In MS tams project meeting the student audio voce is captured and sampled for 10 second by an 12-bit ADC at a sampling frequency of 30 kHz. The samples are stored on a memory chip. If the sampling frequency is increased by 50% then how long the signal must be sampled to store samples in 1 GB Pen drive

In MS tams project meeting the student audio voce is captured and sampled for 10 second by an 12-bit ADC at a sampling frequency of 30 kHz. The samples are stored on a memory chip. If the sampling frequency is increased by 50% then how long the signal must be sampled to store samples in 1 GB Pen drive

Principles of Information Systems (MindTap Course List)

12th Edition

ISBN:9781285867168

Author:Ralph Stair, George Reynolds

Publisher:Ralph Stair, George Reynolds

Chapter6: Telecommunications And Networks

Section: Chapter Questions

Problem 5SAT

See similar textbooks

Similar questions

A Python code to loop through audio files and extract chroma and MFCC features combined and put them in one data frame.
Use Figma’s wireframe Toolkit to design a wireframe of either or both a MP3 System Music player or even a MP4 Video Player.
given me solution in computer science, . A movie was shot in 150 fps. The movie lasted for 30mins. The movie was played in a vertical and horizontal pixel of 720 × 720 respectively. The bit depth for the video was 16 bit. This same video was shot having an audio sampling rate of 44100 Mhz with an audio bit depth of 32bit. The producer of the video decided to test the quality of the audio for the movie with a surround 5.1 channel audio systemi) Calculate the audio file size in bits and explain its effect on the video file.ii) Calculate the file size of the video in Megabytes (Mb) iii) Calculate the bit rate of the video file and explain the effect of the value on processing of the fil
Please do not give solution in image format thanku Write a suitable software for setup UART Serial Controller that connected to microprocessor at port address A0h as follows [(baud 300 bps(clock 18.432 MHz), data=8 bits parity odd stop bit=two Draw waveform of serial output if data send 67h
Why does boosting a signal reduce the system's dependability?
Write a program that acquires data from a data source and calculates and displays the Discrete FourierTransform associated with that data. In this case, the Arduino will generate a signal, that is sampled by the ADC and then sent to the computerover the serial port. The Arduino code is : int lookup_index = 0; #define SIN_FREQ 100 long sin_freq = SIN_FREQ; #define LOOKUP_ARRAY_SIZE 128UL #define PWM_RESOLUTION 8 #if PWM_RESOLUTION <= 8 #define PWM_t uint8_t #else #define PWM_t uint16_t #endif PWM_t *lookup_array; // lookup array for sin(2pi f t) PWM_t lookup_array1[LOOKUP_ARRAY_SIZE] = { 127, 133, 139, 146, 152, 158, 164, 170, 176, 181, 187, 192, 198, 203, 208, 212, 217, 221, 225, 229, 233, 236, 239, 242, 244, 247, 249, 250, 252, 253, 253, 254, 254, 254, 253, 253, 252, 250, 249, 247, 244, 242, 239, 236, 233, 229, 225, 221, 217, 212, 208, 203, 198, 192, 187, 181, 176, 170, 164, 158, 152, 146, 139, 133, 127, 121, 115, 108, 102, 96, 90, 84, 78, 73, 67, 62,…
In this project, you are required to use MATLAB/Octave/SCILAB software to simulate BPSK modulation waveform. PSK Modulation Phase Shift Keying (PSK) is the digital modulation technique in which the phase of the carrier signal is changed by varying the sine and cosine inputs at a particular time. PSK is of two types, depending upon the phases the signal gets shifted: - Binary Phase Shift Keying: This is also called as 2-phase PSK or Phase Reversal Keying. In this technique, the sine wave carrier takes two phase reversals such as 0° and 180°. - Quadrature Phase Shift Keying: This is the phase shift keying technique, in which the sine wave carrier takes four phase reversals such as 0°, 90°, 180°, and 270°. BPSK ModulatorThe block diagram of Binary Phase Shift Keying consists of the balance modulator which has the carrier sine wave as one input and the binary sequence as the other input. Following is the diagrammatic representation. Please show all the steps and explaination.
It follows a pattern, frame to frame, that allows the demultiplexer to synchronize with the incoming stream so that it can separate the time slots accurately. a. Multiplexer bitsb. Synchronizing bitsc. Framing bitsd. Pulse bits
when we view video on a computer the analog video is digitized and stored in the frame buffer of the video frame grabber card.suppose that a vedio is digitized at integer frame rate size 640*480 pixel and bit depth of 24 bit explain why you dont see a flicker effect on your workstation screen when display this video at NTSC frame rate ?
Consider two raster system with the resolution 640 * 480 and 1280 * 1024. How many pixels could be accessed per second in each of these systems by a display controller that refreshes the screen at a rate of 120 frames per second? What is the access time per pixel in each system?
If you need to design a system for transmitting the output of a minicomputer to a line printer operating at a speed of 30 lines/sec over a voice grade telephone line with a bandwidth of 3 kHz. Assume that the line printer needs 16 bits of data per character and prints out 50 characters per line. What should be the minimum S/N to proceed this transmission?
creating a Simon game using a breadboard, 4 LEDs, 4 Buttons, and an ARM STM 32F103 Nucleo-64. Using Assembly Language. Beginning should have LEDs going back and forth on and off until someone presses the button to play. Start the game by illuminating one LED in the first round. The player should replicate this by pressing the corresponding button, which will activate the matching LED. The player has a restricted time frame to press the button. If the player correctly follows the sequence, proceed to the second round, adding another LED to the sequence. Continue this process up to round 10. The game ends if: 1. you fail. 2. you win. If the user does not successfully mimic the pattern within the allotted time, the Failure sequence will activate, consisting of one LED blinking for three seconds. Subsequently, the player's achieved level will be indicated through a binary pattern displayed on the 4 LEDs. However, if the player successfully completes all 10 rounds, the Game Won sequence…