Please circle your answers to each part. Thank you!! In the circuit shown in (Figure 1), the capacitors are all initially uncharged and the battery has noappreciable internal resistance. Assume that E = 49.0 V and R = 21.0 Q.20.0 pFRH10.0 pF30.0 pF40.0 pFA. After the switch is closed, find the maximum charge on the 10.0 pF capacitor.Express your answer inpicocoulombs.B. After the switch is closed, find the maximum charge on the 20.0 pF capacitor.Express your answer inpicocoulombs.C. After the switch is closed, find the maximum charge on the 30.0 pF capacitor.Express your answer inpicocoulombs.D. After the switch is closed, find the maximum charge on the 40.0 pF capacitor.Express your answer inpicocoulombs.E. After the switch is closed, find the maximum potential difference across the 10.0 pF capacitor.Express youranswer in volts.F. After the switch is closed, find the maximum potential difference across the 20.0 pF capacitor.Express youranswer in volts.G. After the switch is closed, find the maximum potential difference across the 30.0 pF capacitor. Expressyour answer in volts.H. After the switch is closed, find the maximum potential difference across the 40.0 pF capacitor. Expressyour answer in volts.After the switch is closed, find the maximum reading of the ammeter A. Express your answer in amperes.I.

As per our policy, i am attempting first 3 questions. Given data, E=49.0 VR=21.0 Ω

In the circuit shown in (Figure 1), the capacitors are all initially uncharged and the battery has no appreciable internal resistance. Assume that E = 49.0 V and R = 21.0 Q. 20.0 pF R 10.0 pF 30.0 pF 40.0 pF

In the circuit shown in (Figure 1), the capacitors are all initially uncharged and the battery has no appreciable internal resistance. Assume that E = 49.0 V and R = 21.0 Q. 20.0 pF R 10.0 pF 30.0 pF 40.0 pF

Delmar's Standard Textbook Of Electricity

7th Edition

ISBN:9781337900348

Author:Stephen L. Herman

Publisher:Stephen L. Herman

Chapter20: Capacitance In Ac Circuits

Section: Chapter Questions

Problem 2PA: You are working in an industrial plant. You have been instructed to double the capacitance connected...

See similar textbooks

Related questions

Q: What will be the resultant capacitance of the given combination? 1mF 2mF 3mF 4mF = 5 mF

A: Given data, Circuit diagram is given as,

Q: 1 pF 3 uF 100 V Ο Α) 25 μC Ο Β) 20 μC O0 100 μC O D) 10 μC E) 50 u

Q: 1) In capacitors, the time constant determines the discharge rate. True or False 2) AC currents…

A: (1) in capacitors, the time constant determines the charging rate. Hence given statement is FALSE.…

Q: A capacitor of 0.01 μF (micro farad) was charged by connecting in series with a 100 k V resistor to…

Q: Calculate the Current taken by a 300 μf capacitor when connected to a 120 v, 20 Hz supply.

A: We have to find reactance then using simple ohm we can find current.

Q: 3. In Figure 11, each capacitor has C= 5.20 µF and Vab = +25.0 V. (a) Calculate the charge on each…

A: The solution is given below

Q: Capacitor and resistor of 10 µF and 0.7 MN are connected in series across a d.c supply voltage of…

Q: Calculate the current drawn from a 50 V, 60Hz supply by an 80 mH inductor? O 1.66kA O 1.66A O 166A O…

A: Given, Voltage, Vs = 50 V Frequency, f = 60 Hz Inductance, L = 80 mH

Q: D Question 6 What capacitance value (in microFarad) should be used to make PF = 1 R 100 V 400 L 150m

Q: O If the capacitor of Figure (2) has the value df on the circuit? Determine the time constant. Volt…

Q: Three capacitors are connected in parallel and have the following voltage ratings: C1 = 32 uF with…

A: The solution is given below

Q: A capacitor of value 100uF is connected across a 200 V, 50 Hz supply. Calculate : (i)reactance of…

A: We have an capacitor with, C = 100 μF = 100 * 10-6 F Voltage (V) = 200 V Frequency (f) = 50 Hz…

Q: Att = 0, a 6.00 V battery is connected in series with a 120 mH inductor and a total of 25 Q…

Q: For the circuit in Figure, determine: (a) the total capacitance, (b) the total charge 120 V 2 μF 4…

A: Given, Circuit is,

Q: a) Determine the values of R and C needed to replace the capacitors and resistors of the left…

Q: 1. In five time constant, the inductance current is equal to (a) (E/R) e 5. A capacitor that stores…

Q: If you have circuit with two capacitors C1=400 uF, C2= 200uF and voltage 120 V. Calculate

A: The solution can be achieved as follows.

