In micrometer, circular scale is found on the thimble. Select one: True False

Q: Q.6) Complete the following table: No. Part of vernier calliper 1 Main Scale Vernier Scale 3 Screw

A: The main scale reading is that to the left of the zero on the vernier scale. The vernier reading…

Q: What is the name of the size, bigger which should not be the size of a suitable work- piece? 1) the…

A: To select the correct option

Q: Tell us about the tolerance zone in operations.

A: As per given  we have to detail describes about tolerance

Q: Q13) For the following micrometer: a- What is the part diameter?

A: 13

Q: 18 A typical lathe bed is made of a low grade cast iron. Select one: True False

A: We have to find  true /false A typical lathe bed is made of a low grade cast iron.

Q: In a single diameter s and thickn of thickne

A:

Q: During the Brinell harness experiment, it is found that the diameter of indentation diameter is…

A: Answer:

Q: If the main scale reading(mm) and vernier scale reading (division) are 29 and 18 respectively for a…

A: Solution:

Q: 3. a) For an interference fit the hole is smaller than the shaft (True/False) (0.5 Mark) b) The…

A:

Q: If the main scale reading (mm) and vernier scale reading (division) are 49 and 10 respectively for a…

A:

Q: 17q In a lathe machine tool, when the cutting tool moves perpendicular to the axis of rotation of…

A: Lathe machine: Lathe machine is device which used to remove the material from workpiece. By removing…

Q: What type of scale is 10:1? O Full Scale O Enlargement Scale O Reduction Scale

A:

Q: In drawing process, tensile forces are used to reduce the cross section of the workpiece. Select…

A: The drawing process is generally is done at the room temperature. To reduce the required forces, it…

Q: - The corrected length of tape. - The true length of the line.

A:

Q: In a lathe machine tool, when the cutting tool moves perpendicular to the axis of rotation of the…

A: The given statement is ,

Q: To measure the angles, engineer square is used. Select one: True False

A:

Q: s a caliper use to measure inside diameters widths of slots and the like [a)micrometer (b)outside…

A: To determine the correct option.

Q: Suppose you need to drill a 5/8 inch hole, but the set of drill bits is measured in sixteenths of an…

A:

Q: * نقطتان (2 An outside micrometer would be appropriate for measuring which of the :following (two…

A:

Q: The smallest division on the main scale of Vernier calipers is 0.1 cm. Ten divisions of the Vernier…

A:

Q: In order to measure an external tapered angle you must have A. The sine bar and gage blocks B. Two…

A:

Q: The smallest division on the main scale of Vernier calipers is 0.1 cm. Ten divisions of the Vernier…

A: True reading=main scale reading+vernier scale division*least count 10 division of vernier scale=9…

Q: 1. What thickness limit classifies metal as being sheet? 2. What is the decimal size of 14 AWG…

A: Disclaimer: Since you have posted a question with multiple sub-parts, we will solve the first three…

Q: The height (in mm) for a 125 mm sine bar to measure a taper of 27'32' on a flat work piece (correct…

A: Given:Length of sin bar, L=125 mmθ=27o 32'θ=27+3260oθ=27.533o

Q: Outside calipers are used for measuring diameters of holes. Select one: True False

A: Outside calipers are used for measuring diameters of holes. Answer: False

Q: 5. What will be the accuracy of

A: Need to find accuracy .

Q: igh precision in angular measurements can be made using a sine bar. For using a 200 mm sine bar to…

A: Given:Length of sine bar, L=200 mmangle=49o 20'angle=49+2060=49.33oDiameter of rolls, d=35 mm

Q: ___________ tool is used for verifying the flatness of the component.     A. Protractor…

A: Protractor is a device used to measure the angles. Engineers square is a checking tool which is used…

Q: Find force value

A: Given data : Displacement=d Work done=W   Required : Force

Q: Height in mm

A: Given: We have to find the height of the flat workpiece, sine bar is 125 mm which is used to measure…

Q: 6.. Answer fully please

A: Production flow analysis or PFA is a method used for identifying different part families &…

Q: Refer to the Ø.750 dimension. A) Where is the tolerance specified ?…

A: 1—position 2 – the shape of the tolerance zone

Q: Show all

A:

Q: You are given a metal rod, cut to a length of 12 in plus/minus .25in. Then you need to cut off 2 in…

A:

Q: 7. What is a tolerance?

A: Measurement:  It is the numerical quantification of the body or event that is used to compare with…

Q: In uptight drill machine, the power is transmitted from electric motor to spindle with help of belt…

A: Drilling machine is a mechanical equipment used to introduce holes into a specimen which are in…

Q: What is the smallest reading in the main scale a standard Vernier caliper can have?   a. 0.001 cm b.…

A: Measuring distance between two opposite sides of object at laboratory level vernier caliper will be…

Q: If the main scale reading(mm) and vernier scale reading (division) are 16 and 9 respectively for a…

A: Least Count of vernier=(1/20)=0.05mm as a vernier caliper with 20 division on the vernier scale

Q: the minimum metric

A: Given; For the three bolt system shown in the figure,shear yield strength=200 MPaFOS=2The min.…

Q: What tolerance is specified for the width of the groove?

A: Given :-   Bolt Drawing   Find :-  Tolerance of the width of the drawing

Q: A chain and sprocket has a pitch diameter of 9.56-inch and pitch 1/2-in .How many teeth are there in…

A: Given data, D = 9.56 in (D = Pitch diameter ) P= 0.5 in (P = Pitch) Find T = no. Of teeth = ?

Q: Applying finger pressure on the belt near the pulley end is not the correct method to check the…

A: The 'thumb test'  method in which a finger is pressed onto the belt to check whether the belt has…

Q: ving a length of of the specimen?

A: Given data Length of the specimen = 100mm elongation of specimen = 5mm Load on specimen = 10,000N…

Q: Straight gibs are adjusted by screws spaced out along the length of the gib.   Select one: True…

A:

Q: Right the accuracy in millimete

A: The screw gauge with a micrometer. The micrometer screw gauge is used to measure dimensions that are…

Q: The line used to show where a section view is cut is called   A. a section line   B. a hatch line…

A: An engineering drawing is a type of technical drawing which is used by thee industries to convey…

Q: The appropriate diameter is mm.

A: To find  diameter

Q: Vernier Caliper with 50 divisions (lines) on the vernier scale, then the least count is

A:

Q: In drawing process, compressive forces are used to reduce the cross section of the workpiece.…

A: Drawing is a metal forming process used to reduce cross section and increase length of work piece.…