In figure 17.16 a conveyor belt is moving a mass M of 30 kg. Cylinders A and B have a diameter of 0.3 m and a mass of 15 kg each. Moreover, each of them has a turning radius of 0.12m. Rollers C,D,E,F and G have a diameter of 75 mm, a mass of 4.5 kg each and a turning radius of 25 mm. What constant torque will increase the velocity of M from 0.2 m/s to 0.9 m/s

In figure 17.16 a conveyor belt is moving a mass M of 30 kg. Cylinders A and B have a diameter of 0.3 m and a mass of 15 kg each. Moreover, each of them has a turning radius of 0.12m. Rollers C,D,E,F and G have a diameter of 75 mm, a mass of 4.5 kg each and a turning radius of 25 mm. What constant torque will increase the velocity of M from 0.2 m/s to 0.9 m/s

University Physics Volume 1

18th Edition

ISBN:9781938168277

Author:William Moebs, Samuel J. Ling, Jeff Sanny

Publisher:William Moebs, Samuel J. Ling, Jeff Sanny

Chapter11: Angular Momentum

Section: Chapter Questions

Problem 76P: The precession angular velocity of a gyroscope is 1.0 rad/s. If the mass of the rotating disk is 0.4...

See similar textbooks

Similar questions

Calculate the m.і. of a thin uniform rod of the mass 100g and length 60cm about an axis perpendicular to its length and passing through (1) its centre and (2) one end.
Zane and Phoebe are sitting on opposite ends of a teeter‑totter that is 4.00 m4.00 m long with the pivot point in the exact center. Zane weighs 433 N433 N and Phoebe weighs 341 N.341 N. What torque does Zane's weight exert?
Calculate the torque (magnitude and direction) about point O due to the force FS in each of the cases sketched in Fig. E10.1. In each case, both the force FS and the rod lie in the plane of the page, the rod has length 4.00 m, and the force has magnitude F=10.0 N. Show complte solution
Suppose you exert a force of 190N tangential to the outer edge of a grindstone (which is a solid disk) with a radius of 1.495m and a mass of 72.5kg. a.) What is the torque τ, in newton meters, you are exerting on the grindstone, relative to the center of mass of the grindstone? b.) What is the angular acceleration of the grindstone α0 , in radians per square second, assuming negligible friction and then what is the angular acceleration of the grindstone αf, in radians per square second, if there is an opposing frictional force of 19.5 N exerted 0.35 m from the axis?
A strut of lengthL = 3.00 m and mass m =16.0 kg is held by a cableat an angle of θ = 30.0°with respect to the horizontalas shown in FigureP8.30. (a) Sketch a forcediagram, indicating allthe forces and their placementon the strut. (b) Why is the hinge a good place to usefor calculating torques? (c) Write the condition for rotationalequilibrium symbolically, calculating the torques around thehinge. (d) Use the torque equation to calculate the tension in the cable. (e) Write the x- and y-components of Newton’ssecond law for equilibrium. (f) Use the force equation tofind the x- and y -components of the force on the hinge.(g) Assuming the strut position is to remain the same, wouldit be advantageous to attach the cable higher up on the wall?Explain the benefit in terms of the force on the hinge andcable tension.
A 150 g uniform rod of length 3.0 m is pivoted about one end. What would be the angular acceleration due to gravity if the rod were held horizontally and released from rest?
A hollow cylinder, of inner radius 0.28m and outer radius 0.41m, is rotating around an axis through the center like a wheel. What would be the torque experienced if it has a mass of 4.00kg and an angular acceleration of 11.11rad/s2?
A ball of putty that has a mass of 753 grams, falls straight down and lands on the outer rim of a rotatingturntable, that has a moment of inertia of 0.051 kg·m^2, a radius of 28 cm, and an angular velocity of 4.8 rad/s.What is the final angular speed of the system?
A 255-lbf block is suspended from an inextensible cable which is wrapped around a drum of 1.75-ft radius rigidly attached to a flywheel. The drum and flywheel have a combined centroidal moment of inertiaI̅= 12 lb . ft . s 2 . At the instant shown, the velocity of the block is unknown directed downward. Knowing that the bearing at A is poorly lubricated and that the bearing friction is equivalent to a couple M of magnitude 65 lb .ft, determine the velocity of the block before it has moved 3.5 ft downward if at S2 speed is 13.5ft/s. (The final answer should be in two decimal places with correct units)
Consider a bar of length 5.5 m, being acted on by three forces and constrained to rotate about its left end. The magnitudes of the first two forces are 19 N and 26 N and the first force is acting on the end of the bar at an angle of 53 What is the torque in newton-meters, due to F1 on this bar relative to the left end? What is the torque in newton-meters, due to F2 on this bar relative to the left end, if this force is acting at the midpoint of the bar? Use a coordinate system with positive directed out of the screen. What is the magnitude of the force F3, in newtons, if the force is a distance 0.25 m from the left end and the bar is not rotating?
Find the net torque on the wheel in Figure P10.23 about the axle through O, taking a = 10.0 cm and b = 25.0 cm. Figure P10.23
What three factors affect the torque created by a force relative to a specific pivot point?