In the circuit below, when a 2.2KN load is connected to the output, find the value of the currentflowing through the R resistor (IR), the current passing through the zener diode (Iz) and the loadcurrent value (IL).SigortaT1Dr-De 1N40010,1AREGOLATORD220VACVa-20VVsACVa2200DeVi-13V15V4700uFIN47448NominalTestMaximum Dynamic ImpedanceMaximum ReverseZenerCurrentLeakage CurrentVoltage)Vz @ IzTIZTZT @ IzT ZZK @ IzKIZKIRTestVoltage VRVmAΩΩmAµAV1517147000.2511.4llle

Answered: Image /qna-images/answer/b343e6f2-86e1-41dd-8457-f856f3ef4c47.jpg

In the circuit below, when a 2.2KN load is connected to the output, find the value of the current flowing through the R resistor (IR), the current passing through the zener diode (Iz) and the load current value (IL). Sigorta Dr-De 1N4001 T1 0,1A REGOLATOR 220V AC Va-20V Va AC 220 De Vi-15V 15V 4700uF IN4744A Nominal Test Maximum Dynamic Impedance Maximum Reverse Zener Current Leakage Current Voltage1) Vz @ IzT IZT ZT @ IZT ZZK @ IzK IZK IR Test Voltage VR V mA Ω Ω HA V ellle

In the circuit below, when a 2.2KN load is connected to the output, find the value of the current flowing through the R resistor (IR), the current passing through the zener diode (Iz) and the load current value (IL). Sigorta Dr-De 1N4001 T1 0,1A REGOLATOR 220V AC Va-20V Va AC 220 De Vi-15V 15V 4700uF IN4744A Nominal Test Maximum Dynamic Impedance Maximum Reverse Zener Current Leakage Current Voltage1) Vz @ IzT IZT ZT @ IZT ZZK @ IzK IZK IR Test Voltage VR V mA Ω Ω HA V ellle

Introductory Circuit Analysis (13th Edition)

13th Edition

ISBN:9780133923605

Author:Robert L. Boylestad

Publisher:Robert L. Boylestad

Chapter1: Introduction

Section: Chapter Questions

Problem 1P: Visit your local library (at school or home) and describe the extent to which it provides literature...

See similar textbooks

Similar questions

Attampet with only two: 1: Prove that the dynamic resistance of diode is ra=26mv/Ip. 2:Prove that the ripple voltage of HWR is Viru=V+Vde and the ripple factor of HWR 121%, u=40.5%. 3: Using silicon diode design a clamper that will produce output V-20Sin wt+10 (v) when the input voltage is Vo=20Sin wt-10 (V).Draw the circuit diagram and the input and output signals. 4:The 6-V zener diode has a maximum rated power dissipated of 690 mw.Its reveres current must be at least 3mA to keep it in breakdown. Find a suitable value for Rs if V; can vary from 9v to 12v and Ri. can vary from 5000 to 1.2KO.
for the circuit shown in figure , a silicon is used B=40 find the value of Vo and the regiion of operation for: A) V=15v B) V=30v
The step up chopper has R=20 ohm and out put voltage is 120V. The source voltage is 40V DC . The load inductance is 0.2mH. If the chopper frequency is 4KHZ find1- the duty cycle2- the average value of source current3- TON4- Imax5- Imin6-The average value of diode current
The data sheet of a JFET gives the following information: IDSS = 3 mA, VGS(off)= - 6 V, and gm(max)= 5000 . For VGS = - 4 V. find the drain current.
Question 6 In the boost converter, we know the boost now is working at the critical state from CCM to DCM condition, i.e., the minimum inductor current is 0. If the average output current is 1 A and the duty cycle is 0.4, what is the peak current of the diode in this converter? a)3.33A b)6.66A c)1.78A d) 4.82 A Full explain this question very fast solution sent me step by step
This is a half-wave rectifier with a filter capacitor & a 60Hz ACE line input of R = 120Ω, C = 470µF. 1.) Where does the resistor comes from in segment 1 and 2? a. Capacitor, Diode b. Diode, Diode c. Diode, Capacitor d. Capacitor, Capacitor 2.) Assuming that the peak voltage Vmax across the capacitor is 16V and the capacitor discharges into the resistor for 12msec. (1) Determine the time constant of the circuit (in ms) during the discharge? (2) Determine the voltage Vmin (in volts) across the capacitor.
For the circuit in the figure, let V input = 8V, Ri = 12ohms, RL = 10ohms, and VZ = 3.3V. Determine the voltages and currents of the resistors and the current of the zener diode.
Thank you for your help Assume a diode p-region is doped NA= 5 x 1015 cm-3 and the diode n-region is doped ND= 8 x 1016 cm-3. Compute VJ (Diode turn-on voltage). Repeat for NA= 3 x 1018 cm-3 and the diode n-region is doped ND= 1 x 1017 cm-3. Assume ni= 1.0 x 1010 cm-3.
The anode of a diode is connected to one terminal of a 1-KΩ resistor. The other terminal of the resistor is connected to the ground and the negative terminal of a 12-volt DC source is also grounded. The three components are connected in series. How much is the load current with the ideal diode?
Which of these two is valid for an ideal diode and why? 1.) ID = 0 mA and VD = -2V 2.) ID = 4 mA and VD = -2V
For the input voltage Vi in the figure, we calculate the output voltage as Show by drawing over the period. (Note: used diode is silicon diode, ideally will not be evaluated.)
Design such a power supply with an input Voltage ranging from 10V to 15 V, and a limiting Resistor of 4.0 kΩ. Specifications of the Zener diodes are; VBr is 8 V and RZ is 100Ω. Your task is to obtain regulated output Voltage within the input voltage range.