In powder processing, a cylinder with a diameter of 2 inches and a height of 10 inches is to be made from fine copper powders. A single-action press is used for compaction. If the average density of the green product is 7 g/cm3 at the bottom half of the cylinder, estimate the compaction pressure at the punch surface. Assume no friction between the powders. The coefficient of friction between particles and containers is 0.2.

In powder processing, a cylinder with a diameter of 2 inches and a height of 10 inches is to be made from fine copper powders. A single-action press is used for compaction. If the average density of the green product is 7 g/cm3 at the bottom half of the cylinder, estimate the compaction pressure at the punch surface. Assume no friction between the powders. The coefficient of friction between particles and containers is 0.2.

Principles of Heat Transfer (Activate Learning with these NEW titles from Engineering!)

8th Edition

ISBN:9781305387102

Author:Kreith, Frank; Manglik, Raj M.

Publisher:Kreith, Frank; Manglik, Raj M.

Chapter3: Transient Heat Conduction

Section: Chapter Questions

Problem 3.4P

See similar textbooks

Similar questions

A sectional steel cable of 3.00 cm2 has a mass of 2.40 kg per meter. If the cable is 500 m long hanging on a vertical cliff, how far the cable is stretched due to weighs itself? Known young steel modulus 2.00 x 10¹¹ N/m2 . (b). If there are two climbers hanging on the cable, determine how far cable is stretched. The mass of climbers is 60 kg and 70 kg, respectively.
A tentative rule was given about tipping in Testing Experiment Table 8.4, where if a vertical line passing through the object's center of mass is within the object's area of support the object does not tip. According to the rule, the full box of crackers in the following experiment, which has a width of 13 cm and a height of 20 cm, was seen to tip at an angle of: θc=tan−1(13 cm/20 cm)=33∘θ According to the rule, at what angle will a box with the left half filled with crackers begin to tip? Assume the box is light-weight and that the contents remain in the configuration in
Calculate the young’s modulus from one of these two graphs?
1: A weight of 12 Newtons in hung from a spring. The spring deflects 8 cm. What is the spring constant for this spring? Use Hooke’s Law. How far will the spring deflect if a weight of 20 Newtons is hung from the spring instead? Draw a schematic or diagram. Show all calculations.
How would I find torsion of a hollow foam tube if I'm only given Angle of twist=70 degrees L=20 meters Outside diameter=Do=7 meters Inside diameter=Di=2.5 meters J=(pi/2)(ro^4-ri^4) Note:shear Modulus is unknown because I didn't know what material the foam is
Archimedes established his principle while investigating a suspected fraud in the construction of a crown. The crown was made from an alloy of gold and silver instead of pure gold. Assume that the volume of the alloy was the combined volumes of components (the density of gold is 19.3g⁄(cm^3 ), the density of silver is 10.5g⁄(cm^3 )). If the crown had a weight of 9.81 N in air and 9.10 N in pure water, what percentage of gold (by weight) was it?
Calculate the axial stresses of Galvani pipe, σg.Given the load, P is 12 kN, cross-sectional area of bronze pipe, Ab is 8.92 m2, crosssectional area of galvani pipe, Ag is 1.03 m2, modulus of elasticity of bronze, Eb is 10 MPa and modulus of elasticity of galvani Eg is 60 MPa.
The solid sphere in Fig. is iron (SG ≈ 7.9). Thetension in the cable is 600 lbf. Estimate the diameter of thesphere, in cm.
1. Choose the material that is brittle, a poor thermal conductor, a good thermal insulator, and can withstand high temperatures. a. Ceramics b. Composites c. Polymers d. Metals 2. Choose the substance with the greatest surface tension. a. C9H20 b. C12H26 c. C6H14 d. C24H50 3. Condensation polymers A. Are deposited in molds by condensing vapors B. Also release a small molecule such as water when they are formed C. Usually are made from monomers containing one or more C=C bonds D. None of the Above
The question is related to Modulus of rigidity and is attached as an image.
A copper wire has a radius of 3.5 mm. When forces of a certain equal magnitude but opposite directions are applied to the ends of the wire, the wire stretches by 5.0×10^-3 of its original length. Young's modulus for copper is 11×10^10 Pa What is the magnitude of the force on either end?
Explain the different between non-linearity and hysteresis error (includes diagrams).