Let v,(t) = 9cos(2t)V, R1 = 3N, R2 = 82, C1 = 600mF and C2 = 900m F. %3D %3D %3D %3D | + C2 Vs 2i, R1 R2 a. If ZL is a purely resistive load chosen to maximize the average power it receives, the resistor value is ZL = and the resulting average power is P = W. b. If ZL is a complex load chosen to maximize the average power it receives, the load value is 曲 Q ZL = 田+ and the resulting average power is P = W.

Let v,(t) = 9cos(2t)V, R1 = 3N, R2 = 82, C1 = 600mF and C2 = 900m F. %3D %3D %3D %3D | + C2 Vs 2i, R1 R2 a. If ZL is a purely resistive load chosen to maximize the average power it receives, the resistor value is ZL = and the resulting average power is P = W. b. If ZL is a complex load chosen to maximize the average power it receives, the load value is 曲 Q ZL = 田+ and the resulting average power is P = W.

Power System Analysis and Design (MindTap Course List)

6th Edition

ISBN:9781305632134

Author:J. Duncan Glover, Thomas Overbye, Mulukutla S. Sarma

Publisher:J. Duncan Glover, Thomas Overbye, Mulukutla S. Sarma

Chapter2: Fundamentals

Section: Chapter Questions

Problem 2.18P: Let a series RLC network be connected to a source voltage V, drawing a current I. (a) In terms of...

See similar textbooks

Similar questions

Given a sinusoidal voltage source in series with R,L, and C. The sinusoidal frequency is 600 Hz. R=2 Ohms, L=5 milliHenry, C=200 microFarad, V=70sin(wt) volts. Determine the watts and VARs for the capacitor, resistor, inductor, and source. Also find power factor. Given R1=9 Ohms, R2=1 Ohms, L= 3 milliHenries, and a sinusoidal voltage source of 5 volts amplitude and 60 Hz freqency all in series. Determine the voltage across R1: magnitude (volts), frequency (Hz), and phase (degrees).
9.31 Determine the impedance Z, for maximum average power transfer and the value of the maximum power transferred to Z for the circuit shown in Fig. P9.31. j1 Ω 6/0° A Figure P9.31 www 1Ω ZL
Calculate ZL for maximum average power transfer in the circuit, and find the maximum average power delivered to the load. The given answer is ZL=2-j2 Ω, PL=45 W
The 9 Ω resistor in the circuit is replaced with a variable impedance Zo. Assume Zo is adjusted for maximum average power transfer to Zo. 1. a) What is the maximum average power that can be delivered toZo?2. b) What is the average power developed by the ideal voltage sourcewhen maximum average power is delivered to Zo?3. c) Choose single components from Appendix H to form animpedance that dissipates average power closest to the value in part(a). Assume the source frequency is 60 Hz.
Let a series RLC network be connected to a source voltage V, drawing a current I. (a) In terms of the load impedance Z=ZZ, find expressions for P and Q, from complex power considerations. (b) Express p(t) in terms of P and Q, by choosing i(t)=2Icost. (c) For the case of Z=R+jL+1/jC, interpret the result of part (b) in terms of P,QL, and Qc. In particular, if 2LC=1, when the inductive and capacitive reactances cancel, comment on what happens.
Given the voltage v(t) = Vmax cos(ωt + θV) and current i(t) = Imax cos(ωt + θI) signals. (2b-1) Derive the instantaneous power equationp(t). Note: The desired expression will only have cosine functions. (2b-2) Identified the frequency component from p(t) and identifythe radian frequency present on this signal. (2b-3) Identified the DC component of p(t).
If a current 5.0 A lags the applied voltage 230 V by an angle ϕ, it can be resolved into two components, OA in phase with the voltage and OB lagging by 90°. If the phasor diagram in to a circuit possessing resistance and inductance in series, OA and OB must not be labelled and respectively. It has become the practice to say that the power factor is laggingwhen the current lags the supply voltage, and leading when the current leads the supply voltage. This means that the supply voltage is regarded as the reference quantity. (a) A 30 μ F capacitor is connected across the applied voltage, 50 Hz supply. Calculate the reactance of 30 μ F capacitor connected across applied voltage (b) the reactance of the capacitor; (c) the current.
The load impedance ZL for the circuit shown is adjusted until maximum average power is delivered to ZL.1. a) Find the maximum average power delivered to ZL.2. b) What percentage of the total power developed in the circuit isdelivered to ZL?
The impedance ZL in the circuit is adjusted for maximum average power transfer to ZL. The internal impedance of the sinusoidal voltage source is 4+j7 Ω. 1. a) What is the maximum average power delivered to ZL?2. b) What percentage of the average power delivered to the lineartransformer is delivered to ZL?
Q) For the circuit of Fig. 1: . Find the total impedance Z in polar form. b. Draw the impedance. . Find the value of C in microfurads and L in Hz. . Find the current 1 and the voltages Ve, V.. and Ve in phasor form, . Draw the phasor diagram. £ Verify Kirchhof1s voltage law around the closed loop. 2. Find the average power delivered 10 the crcuit. h. Find the power factor of the circuil, asd indicate whether it is leading or lagging . Find the simssoidal expressions for the vollages and current. . Plotthe waveforms for the voltages and currenton the same sct of axcs X, e=113.14 sin(wt+30) V. W=500 rad/sec
A circuit branch is found to have an equivalent impedance of Z=120−j45Ω. It is given that this impedance is a series combination of a 120Ω resistor and another passive component. If the circuit has a sinusoidal voltage source whose frequency is 120 Hz. What is the value of the component in series with the 120Ω resistor? (Note: Express the value assuming a metric scaling of μ(10-6). Provide your answer in decimal form, up to 3 decimal places.)
Find the Norton equivalent in the form of phasors and impedances. Suppose Vf = 100∠0˚ Answer: Zn=93/53 + 34/53jIn=400/370 (19+3j)