Q: How long will it take for the capacitor in the circuit below to charge to what wou be considered…

A: In this question, choose the correct option. We know charge on the capacitor Q= CV. Time Constant…

Q: What is the current through a 10 uF capacitor connected across a 120 V, 60 Hz supply? O a) 31.8 kA O…

Q: For Figure 2, which of the following capacitors are called as bypass capacitors? What is the…

A: The capacitor which is connected parallel to source resistance Cs is by pass capaa

Q: 12 Capacitance sensor can measure very small displacement. It can be formed by varying a. Separation…

A: Note: please upload only one question at once so you will get better answer and explanation.

Q: a) Find the equivalent capacitance and the total charge for the circuit in Figure 2. 20 µF 60 uF 100…

A: If two capacitors C1 , C2 are connected in series than equivalent capacitance is C1×C2C1+C2 If two…

Q: In a given parallel plate capacitor with a stored energy of " W" Joules, if the capacitance value is…

Q: QUESTION 2 Initially, the capacitors in the circuit in Figure 2 are uncharged. After the switch is…

Q: Consider the circuit shown below. (The capacitors are initially uncharged.) R C1 R C2 S lust after…

Q: Three capacitors are connected in parallel and have the following voltage ratings: C1 = 32 uF with…

Q: The voltage across a 5uF capacitor is v(t)= 10 cos 5000t V. Calculate the current through it.

Q: A pure 20 mH inductor is connected to a 30 V, 50 Hz supply. Calculate the reactance

Q: Three capacitors are connected in parallel and have the following voltage ratings: C1 = 32 uF with…

Q: If Vab=10 Volts according to the circuit in the figure, how many joules is the work done during the…

A: First simplify the circuit then find voltage across the 6uF capacitor. Then by using formula we can…

Q: For the circuit shown in Figure 1, determine: i. The total capacitance of the circuit ii. The total…

Q: a 100-uF capacitor is i(t)=50sin(120πt)50sin(120πt) mA. Calculate the voltage across it at t=1ms and…

Q: For the given circuit below calculate i) the total capacitance of circuit ii) the total charge in…

A: The given circuit is,

Q: b) For the circuit as shown in figure 2, calculate the equivalent capacitance between a an 25 μF 25…

Q: c) Some capacitors are marked 45micro farad save working voltage 25V. On a circuit diagram show how…

Q: Three capacitors are connected in series to a 0.04 kV supply, if the first capacitor is 75 µF and…

Q: a) Find the equivalent capacitance and the total charge for the circuit in Figure 2. C2 0.001 uF C3…

Q: refer to attached schematic diagram: How much time is needed to discharg the voltage of the…

Q: When charging a capacitor: O the current in the circuit decreases exponentially with time O the…

A: Capacitor charge slowly with time.

Q: 20. An inductor has a maximum current of 4 amperes, When power is interrupted, how much current will…

A: We need to find out the current for inductor at given time instant .

Q: What will be the resultant capacitance of the given combination? 1mF 2mF 3mF=4mF = 5 mF

Q: (a) Calculate the energy stored in each capacitor in Figure 2 under DC conditions. 4 mF 8 mF 1) 9A(…

A: Note : According to the guidelines of the company if the questions are of different we supposed to…

Q: II. Calculate the values asked in the following questions with the given circuit diagram. Determine…

A: Given, And Vt=5 V

Q: Figure < 1 of 1 3.00 μF 5.00 μF be 6.00 μF

A: Given Voltage across ab terminal Vab = 23.5 V In capacitor charge Q =CV Voltage across 3 μF…

Q: A 50 and 100 microfarad capacitors are connected in series and across 100sin(w+30) voltage. Write…

Q: -) (1) (ii) (iii) F 47μF 47μ Figure 1.1. Figure 1.1 shows an electrolytic capacitor. What…

A: Brief description: Energy stored in the capacitor is directly proportional to capacitance and…

Q: Determine the total charge on the capacitors. Write down only the number. Use microCoulombs as a…

A: Given,

Q: A 20-ohm resistor and a capacitor are connected in series with a battery of 60 volts. At t 0, there…

Q: A 100 μF capacitor that had been charged to 30 V is discharged through a resistor. The figure…

A: Given, Capacitance, C=100 μF Initial voltage, V0=30 V Capacitor is discharged through a resistor.…

Concept explainers

Thermistors

A thermistor is a special type of resistor whose resistance is more temperature-dependent than standard resistors. The resistance of the thermistor decreases with increasing temperature. This is the basic principle of thermistors. This allows the thermistor circuit to detect very small temperature changes that cannot be observed with the Resistance temperature detectors (RTDs) or the thermocouples. Since the resistance of a thermistor is temperature dependent, it can be connected to an electrical circuit to measure body temperature. This high sensitivity to temperature changes makes thermistors very useful for accurately controlling and calibrating temperature measurements. In general, resistance increases with increasing temperature in most metals, but thermistors react negatively.

Question

Please circle your answers to each part. Thank you!!

