In the Atwood machine shown below, m, = 2.00 kg and m2 = 5.60 kg. The masses of the pulley and string are %3D negligible by comparison. The pulley turns without friction and the string does not stretch. The lighter object is released with a sharp push that sets it into motion at v, = 2.15 m/s downward. How far will m, descend below %3D its initial level?

In the Atwood machine shown below, m, = 2.00 kg and m2 = 5.60 kg. The masses of the pulley and string are %3D negligible by comparison. The pulley turns without friction and the string does not stretch. The lighter object is released with a sharp push that sets it into motion at v, = 2.15 m/s downward. How far will m, descend below %3D its initial level?

Glencoe Physics: Principles and Problems, Student Edition

1st Edition

ISBN:9780078807213

Author:Paul W. Zitzewitz

Publisher:Paul W. Zitzewitz

Chapter5: Displacement And Force In Two Dimensions

Section: Chapter Questions

Problem 82A

See similar textbooks

Similar questions

The clutch system is used to transmit torque through a 2-mm-thick oil film with m = 0.38 N?s/m2 between two identical 30-cm-diameter disks. When the driving shaft rotates at a speed of 1450 rpm, the driven shaft is observed to rotate at 1398 rpm. Assuming a linear velocity profile for the oil film, determine the transmitted torque.
In the figure shown below, the 4 forces are being supported by an eyebolt. Determine the force F2 (in kN, roundoff to 2 decimal places) that would produce a net effect on the bolt of R direct pull along the horizontal. F1=4kN R=6kN F3=2.4kN α=30° F4=3.6kN β=30°
A 1.5 kg block and a 2.5 kg block are attached to opposite ends of a light rope. The rope hangs over a solid, frictionless pulley that is 30 cm in diameter and has a mass of 0.75 kg. When the blocks are released, what is the acceleration of the lighter block?
The 4.00 kg block is attached to a vertical rod by means of two strings. When the system rotates about the axis of the rod, the strings are extended as shown in the (Figure 1) and the tension in the upper string is 90.0 N What is the tension in the lower cord? How many revolutions per minute does the system make? Find the number of revolutions per minute at which the lower cord just goes slack.
The wheels,axle, and handles of a wheelbarrow weigh W=56N. The load chamber and it’s contents weigh WL=635N.the drawing shows these two forces in two different wheelbarrow designs. To support the wheelbarrow in equilibrium, the man’s hands apply a force to the handles that is directed vertically upward.consider a rotational axis at the point where the tire contacts the ground, directed perpendicular to the plane of the paper.find the magnitude of the man’s force for both designs.
Consider that instead of the force F, a block with mass m = 0.32 kg (with force F = 3.139 N) and radius R = 13.0cm is attached to the cylinder with a massless string (see Figure). The cylinder is changed to one with the same mass and radius, but a different moment of inertia. Starting from rest, the mass now moves a distance 0.5647 m in a time interval of 0.57 s. Find Icm of the new cylinder.
Which of the following has a greater moment of inertia? a. long, thin leg b. short, fat leg c. short, thin leg d. long, fat leg
A man stands on a merry-go-round that is rotating at 2.13 rad/s. If the coefficient of static friction between the man's shoes and the merry-go-round is ?s = 0.63, how far from the axis of rotation can he stand without sliding? (Enter the maximum distance in meters.) m
An Atwood’s machine consistsof blocks of masses m1 =10.0 kgand m2 = 20.0 kg attached by a cordrunning over a pulley as in FigureP8.46. The pulley is a solid cylinderwith mass M = 8.00 kg and radiusr = 0.200 m. The block of mass m2 isallowed to drop, and the cord turnsthe pulley without slipping. (a) Whymust the tension T2 be greater thanthe tension T1? (b) What is the accelerationof the system, assuming thepulley axis is frictionless? (c) Find thetensions T1 and T2.
A 4.00 kg block is attached to a vertical rod by means of two strings. When the system rotates about the axis of the rod, the strings are extended as shown in (Figure 1) and the tension in the upper string is 90.0 N. I solved the lower cord to equal 41N What is the speed of the block?
A 2.97 gram fine is placed 0.10 m from the centre of a rotating disc. The coefficient of static friction between the fine and the disc is 0.28. What is the maximum speed of rotation, ( at the position of the dime), that the disc can rotate without sliding off?
A block of mass m = 2.90 kg is hanging from a massless cord that is wrapped around a pulley (mass = 5.00 kg) asshown in the figure. The cord does not slip relative to the pulley as the block falls. Find the magnitude of the tension inthe cord. (moment of inertia of the pulley = ½Mr?)