In the 3-bit counter circuit in the figure, the initial value of the output is set as Y = Y2Y1Y0 = 111. So what is the value of the output Y after the 3 hour mark?

Q: Using half-adders and full-adders as a block together with external gates, design the following…

A: The given expression is S=K-L+M-N => S=(K+M)-(L+N)   Subtraction in a digital system can be…

Q: How many full adder circuits are needed to add 2 three bit binary numbers. a. 3 O b. 5 C. 2 O d. 6

A: For performing 3bit addition we require 3 full adders  Each bit require one full adder for adding

Q: Using a 4-bit binary counter with parallel load, design a mod-n counter which follows sequence of…

A: The state diagram for the above sequence is shown below:

Q: Q2\What's the truth table for this counter? QD f 10 f 12 13 JO CKI K Q K Q 1-K Q 00 -Q1

A: The circuit diagram of the J-K counter is shown below,

Q: Below are some more logical operations that are handled by systems digital, despite the input being…

A: Given :

Q: Q2/The minimum 4- bit Carry save Adders using to add 6- numbers (5- bit)

A:

Q: BCD is A. Bit Coded digit B. Binary Coded Decimal C. Bit Code digit D. Binary Coded Digit

A: Given BCD

Q: Create a 3-bit counter that counts from 001, 100, 101, 111, 110, 010, 011, 001, and so on. Provide…

A:

Q: A 4-bit parallel adder can add ___________ a. Four bits in sequence b. Two 2-bit binary numbers c.…

A: A 4 bit parallel adder can two 4 bits number is that if A3A2A1A0 is one four bit binary number which…

Q: Design a code converter that converts a decimal digit from BCD to excess-3 code, the input variables…

A:

Q: A 4-bit binary up/down counter is in the binary state of zero. The next state in the DOWNmode is…

A: Given initial state=0 Down counter: It is an sequential circuit which counts in decreasing order of…

Q: ALP for 8-bit addition of numbers in register r2 and r3 and store result in register r5

A: Let the first 8 bit number is x and stored in rx. Let the second 8 bit number is y and stored in ry.…

Q: Simplify the logic expression Z = ( A + B)( B + C)

A: Given data, The value of expression is Z = (A+B)(B+C). Using distributive law the value of Z gets…

Q: A) Using Parallel Adder block diagram to find the result for adding binary numbers A and B, when: A…

A:

Q: sll t2, t0, 6 or t2, t2, t1

A: The answer to the above problem is given below:-

Q: 9. Use 4-bit binary addition to perform 2 + 3. You must first convert the decimal numbers into 4-bit…

A: As per bartleby expert policy, only one question is to be answered.

Q: What is the difference between half and full adders? Draw and explain the circuit diagram to show…

A: Difference between half and full adders Half adders having only two inputs so used to add two one…

Q: Consider the following registers - AX contains 1122h, BX contains 3344h, CX contains 5566h and DX…

A: According to the question,

Q: Switching Theory and Digital Logic design Perform the below operation. 101010112 - 101110002 Show…

A:

Q: (1) Design a 4 bits - Ring Counter using D - FFs. (2) Design a 4 bits - Johnson Counter using D –…

A:

Q: Q4. Starting from an initial value of R in Hex is B2 determine the sequence of binary values in R…

A: The value of the R is binary is,  R=B216R=101100102 On performing the logical shift-left operation,…

Q: [10] Draw a circuit with the following input/output table. [Note: Use only NOT, AND, and OR gates,…

A: The solution is given below

Q: Design a 8-to-3 Priority Encoder with the following priority condition D6>D7>D8>D5>D4>D3>D2>D1>D0…

A: Priority Encoder: A priority encoder or digital encoder is also called a Binary encoder that takes…

Q: If a 10-bit ring counter has an initial state 1101000000, what is the state after the second clock…

A:

Q: Q2) A) Express the decimal number (- 30 ) as an 8-bit number in 2's complement form, and verifying…

A:

Q: 9. The initial value of AX is 01011100, what will be the value of AX after the instruction NOT AX?…