In the circuit shown in (Figure 1), the capacitors are all initially uncharged and the battery has no
appreciable internal resistance. Assume that E = 49.0 V and R = 21.0 Q.
20.0 pF
R
H
10.0 pF
30.0 pF
40.0 pF
A. After the switch is closed, find the maximum charge on the 10.0 pF capacitor.Express your answer in
picocoulombs.
B. After the switch is closed, find the maximum charge on the 20.0 pF capacitor.Express your answer in
picocoulombs.
C. After the switch is closed, find the maximum charge on the 30.0 pF capacitor.Express your answer in
picocoulombs.
D. After the switch is closed, find the maximum charge on the 40.0 pF capacitor.Express your answer in
picocoulombs.
E. After the switch is closed, find the maximum potential difference across the 10.0 pF capacitor.Express your
answer in volts.
F. After the switch is closed, find the maximum potential difference across the 20.0 pF capacitor.Express your
answer in volts.
G. After the switch is closed, find the maximum potential difference across the 30.0 pF capacitor. Express
your answer in volts.
H. After the switch is closed, find the maximum potential difference across the 40.0 pF capacitor. Express
your answer in volts.
After the switch is closed, find the maximum reading of the ammeter A. Express your answer in amperes.
I.

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

This is a popular solution!

SEE SOLUTION Check out a sample Q&A here

Step 1

VIEW

Step 2

VIEW

Step 3

VIEW

Trending now

This is a popular solution!

Step by step

Solved in 3 steps

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, electrical-engineering and related others by exploring similar questions and additional content below.

Similar questions

You are working in an industrial plant. You have been instructed to double the capacitance connected to a machine. The markings on the capacitor, however, are not visible. The capacitor is connected to 560 volts and an ammeter indicates a current of 6 amperes flowing to the capacitor. What size capacitor should be connected in parallel with the existing capacitor? What is the minimum AC voltage rating of the new capacitor? What is the minimum DC voltage rating of the new capacitor? What is the minimum KVAR size that can be used in this installation?
You find that a 25-F capacitor connected to 480 VAC is defective. The storeroom has no capacitors with a 480-VAC rating. However, you find two capacitors rated at 50 F and 370 VAC. Can these two capacitors be connected in such a manner that they can replace the defective capacitor? If yes, explain how they are connected and why the capacitors will not be damaged by the lower voltage rating. If no, explain why they cannot be used without damaging the capacitor.
What is the unit of measurement for the strength of a capacitor? microamp microtorque microfarad microwatt
A pure capacitive circuit is connected to a 480-volt, 60-Hz power source. An ammeter indicates a current flow of 24 amperes. The circuit current must be reduced to 16 amperes by connecting a second capacitor in series with the first. What is the value of the existing capacitor? What value capacitor should be connected in series with the original capacitor to limit the circuit current to 16 amperes?
You are an electrician working in an industrial plant. You discover that the problem with a certain machine is a defective capacitor. The capacitor is connected to a 240-volt AC circuit. The information on the capacitor reveals that it has a capacitance value of 10 mF and a voltage rating of 240 VAC. The only 10-mF AC capacitor in the storeroom is marked with a voltage rating of 350 WVDC. Can this capacitor be used to replace the defective capacitor? Explain your answer.
For residential water heaters, the Consumer Product Safety Commission suggests a maximum temperature setting of ___________ F (_____________ C). Some states have laws stating a maximum temperature setting of ____________ F (________________ C).
An emf of V=70.0 volt, a resistor R=80.0 KΩ and a capacitor C=2500 µF are connected by a switch as shown in the figure. At t= 0 s the switch is closed. The time in seconds it takes for the capacitor to store 80.0 mC of charge is:
For the circuit in Figure 1: a) . Determine the equivalent capacitance of the system. b) If the potential difference between point a and b is 100 V, determine the energy 10 μF capacitor stored. c) If all the capacitors initially had air and now they have been put as material graphite dielectric (k = 12.5), what is the difference in charge of the 6 μF capacitor near point b?
Show complete and detailed solution. Explain answer. A decaying emf E = 200e-5t connected in series with a 20 ohm resistor and 0.01 farad capacitor. Assuming Q = 0 at t = 0, plot the charge and current as a function of time. Show that the charge reaches a maximum, calculate it and find when it is reached.
1) In the figure attached, the battery has emf 92.0 V and negligible internal resistance. R2 = 2.00 Ω, C1 = 5.00 μF, and C2 = 8.00 μF. After the capacitors have attained their final charges, the charge on C1 is Q1 = 21.0 μC. a) What is the final charge on C2 and the resistance of R1?
For the circuit shown in figure, C=6.00 µF, e=100 V, and R=500 ohm. After having been at contact a for a long time, the switch throw is rotated to contact b. Find (a) the charge on the capacitor just as the switch throw is moved to contact (b) the current just after the switch throw is rotated to contact (c) the time constant of this circuit (d) How much charge is on the capacitor 6.00 ms after the switch throw is rotated to contact b.
When the switch is in position 1, the circuit will charge the capacitor. Determine the equations for v(t) and i(t) for the charge phase and determine the voltage and current at time, t = 31 ms, in the charge phase.