In a tensile test for an aluminum alloy, the sample used is 2 inches long and 0.5 inches in diameter. The proportional portion of the tension stress-strain diagram for an aluminum alloy is shown below. Determine the modulus of elasticity for this material: ____x106 lb/in2. Pay attention to units and calculate your answer to 1 decimal place for the unit specified above. In a tensile test for an aluminum alloy, the sample used is 2 inches long and 0.5 inches in diameter. The proportional portion of the tension stress-straindiagram for an aluminum alloy is shown below._x106 lb/in²Pay attention to units and calculate your answer to 1 decimal place for the unit specified above.σ (ksi)70t0.00614Determine the modulus of elasticity for this material:€ (in./in.)

A tensile test is performed on an aluminum specimen, whose length is 2 inches and diameter is 0.5…

In a tensile test for an aluminum alloy, the sample used is 2 inches long and 0.5 inches in diameter. The proportional portion of the tension stress-strain diagram for an aluminum alloy is shown below. Determine the modulus of elasticity for this material: _x106 lb/in². Pay attention to units and calculate your answer to 1 decimal place for the unit specified above. σ (ksi) 70 0.00614 € (in./in.)

In a tensile test for an aluminum alloy, the sample used is 2 inches long and 0.5 inches in diameter. The proportional portion of the tension stress-strain diagram for an aluminum alloy is shown below. Determine the modulus of elasticity for this material: _x106 lb/in². Pay attention to units and calculate your answer to 1 decimal place for the unit specified above. σ (ksi) 70 0.00614 € (in./in.)

Engineering Fundamentals: An Introduction to Engineering (MindTap Course List)

5th Edition

ISBN:9781305084766

Author:Saeed Moaveni

Publisher:Saeed Moaveni

Chapter7: Length And Length-related Variables In Engineering

Section: Chapter Questions

Problem 43P: A 10 cm long rectangular bar (when subjected to a tensile load) deforms by 0.1 mm. Calculate the...

See similar textbooks

Similar questions

A 10 cm long rectangular bar (when subjected to a tensile load) deforms by 0.1 mm. Calculate the normal strain.
A tension test performed on a metal specimen to fracture produced the stress– strain relationship shown in Figure P1.14. Graphically determine the following (show units and all work): a. Modulus of elasticity within the linear portion. b. Yield stress at an offset strain of 0.002 m/m. c. Yield stress at an extension strain of 0.005 m/m. d. Secant modulus at a stress of 525 MPa. e. Tangent modulus at a stress of 525 MPa.
A specimen is originally 300 mm long, has a diameter of 12 mm, and is subjected to a force of 2.4 kN. When the force is increased from 2.4 kN to 9 kN, the specimen elongates 0.250 mm. Determine the modulus of elasticity for the material if it remains linear elastic. Express your answer to three significant figures and include the appropriate units.
Consider a 1,000-mm long, 25-mm diameter sample subjected to a tension test. Automatic high-precision gages recorded that for an applied load of 150 kN, the sample experienced a longitudinal strain of 2×10−3mm/mm. Assuming that the material remained elastic while loaded, determine its modulus of elasticity. A. 175.0 GPa B. 63.7 GPa C. 152.8 GPa D. 72.9 GPa Which of the following occurs when the value of Poisson’s ratio is doubled and the modulus of elasticity is kept constant? a. The lateral deformations experienced by the material is halved b. The volume of the material will remain constant when subjected to external forces c. The elastic region of the shear stress-strain diagram would be less steep d. The material can withstand higher amounts of stress before permanent deformations occur
A specimen is originally 1 ft long, has a diameter of 0.5 in., and is subjected to aforce of 500 lb. When the force is increased from 500 lb to 1800 lb, the specimenelongates 0.009 in. Determine the modulus of elasticity for the material if it remainslinear elastic.Note: Draw the given data.
) Consider a cylindrical specimen of a steel alloy 10.0 mm in diameter and 75 mm long that is pulled in tension. (a) Determine its elongation when a load of 20,000 N is applied. (b) What is the modulus of elasticity? (c) What is the strength at a strain offset of 0.002? (d) What is the tensile strength?
STRENGTH OF MATERIALS. Please show the complete solutions. Rate will be given. Answer in 3 decimal places! The compound shaft consists of solid steel and bronze shafts and hollow aluminum shaft (D= 2.25" and d=0.90''). It is subjected to two torques as shown in the figure. The moduli of rigidity for steel, aluminum, and bronze are 12x106 psi, 4x106 psi, and 6x106 psi, respectively. Determine the shearing stress developed in each material. Also, calculate the angle of twist incurred by the aluminum shaft.
From the figure shown, Determine: The plastic section modulus about the horizontal axis. x10^6 mm^3 (3 decimal places)
A thin sheet of rubber in the form of a square is uniformly deformed into the parallelogram shape as shown in the figure. All edges remain the same length a, as the sheet deforms. Determine the average normal strain along the diagonal AC. Length a is in inches. Answer in 4 decimal places
Deflection Given: the beam cross-section shown have the following cross-sectional properties f'c = 4000 psi n = 8 Find Instantaneous Deflection and long-term deflection ( 4 year life; 30% sustained load).
STRENGTH OF MATERIALS (NO EXPLANATION NEEDED. THUMBS UP WILL BE GIVEN) For the given system, Member (1) undergoes a linear deformation (in mm) equal to a. 2.4x10^3 b. 2.4 c. 3.6 d. 3.6x10^3
Consider a cylindrical specimen of a steel alloy (Please see the figure) 0.33 in. in diameter and 3.15 inches long that is pulled in tension. solve:1. Its elongation when a load of 14,500 lb is applied2. Tensile stress point (stress and strain values)3. Ultimate stress point (stress and strain values)4. Fracture point (stress and strain values)