A: In this question,  We need to choose the correct options What is value kr AX after NOT AX…

Q: What is the 2's complement binary representation for the decimal number -96? a.1001 0101 b.1001…

A: This question is from digital electronics. Under which we are going to represent 2's complement of a…

Q: Question1: Read the following table, and design a logic circuit that can convert the binary code…

A:

Q: Using a 4-bit binary counter with parallel load, design a mod-n counter which follows sequence of…

A: Here, for a 4-bit binary counter, number of flip-flop used will also be 4. Also, we will use D…

Q: EXAMPLE : Two 4-bit numbers (1101 and 1011) are applied to a 4-bit parallel adder. The inputs carry…

A: for adder various possible addition bits and their outputs are shown below. bit 1    bit2      carry…

Q: The 3-bit shift register is shifted five times to the right with the serial input being 1011101.…

A: The 3-bit shift register is shifted five times to the right with the serial input being 1011101.…

Q: Design

A:

Q: This is a block diagram of 4-bit adder. Show how binary number 1101+1001 is added. Write the values…

A: The four-bit adder can be implemented using the one-half adder and three full adders.

Q: Design a code converter that converts a decimal digit from BCD to excess-3 code, the input variables…

A: The Code Converter is a tool for converting one binary code to another. Binary codes come in a…

Q: Perform floating point binary addition to the following: A: 1 10000011 10110111010000000000000 B: 0…

A: We need to perform floating-point binary addition to the following: A:…

Q: Give answer correct answer only as soon as possible i will upvote multiple times from my frnds also…

A: B) In n bit parallel adder , n number of full adders are used. Hence for a 14 bit parallel adder we…

Q: 1. In a 4-bit Binary Up-Down counter, Explain why 0 comes after 15 while counting UP and 15 comes…

A: In a 4-bit binary up-down counter, n=4

Q: Problem 3: For 3-bit multiplier given in Figure 3, if A: a2a1a0 = 010 and B:=b2bibo = 010, what is…

A:

Q: What bit pattern is used to represent the decimal value –1110 in 2s complement notation in a…

A:

Q: 1. How many states are there in an 8-bit Johnson counter sequence? 2. Write the sequence of states…

A: Counter is a  sequential circuit made up of flip flop which are connected to count the pulses . It…

Q: When Binary number A=1010 and B=1010, what is the output x in the following diagram? A,A,A, В, В, В,…

A:

Q: - EXAMPLE : Apply each of the following sets of binary numbers to the comparator inputs in Figure…

A:

Q: A comparator circuit has two 2-bit inputs, A(0,1) and B(0,1) [4 total inputs], and three 1-bit…

A:

Q: The Following is a state diagram for a self correcting 4 bit ring counter, what is the illigal…

A: In ring counter the output of last flip flop is connected as input of first flip flop. It is…

Q: i) Convert 100100102 to base 10. ii) Convert F716 to binary. iii) Convert 51738 to Hexadecimal b) i)…

A:

Q: 1. Numbers, Codes, Logic, Circuits a) Convert 101001012 to decimal. b) Convert -6310 to binary using…

A: The solution is given below

Q: Question 1 a) Perform binary subtraction using the 2 complement method. In addition, find decimal…

A:

Q: Q91 For the Logic Circuit shown in figure (6) write the SOP logical expression of the function (F)…

A:

Q: You must only use DIL chips in your design! No logic gates! 3) If you could design only one circuit…

A: According to the question, we need to design a 2-bit adder/subtractor circuit by using 74LS83.

Up-down counter

In digital logic and computing, a counter is a device that stores (and sometimes displays) the number of times a particular event or process has occurred, often in relationship to a clock. A sequential digital logic circuit is the most common type with an input line or clock and multiple output lines. In the binary or binary-coded decimal (BCD) number system, the values on the input line represents a number by several flip-flops connected in a cascaded manner. They are manufactured as separate integrated circuits and are widely used components in digital circuits. These are also a part of larger integrated circuits. These are a specific type of sequential circuit like registers or the value of the flip-flops serving as the output.