In a Wheatstone bridge, R₁ = 3,000, R4 = 4,000, R₂ = 6,000, and R3 = 8,000 ohms atbalance. Find the open-circuit output voltage if AR₁ = 30, AR₁=-20, AR₁=40, AR₁=-50, and Eex = 50 volts. If the bridge output is connected to a meter of 20,000 ohmsresistance, what will the output voltage now be?

Answered: Image /qna-images/answer/682f085c-dada-4377-bf34-56baa8b67e5a.jpg

In a Wheatstone bridge, R₁ = 3,000, R4 = 4,000, R2 = 6,000, and R3 = 8,000 ohms at balance. Find the open-circuit output voltage if AR1 = 30, AR₁=-20, AR₁=40, AR₁= -50, and Eex = 50 volts. If the bridge output is connected to a meter of 20,000 ohms resistance, what will the output voltage now be?

In a Wheatstone bridge, R₁ = 3,000, R4 = 4,000, R2 = 6,000, and R3 = 8,000 ohms at balance. Find the open-circuit output voltage if AR1 = 30, AR₁=-20, AR₁=40, AR₁= -50, and Eex = 50 volts. If the bridge output is connected to a meter of 20,000 ohms resistance, what will the output voltage now be?

Delmar's Standard Textbook Of Electricity

7th Edition

ISBN:9781337900348

Author:Stephen L. Herman

Publisher:Stephen L. Herman

Chapter18: Resistive-inductive Parallel Circuits

Section: Chapter Questions

Problem 8PP: In an R-L parallel circuit, ET=48 volts, IT=0.25 amps, R=320. Find XL.

See similar textbooks

Similar questions

L=4mH C=2uF, the input voltage Vs shown in the graph is applied to the circuit. what is the value of ic current in t=8 miliseconds
question from book ELECTRONIC CIRCUIT DESIGN : Question No.3 A designer designs the circuit given in figure 3. You have to analyse it to find thefollowing parameters: a.VB ,VE, IE , IB, VS , VCE, VDS. Replace the JFET with D-typeMOSFET and find b.Vc ,VG ,VDS ,VCE c. Is there any difference between the parameters found forJFET.
For the circuit in the figure, find the ones requested in the questions by using the following values? Vcc= 14 V, β=139, RF=326 kΩ, RC=4,5 kΩ, RE=0,9 kΩ IE=VCE=VCB=
S2.2 Which of the following Common Source Amplifier's generalone of its features.A) The voltage gain of the circuit is always less than 1.B) There is no phase difference between the output signal and the input signal of the circuit.C) There is a phase difference of 1800 between the output signal and the input signal of the circuit.D) The voltage gain of the circuit is always less than 1.
For circuit shown ini the pic. below, assuming VBE = 0.7 V.Determine: (a) IBQ(b) VB(c) ICQ(d) VE(e) VC(f) VCEQ
The four-resistor bias network of Figure12.22(a) on page 620 has VCC = 15 V, R1 = 100 kΩ, R2 = 47 kΩ, RC = 4.7 kΩ and RE=4.7 kΩ. Suppose that β ranges from 50 to 200, VBE = 0.7 V, and the resistors have tolerances of ±5 percent. Calculate the maximum and minimum values for IC.
21/ Potential Divider Principle is the simplest way of producing a source of higher EMF from a source of lower EMF. Select one: True False
VO output voltages in the circuits below. i- VA = 0V, VB= 0Vii- VA= 3V, VB =5Viii- VA= 0V, VB =3Viv- VA=3V, VB =0V Current flowing from M3 and M5 PMOS transistors in option a, and 1 kΩ R1 resistor in option b calculate the current flowing through it? Vt = 0.5 V, μnCox(W/L)= μpCox(W/L)=1 mA/V2 take it. λ=0 take it.
There are four networks in series, the first network has a gain of 15 dB, second has a loss of 5 dB, third gain of 25 dB, and last stage a loss of 3 dB. A certain signal serve as the input of the cascaded stage resulting to an output of 25.5W of power. (a) what will be the overall gain/loss of the whole system in dB? (2 points, Use 2 decimal places); (b) what is the input power in mW (3 points, Use 2 decimal places)
Please solve the problem. Thank you (Electronics) Given zener voltage at 9V, input voltage at 12Vdc to 15Vdc and ILmax at 40mA. What is Rsmin if Izmaxrated is 50mA?Define also what is Rsmax? Choices: a) 43 ohms b)10 ohms c) 50 ohms d)20 ohms
You were tasked with modifying an audio amplifier circuit. Amplifier circuits are responsible for increasing the current sent to the speakers, avoiding damaging the sound device. The original design is shown in the figure. You want to increase the current I1 by a factor of 10 (10 times). The conditions of the design area are: Both font values must be increased. None of the values can be equal to 0. What are the new values that you propose for the design of the amplifier? ** Argue your answer by analyzing the results obtained through calculations. (Check image 4 for the circuit)
1a) Please detail the importance of Analog and Digital Electronics. Write several applications and their usefulness. b) Define Superposition and Thevenin’s Theorem. Show an example with evidence. c) Define a Multiplexer circuit with an example. d) Show an Example of Ring Counters.