In lab, you add 1.985 g salicylic acid to a 125 mL Erlenmeyer flask, as listed in the procedure. You carefully add 4.0 mL acetic anhydride, swirl for a few minutes, then have your TA add 5 drops of sulfuric acid. After completing the synthesis and filtering, you place the crystals to dry on an evaporating dish that weights 21.173 g. After drying, the crystals and evaporating dish weigh 23.472. Calculate the percent yield of aspirin. Insert the value as a percentage, but without the percent sign.

In lab, you add 1.985 g salicylic acid to a 125 mL Erlenmeyer flask, as listed in the procedure. You carefully add 4.0 mL acetic anhydride, swirl for a few minutes, then have your TA add 5 drops of sulfuric acid. After completing the synthesis and filtering, you place the crystals to dry on an evaporating dish that weights 21.173 g. After drying, the crystals and evaporating dish weigh 23.472. Calculate the percent yield of aspirin. Insert the value as a percentage, but without the percent sign.

Chemistry & Chemical Reactivity

10th Edition

ISBN:9781337399074

Author:John C. Kotz, Paul M. Treichel, John Townsend, David Treichel

Publisher:John C. Kotz, Paul M. Treichel, John Townsend, David Treichel

Chapter1: Basic Concepts Of Chemistry

Section: Chapter Questions

Problem 43GQ: Hexane (C6H14, density = 0.766 g/cm3), perfluoro-hexane (C6F14, density = 1.669 g/cm3), and water...

See similar textbooks

Similar questions

In lab, you add 2.018 g salicylic acid to a 125 mL Erlenmeyer flask, as listed in the procedure. You carefully add 4.0 mL acetic anhydride, swirl for a few minutes, then have your TA add 5 drops of sulfuric acid. After completing the synthesis and filtering, you place the crystals to dry on an evaporating dish that weights 21.844 g. After drying, the crystals and evaporating dish weigh 23.108. Calculate the percent yield of aspirin.
When purifying a sample of aspirin that was produced in the lab, the impure aspirin sample should be dissolved in a very cold solvent, so that solid impurities can be filtered and analyzed the next day or the next week. True or False?
The required volume of 28.0 (w/w) % ammonium hydroxide (density =0.899g/mL) diluted it up to 500.0 mL to make 0.250 M NH3 (NH3 RMM=17.03 g/mol) is a. 7.62 mL b. 23.67 mL c. 8.46 mL d. 10.56 mL
Say you glued two samples together; a 4.60 gg sample of acrylic with a density of 1.11 g/mLg/mL and a 1.82 gg sample of Teflon (d = 2.22 g/mL). What is the density of the combined sample? Be careful here and remember the difference between intensive and extensive properties.
A sample sodium is being dried. After 1 hour drying, the mass of the sample was 0.337g. After an additional 30 minutes of drying, the mass of the sample is 0.333g. What is the percent change between the first and second meaasurement? if to be considered "dry", two consecutive measurements must have a percent change <_ +- 1%; is the sample dry?
Your goal is to separate two solids by adding water and then filtering the mixture. What are the final steps of ending up with two separate solids? (select one) a) Use water to wash the solid off the filter paper into the filtrate and evaporate the water from the filtrate. b) Use water to further rinse the solid on the filter paper and collect the filtrate into a new container. c) Scrape the solid off the filter paper into one container and collect the filtrate into a new container. d) Scrape the solid off the filter paper into one container and evaporate the water from the filtrate to isolate the other solid.
After performing precipitation gravimetry, Asta placed the weighing form inside the crucible, heated it, cooled it down, and weighed the crucible with the weighing form and obtained a mass of 23.4120 g. Repeating this cycle continuously gave a mass of 23.2125 g, then 23.1136 g, then 23.1139 g. Which among these masses should he use for his calculations? a. 23.1139 g b. 23.4120 g c. 23.1136 g d. 23.2125 g
rosity is a measure of the void or empty spaces in a material and is a fraction of the volume of voids over the total volume. The density of the solid material used to create 7 pieces of 0.97 cm diameter and 1.14 cm height cylindrical beads is determined to be 1.63 g/mL. These beads were then placed in a flask and was filled to the 40 mL mark with a salt solution. The total weight measured of the beads and the salt solution was 46.86 g. Upon further inspection, it was found that manufacturing defects caused the measured porosity of the beads to be at 32%. Assuming that the solution was able to fully fill the empty spaces inside the beads, calculate the density of the salt solution. Show your solutions in the next item Round your answer to 2 decimal places. Question Porosity is a measure of the void or empty spaces in a material and is a fraction of the volume of voids over the total volume. The density of the solid material used to create 7 pieces of 0.97 cm diameter…
Volume of water in gradudated cylinder:33.8 mL Volume of water plus pellets:41.8 mL Volume of aluminum pellets (mL): Density of aluminum (g/cm3):
It is a type of mixture with particles evenly scattered in a dispersed medium without settling down
Elaina performs the copper cycle lab beginning with 10.00 mL10.00 mL of a 1.57 M Cu(NO3)21.57 M Cu(NO3)2 solution. After drying to constant mass, she recovers 0.741 g0.741 g of copper metal. What is the theoretical yield of copper in grams?
What do you call the liquid that separates from the solids in the a) decantation method? What do you think the color would be? b) in the filtration method? What would the color be?