0.82

Q: Problem 5. Both ends of a 1-foot organ pipe are open. What are the frequencies of the fundamental an...

Q: Given: w1 = 60 kN/m, w2 = 30 kN/m, P = 40 %3D %3D kN, a = 3 m, b= 3 m, and c = 3 m. Determine %3D %3...

Q: Given is a truss structure: Where: • Working shear stress for the rivets is 70 MPa • Working bearing...

A: TRUSS:- is a rigid structure in which all he members are subjected to either axial or tensile or ax...

Q: :) In an air standard diesel cycle, the pressure and volume of beginning of compression are 200 kPa ...

A: Given:P1=200 KPav1=0.05 m3P2=5.2 MPaP4=400 KPa

Q: What are primary sources and why are they important

A: Academics require this knowledge to comprehend and teach the intricacies of those intersections,...

Q: A device's outer cylinder diameter is 5" and its distance from outer cylinder to the inner cylinder ...

Q: What are the advantages of a self-adjusting clutch?

Q: In a tubular heat exchanger of the steam-water type, dry and saturated water vapor whose pressure is...

Q: determine the percentage decrease in the volume of water.

A: determine the percentage decrease in the volume of water.

Q: 2. For superheated water, given a pressure P-0.2 MPa, calculate the internal energy (1) and enthalpy...

A: GIVEN- TABLE A-6 DETERMINE- INTERNEL ENERGY AND ENTHALPY AT 560 DEGRE...

Q: 1. The cantilever beam in Figure 1 is fixed at A, and is loaded with a distributed load from B to C ...

Q: would find the velocity of each point (no values given just the equation) for an overlapping/superim...

Q: Water vapour at 135 kPa and 183 is compressed isothermally until half the vapour has condensed. How ...

A: GIVEN DATA - WATER VAPOUR AT 135KPa AND 183'C COMPRESSED ISOTHERMALLY WE HAVE TO FIND WORK

Q: 1. Neglecting the weight of the steel wire, determine its required diameter if it is 30 ft long, han...

A: Given data, L= 30 ft = 360 in Elongation ∆L= 0.4 in P= 500 lb E= 49*10⁶ psi Stress limit s= 200...

Q: What are secondary sources and why are they important?

A: Secondary Source Definition and its importance.

Q: Problem: Referring to the structural members of truss in the figure, determine the internal axial st...

Q: Show Isometric View. Use Dimlinear for measurement FRONT VIEW L.H.SIDE VIEW I 20 20 20 50 20 30 20 2...

A: Isometric View using the above three views are as follows

Q: Use MATLAB to c

A: Question is not visble. But we don't have to send the matlab aceses to accounts.

Q: Why do we need to calibrate temperature measuring devices?

A: Temperature measuring devices can range from thermometers to optical sensors. Generally, these measu...

Q: A worker develops a tension Tin the cable as he attempts to move the 50-kg cart up the 20° incline. ...

Q: Determine the stress acting in members AB, BD and BE of th members is 15 in2

A: Need to determine Stress.

Q: Two Carnot heat engines run in series with the efficiency of first engine is k times the second. If ...

Q: An ideal Otto engine, operating on the hot-air standard with k = 1.34, has a compression ratio of 5....

A: Given Datak=1.34rk=5V=6 cu.ftT1=100°FP=13.75psia ***As per our company policy we are supposed to do ...

Q: Using the figure below, solve for the total head loss given that the pressure drop between the junct...

A: For solution refer below images.

Q: Five kilo of water vapour are contained at 178 kPa and 85 percent quality is a suitable enclosure. C...

Q: 5. A sensor is a device that receives and reacts to a signal such as a change in position, temperatu...

Q: The free convection heat transfer coefficient on a thin hot vertical plate suspended in still air ca...

A: Given Temperature, Tplate = 277 °C Tinf = 28°C Mass, m...

Q: weighing 150 N is at a 20° inclination from the ground. Its mass is 15.291 kg and has a dimension of...

Q: A hollow cylindrical column is placed on a steel plate on a concrete pedestal, if it supports a comp...

Q: A water tank with a capacity of 1500 L is desired to be completely filled in about 1.5 hours. The to...

Q: 7. At the beginning of compression in an ideal air standard Diesel cycle, the compression ratio is 1...

A: as per guideline i have to solve only three subpart of your question

Q: 6 cu. m of oil weighs 46,800 N, calculate the following a. Unit weight in N/cu. m b. Density in kg...

A: Given:V=5.6 m3W=46,800 N

Q: A device's outer cylinder diameter is 5" and its distance from outer cylinder to the inner cylinder ...

