Hand written solution only In the chamber shown, section (1) has adiameter of 4 in., and the flow is 2.8 ft3/s.Section (2) has a diameter of 3.1 in., and theflow velocity (out) is 30.42 ft/s. Compute theflow velocity (in ft/s) of Section (3) if itsdiameter is 1.47 in. Hint: Check whether flowin section (3) is inflow or outflow. Round off totwo decimal places.WaterFo3)

Answered: Image /qna-images/answer/8da7b0d2-0266-4e74-967a-b55303d5abc9.jpg

Answered: In the chamber shown, section (1) has a…

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

1. The figure shows a looping water pipe system. Pressure at A = 85 m and E = 55m. Assume f = 0.053 all pipes. a. Compute the discharge at pipe 1b. Compute the discharge at pipe 2c. Compute the discharge at point B
Water resources engineering Please refer to the attached image. The new cat iron pipe carrying a flow of 0.3 ft3/s becomes divided at point B and rejoins at point C. The elevation at the reservior surface is 1300 feet. The elevation at point D is 560 feet. The pipe diameters and lengths are listed below. What is the pressure at point D? Neglect minor losses. Use the Darcy-Weisbach approach and assume fully turbulent flow. Verify this assumption for one of the pipes. If the assumption is not perfect, iteration is not necessary, just verify and comment. Pipe designation Length (ft) Dia (in) 1 800 6 2 200 8 3 300 4 3 1200 12
Fig D shows a pipe system in parallel with a total flow of 400liters per sec. Determine the flow at the 45cm pipe. For the 45cm pipe use C = 140 and for the 30cm pipe use C = 100
Compute the flow in m^3/s for pipe 1, 2, 3, 4, 5, 6
Water is siphoned from the tank as shown in the figure below. the length of the pipe is 12 m and has roughness ratio (E/D=0.001) a) determine the flow rate and the pressure at point A, stagnation point, neglecting all loses. b) determine the flow rate and pressure at point A, stagnation point, assuming only the major loses are important c) determine the flow rate and pressure at point A, stagnation point, assuming all loses (minor and major) are important.
In the chamber shown, section (1) has a diameter of 4.2 in., and the flow is 2.61 ft3/s. Section (2) has a diameter of 3.2 in., and the flow velocity (out) is 30.67 ft/s. Compute the flow velocity (in ft/s) of Section (3) if its diameter is 1.6 in. Hint: Check whether flow in section (3) is inflow or outflow. Answer is: 64.25
In a pipe 300 mm in diameter, water flows over a length of 300 m, connecting point A, at topographic elevation of 100.0 m, in which the internal pressure is 291 kPa, to point B, at topographic elevation 74 .0 m, where the internal pressure is 334 kPa. Determine the direction of flow. Data: Specific gravity of water = 10 kN/m3. A) from B to A B) There is no drain. 0 C). from A to B For the previous question, calculate the pressure drop between A and B, in meters. ( ) If the flow is equal to 0.18 m3/s, calculate the friction factor of the pipe. ( ) For this same flow rate, calculate the friction velocity. ( )
Water flows from one tank to an adjacent tank through a 60-mm sharp-edged orifice. The head of water on one side of the orifice is 2.9 m and that on the other is 0.7 m. Assuming Cc = 0.63 and Cv = 0.96, calculate the flow rate
A 200mm nonstandard orifice is installed in 250mm pipe carrying water. When the flow is 165lit/sec, the mercury differential gauge reads 50mm. Compute the value of coefficient for the orifice meter.
Determine the flow in each of the pipes shown in the figure. Assume f=0.02 for all pipes. Problem 7-66 with the following conditions: - roughness coefficient for all pipes = 0.05 - elevation B = 100 m
The pressures at the ends of 605m long horizontal pipe flow are 350 kPa and 270 kPa. The pressure at the point between the ends is 300 kPa. The pipe is 305mm in diameter and n=0.018. Find the total headloss, amount of flow, and the slope of the egl.
Water flows through a one-inch diameter pipe at a velocity of 14.4 ft/s. The pipe divides into two 3/4-pipes. Find the flow rate in the two 3/4-inch pipes.

SEE MORE QUESTIONS

Recommended textbooks for you

Structural Analysis

Civil Engineering

ISBN:

9781337630931

Author:

KASSIMALI, Aslam.

Publisher:

Cengage,

Structural Analysis (10th Edition)

Civil Engineering

ISBN:

9780134610672

Author:

Russell C. Hibbeler

Publisher:

PEARSON

Principles of Foundation Engineering (MindTap Cou…

Civil Engineering

ISBN:

9781337705028

Author:

Braja M. Das, Nagaratnam Sivakugan

Publisher:

Cengage Learning

Structural Analysis

Civil Engineering

ISBN:

9781337630931

Author:

KASSIMALI, Aslam.

Publisher:

Cengage,

Structural Analysis (10th Edition)

Civil Engineering

ISBN:

9780134610672

Author:

Russell C. Hibbeler

Publisher:

PEARSON

Principles of Foundation Engineering (MindTap Cou…

Civil Engineering

ISBN:

9781337705028

Author:

Braja M. Das, Nagaratnam Sivakugan

Publisher:

Cengage Learning

Fundamentals of Structural Analysis

Civil Engineering

ISBN:

9780073398006

Author:

Kenneth M. Leet Emeritus, Chia-Ming Uang, Joel Lanning

Publisher:

McGraw-Hill Education

Sustainable Energy

Civil Engineering

ISBN:

9781337551663

Author:

DUNLAP, Richard A.

Publisher:

Cengage,

Traffic and Highway Engineering

Civil Engineering

ISBN:

9781305156241

Author:

Garber, Nicholas J.

Publisher:

Cengage Learning

SEE MORE TEXTBOOKS