In DC power transmission High voltage Direct current transmission refers to the voltage level of near to 660 kV O less than 400 kV O 800 kV or higher O 800 kV

Q: Q) Shunt PMMC was designed by using indirect method to provide an ammeter with current range 5A,…

A: This question belongs to electrical measurements . It is based on the calculation of shunt…

Q: Contactor is used in 3phase motor control circuit to control the short circuit current. Select one:…

A: In this answer let us discuss what is a contactor and how it is used in the 3 phase motor control…

Q: 73. The full-load copper loss of a trans¬former is 1600 W. At half-load, the copper loss will be

A: —

Q: 2. Determine the DC (currents, terminal voltages and inter-electrode voltages) parameters of the…

A: We need to find out current and voltage for given circuit

Q: The voltage level of the low tension cables is up to V. O 6000 O 2000 O 1000 O 5000

A: The voltage level of the low tension cables is up to 1000 volt.

Q: The existing condition of the power system can be determined by analysis. O Stability Power Flow…

A: Answer is power flow analysis

Q: In DC power transmission, the voltage level of High Voltage Direct Current (HVDC) transmission is 17…

A: We need to select correct option for HVDC .

Q: find the average power delivered to each of the passive elements. verify the answer by calculating…

A:

Q: Three coils each having resistance of 25 Q are connected in delta across 425 V, 50 Hz supply. Then…

A: As per the guidelines, we supposed to answer one question at a time so please ask other questions…

Q: Consider designing an ammeter with a proper shunt resistance. In order to find such shunt, the…

A:

Q: Minimize the following minterms using K-MAP Y= m (1, 3, 5 , 9, 11, 13)

A: Given; Y=m1,3,5,9,11,13 The K Map is as follows; Y   c,d           00 01 11 10 a,b 00 0 1 1 0…

Q: ind Vx, using Superpositi

A:

Q: Q1) For a DC circuit if branch one, R1=2 Q, R2=4 Q are connected in series, and branch two, R3=1 Q…

A: In Branch 1  R1 and R2  are connected in series.

Q: the closed loop solar water collector, only water can be used as collector fluid O True O False

A: False .

Q: Q13. In case of D.C. machines, mechanical losses are primary function of (a) Current (b) Voltage (c)…

A: Mechanical losses mainly consists of friction and windange losses.

Q: The effective resistance of a coil is 100 Q. When 12VDC 160 mA of current is measured. The AC…

A: Given that, effective resistance =100 ohm dc supply voltage = 12 Vdc current =160 mA   we have to…

Q: Turbine power of a wind turbine is the sum of wind power and the power coefficient Select one: O…

A: Turbine power is the product of wind power and power coefficient

Q: Source Transformation Method Calculate the current I from the following circuits

A: In this question we will find current through source transformation..

Q: The equation to find the percentage ripple of a DC power supply is V no load-V full load V full load…

A: Given equation is used to find the ripple Voltage or not.

Q: A line consist of a pure resistance and a coil in series. The power dissipated in the resistance is…

A: In this question,  We need to Find the voltage at the sending end? We know P= VI watt Where V…

Q: CALCULATE VOLTAGE CURRENT, POWER FACTOR & POWER, BEFORE AND AFTER L1(48mH).

A:

Q: In a transmission system, step up transformers are used to increase the voltage for increasing the…

A: On voltage level the transformer have two types, Step up transformer Step down transformer In a…

Q: In a transmission system, step up transformers are used to increase the voltage for decreasing the…

A: (1)Step up transformer used to increase the transmission voltage. In high voltage transmission…

Q: The voltage level of the low tension cables is up to. V. O 6000 O 5000 O 1000 O 2000

A: The tension is the operating voltage of the transmission lines. According to the tension the cable…

Q: A. Minimum current circuit Circuit connection for minimum current delivered by a 30V DC source:…

A:

Q: Design a short circuit shunt stub that will match a 50 ohm line into a 100 + j100 ohm load.

A: We need to design a short circuit stub that with match a 50 ohm line into a 100+j100 ohm load.

Q: High-voltage transmission with lower power losses is possible with A. alternating current B. cross…

A: Given: High voltage transmission

Q: Consider a wind turbine which gives maximum output power of 1MW at a wind speed of 15m/s. Choose the…

A:

Q: 1. Summarize the definition of Kirchoff's voltage law.

A: “Since you have asked multiple question, we will solve the first question for you. If you want any…

Q: 01: (A) It is required to generate a high D.C. voltage 40 KV using power transformer (50 KV,1 KVA).…

A: An autotransformer  has a primary winding and secondary winding which is only one single voltage…

Q: A difference between Transmission Substation (TS) and Power Plant Substation (PPS) is that TS has a…

A: Need to find true false

Q: With an AC voltage source of 5.4V and an f = 32000Hz. a) Calculate the Voltage and Current over…

A:

Q: The voltage level of the super high tension cables is kV. 66 11 O 22 132

A: We will write Super tension cable voltage level...

Q: The Auto transformers are used to provide a variable voltage output

A: The Auto transformers are used to provide a variable voltage output.    Is it true or false?

Q: What is HRC fuse : working & it's applications

A: Solve the problem

Q: 2. A 30-volt electromotive force is applied to an LR series circuit in which the inductance is 0.1…

A:

Q: In an Electric circuit: Select one: O a. None of them O b. The algebraic sum of power of all…

A: 1. Total power delivered equal to total power dissipated in a circuit so  the algebraic sum of power…

Q: a) In your own words explain why current is transmitted over long distance as alternating current…

A: consider the given question;

Q: With an AC voltage source of 5.4V and an f = 32000Hz. a) Calculate the Voltage and Current 1,7mH.…

A:

Q: KCL and KVL apply to any circuit we will ever encounter Select one: O True O False

A: In this question we need to verify the given statement is true or false

Q: Draw the AC equivalent circuit for the figure below: 12 V ' 3.9 k2 220 k2 oVo B=120 V; - I

A: We need to find out ac equivalent circuit .

Q: 1. The following constants are for a(1/4) - hp 60-Hz 115-

A:

Q: C1 L1 9.7µ 7.8m V1 C2 R1 5.4р 5.1k AC 0.4 0 R2 =>f = 20 kHz 760

A:

Q: continuity Choose... test ^ V Don Choose... maximize the loading effect minimize the loading effect…

A: To insure that the current is flowing in the circuit, without any alteration, continuity test is…

Q: 1. Compute the power absorbed or supplied by each component of the following circuit. - 8V + 10V…

A: In this question,  Check which components power delivered and absorb.  Power P= VI If power negative…

Q: The Arc Resistance increases as the cross-sectional area of the arc increases. Select one: True…

A: Arc resistance =resistivity×(arc length/arc cross sectionarea).

Q: Your reading material states that the two MAIN factors that determine the amount of current that…

A: Since,we only answer one question at a time. we’ll answer the first question only.Please resubmit…

Q: It is possible to obtain two levels of voltages from two wire DC system. Select one: O True O False

A: This is a good question kn basic power system analysis. Have a look at the below explanation:-

Q: j3Ω -j4 2 12/0° V I j5 Q j6 Q (1, 12Ω ell all

A:

Q: In DC power transmission Ultra High voltage Direct current transmission refers to the voltage level…

A: DC power transmission line

Compensation Techniques

The compensation techniques are the methods that are employed in the electrical control systems to enhance the performance of the system. The performance are generally affected by the factors like lag in the compensating devices, slow response of the system of the components like sensors used in the control system. The basic compensation technique involves lag compensation, lead compensation or the combination of the both.