In Figure 4.1, assume that a 21 mm diameter rivet joins the plates that are each 110 mm wide. The allowable stresses are 110 MPa for bearing in the plate material and 61 MPa for shearing of the rivet. Determine (a) the minimum thickness of each plate; and (b) the largest average tensile stress in the plates. CO 1_0 mm width 2_ mm diameter Figure 4.1

In Figure 4.1, assume that a 21 mm diameter rivet joins the plates that are each 110 mm wide. The allowable stresses are 110 MPa for bearing in the plate material and 61 MPa for shearing of the rivet. Determine (a) the minimum thickness of each plate; and (b) the largest average tensile stress in the plates. CO 1_0 mm width 2_ mm diameter Figure 4.1

Principles of Physics: A Calculus-Based Text

5th Edition

ISBN:9781133104261

Author:Raymond A. Serway, John W. Jewett

Publisher:Raymond A. Serway, John W. Jewett

Chapter15: Fluid Mechanics

Section: Chapter Questions

Problem 1CQ

See similar textbooks

Similar questions

A 3m long steel bar whose diameter is 25 mm is compressed by a 25 KN force. If the valueof the modulus of elasticity (E) for steel is 200 GPa, what is the stress developed in the steelbar?
Compute the modulus of elasticity of a copper alloy wire thatstretches 14 mm when subjected to a load of 320 N. The wire is 4 mlong and has a diameter of 1 mm.
Your task is to design a light‐weight tie of length L with a circular cross‐section of radius R. It must carry an axial force F, without stretching by more than δ. You will need to choose the material (with Young’s modulus E and density ρ) and the corresponding crosssection radius to suit your choice of material, i.e. R is a “free variable”,a) Show that the extension of the tie is given by δ = FL/AE, where A = πR2
A 9 16 -in.-diameter steel rod is tested in tension and elongates 0.00715 in. in a length of 8 in. under a tensile load of 6500 lb. Compute (a) the stress, (b) the strain, and (c) the modulus of elasticity, E, based on this one reading. The proportional limit of this steel is 34,000 psi.
The velocity v (m/s) of air flowing past a flat surface is measured at several distances y (m) awayfrom the surface. Use Newton’s viscosity law...to determine the shear stress ? (?/?2) at the surface (y=0). Assume a value for the dynamic viscosity? = 1.8 × 10−5??/?2. How does your answer change if you use more accurate finite differences?
When making a peanut butter sandwich, consider that the bottom piece of bread is fixed. If the knife you use to spread the peanut butter at 0.1 m/s experiences a shearing stress of 41 Pa, what is the viscotity in Pascals times seconds if the thickness of your peanut butter is is 3 cm? Assume that a linear velocity profile develops through the peanut butter layer.
Find the smallest diameter bolt that can be used in the clevis if P =440 000 N and the shearing strength of the bolt is 315 000 KPa.
During heavy lifting, a disk between spinal vertebrae is subjected to a 5000-N compressional force. (a) What pressure is created, assuming that the disk has a uniform circular cross section 2.00 cm in radius? (b) What deformation is produced if the disk is 0.800 cm thick and has a Young’s modulus of 1.50 X 109 N/m2?
Problem 11: Suppose a vertebra is subjected to a shearing force of 540 N.Randomized Variablesf = 540 Nh = 2.9 cmd = 4.3 cm Find the shear deformation in m, taking the vertebra to be a cylinder 2.9 cm high and 4.3 cm in diameter. The shear modulus for bone is 80 • 109 N/m2.
A square flat plate of dimensions 1 m x 1 m is moving with a maximum speed , U causing a fully laminar motion of it inside air ( density :1,2 kg /m3 viscosity :1.5x10-5 m2 /s ) Determine the magnitude of Shearing Stress on the surface of the plate SS=? at plate's trailing edge.ANSWER:SS= 0,0317 Pa
Assume that if the shear stress in steel exceeds about 4.00 x 108 N/m2, the steel ruptures. Determine the shearing force necessary to (a) shear a steel bolt 1.00 cm in diameter and (b) punch a 1.00-cm-diameter hole in a steel plate 0.500 cm thick.
If the velocity distribution over a plate is given by u=2/3 y-y2 in which u is velocity in meter per second at a distance y meter above the plate, determine the shear stress at y=0.75 and y=0.15m. Take dynamic viscosity of fluid as 8.63poises.