Q: a) A 6600V, 3 phase, star connected synchronous motor draws a full load current of 80 A at 0.8 power...

Q: A closed system undergoes a thermodynamic cycle with three steps: process 1-2 (from state 1 to state...

Q: ] Derive the differential equation of motion for the system shown; Determine th e of the steady stat...

A: Given- m=6kg k=8 KN/m c=40 N-s/m Y=80mm=0.08m ω=30 rad/sec

Q: The 2.4-Mg car increases its speed uniformly from rest to 22 m/s in 38 s up the inclined road. (a) D...

A: Givenmass of the car m=2.4Mg=2400kgU=0 at restV=22m/s finalt=38sε=0.8

Q: Calculate the specific weight, density, specific volume and relative density of oil which has weight...

A: GIVEN DATA- A OIL HAS WEIGHT 7N/litre WE HAVE TO FIND WEIGHT DENSITY , DENSITY , SPECIFIC VOLUME AND...

Concept explainers

Thermodynamic Relations

Thermodynamics is the division of physics that deals with the transfer of any kind of energy, whether it be heat, temperature, or work, from one object to another.

Question

ReadSpeaker webReader: Listen

In a reservoir, the pressure of a compressed gas must not be increased past 825 kPa. The gauge indicated 388 kPa when the temperature is 24^oC. Determine the maximum temperature which can safely be attained in the reservoir

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

SEE SOLUTION Check out a sample Q&A here

Step 1

VIEW

Step 2

VIEW

Step by step

Solved in 2 steps with 1 images

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, mechanical-engineering and related others by exploring similar questions and additional content below.

Similar questions

In a reservoir, the pressure of a compressed gas must not be increased past 825 kPa. The gauge indicated 388 kPa when the temperature is 24oC. Determine the maximum temperature which can safely be attained in the reservoir
The gauge pressure of a car tire is measured as 125 kPa before a trip, and 189 kPa after the trip, at a location where the atmospheric pressure is 95 kPa. Assuming that the volume of the tire remains constant and the air temperature before the trip is 101.3 ° C, determine the temperature of the air in the tire after the trip.
Consider water initially at 20°C and 1 atm. Determine the final density of the water (a) if it is heated to 50°C at a constant pressure of 1 atm, and (b) if it is compressed to 100-atm pressure at a constant temperature of 20°C. Take the isothermal compressibility of water to be α = 4.80 × 10−5 atm−1.
A 0.76 m^3 tank is to be filled with saturated vapor at 12.34 bar. determine the mass necessary and its temperature
Q6/ A 3.27-m3 tank contains 100 kg of nitrogen at 175 K. Determine the pressure in the tank, using (a) the ideal-gas equation, (b) the van der Waals equation, and Compare your results with the actual value of 1505 kPa.
The pressure of an automobile tire is measured to be 190 kPa (gage) before a trip and 215 kPa (gage) after the trip at a location where the atmospheric pressure is 95 kPa. If the temperature of air in the tire before the trip is 25°C, the air temperature after the trip is
The absolute pressure of an automobile tire is measured to be 320 kPa before a trip and 335 kPa after the trip. Assuming the volume of the tire remains constant at 0.022 m3, determine the percent increase in the absolute temperature of the air in the tire.
The average atmospheric pressure in Denver (elevation = 1610 m) is 83.4 kPa. Determine the temperature at which water in an uncovered pan boils in Denver.
A 2-m3 rigid vessel contains helium initially at a gage pressure and temperature of 320 kPa and 315 K respectively. Because of the leaks in the fittings of the vessel, the gage pressure dropped to 280 kPa and the temperature decreased to 300 K, determine the mass of the helium that leaked out and also the mass of nitrogen that remained in the vessel. (Ans. 0.06399 kg, 1.2240 kg)
This thermodynamics statement is false to say that a basic way to reduce the mean velocity of water flowing through a pipe for a given mass flow rate and density is to decrease the inside diameter of the pipe? Why is this statement false? Please explain. Thank you!
If you are not sure ,Kindly skip. I will rate after verifying the final answer. Determine the specific volume of water at 400 kPa and 100 C.
The piston in a car engine compresses a mixture of gasoline vapour and air from 700ml to 100ml during its compression stroke. Before the compression stroke, the mixture had a pressure of 75 kPa and a temperature of 120celcius. What is the pressure of the cylinder after the compression stroke if the temperature of the gas rises to 200celcius? Express your answer in MPa with two significant digits.