Answered: In the experiment 1, the values are…

In the experiment 1, the values are tabulated, find the load power factor. VL in Volts W, in watts W2 in watts 220 111 228

Delmar's Standard Textbook Of Electricity

7th Edition

ISBN:9781337900348

Author:Stephen L. Herman

Publisher:Stephen L. Herman

Chapter23: Resistive-inductive-capacitive Series Circuits

Section: Chapter Questions

Problem 7PP: Is the power factor in Question 6 a leading or lagging power factor? Explain your answer.

See similar textbooks

Related questions

Q: In the circuit shown below, what would be the wattmeter reading? 200 V {4 + j3} Ω 50/5 A CT m www.m…

A: Given circuit, Voltage across potential coil is equal to source voltage, Vpc=Vs=200 V. Impedance,…

Q: What is the MW indicated when the wattmeter reads 750 watts of a 230 kV substation, the PT ration is…

A: It is given that: Wattmeter reading=750 WPT Ratio=1000/1CT Ratio=1200/5Potentital goint into…

Q: - previous 4- If VI 400V and the wattmeter read 800W at no load test then the value of Ro is b)40052…

Q: Calculate the current drawn by the load and the power factor.

A: For the given 3 phase system we need to find a current and power factor of load

Q: 10. A 110-Volt AC line feeds two circuits in parallel. The currents are (2.2 - j6.5)A and (1.8 –…

A: Since you have asked for question 10 . So we are providing solution for question 10 . This question…

Q: What is the MW indicated when the wattmeter reads 750 watts of a 230 kV substation, the PT ration is…

A: Given parameters are: Wattmeter Reading, W=750W PT Ratio= 1000/1 CT Ratio =1200/5

Q: Using the formula for power P = VI, find P in watts and milliwatts when V = 900 mV and I = 850 mA

A: Power is the multiplication of the voltage and current it measures in Watt Given: V = 900 mV = 900…

Q: Z1 V1 ЗРН Y 120V 60HZ 1kQ 1mH 1uF Figure 1.1

A: The given system is balanced so we can convert three phase system to single phase equivalent circuit…

Q: What is the reading of the wattmeter in the network

A: To Find the reading of the watt meter in the network

Q: Calculate the demand factor, if the maximum demand is 2800 kW and connected load is 3000 kW.

Q: In figure given below, V, = 1/2 V; = 18V, V, = 25V, V. = 30V. The applied voltage must then be equal…

Q: If both meters read equal and one is negative in the two element wattmeter, then the value of power…

A: Let the one wattmeter is W1 and the another wattmeter is W2

Q: At a substation, the PT ratio is 1000 and the CT ratio is 2000/5. The potential going into the…

A: Given: PT ratio: 1000 CT ratio: 2000/5 The potential at wattmeter: 115 V Reading of wattmeter: 800 V…

Q: A load consumes 50kW and 20 KVAR. What is the power factor at the load terminals?

Q: Q1) Find the value of (Ix) and find the power supply by 42 and 52 using (K.V.L) ? in O 2IX

A: Since you have asked multiple questions in a single request, we will be answering only the 1st…

Q: (a) Efficiency when supplying half full load at a power factor of 0.7. (b) Load corresponding to…

Q: 10i1 i, 50 a 25V Ž500 Ž1000 RL b

A: According to the maximum power transfer theorem the value of the load resistance should be equal to…

Q: es the wattmeter has resistance and resistance halwlate the Percentage error if the Wattmeter is So…

A: When the current coil is connected near to the load then error in power measurement =I2 RC When the…

Q: The connected load of a consumer is 1.5 kW and maximum demand is 4.5 kW. What is the demand factor…

A: Need to find the demand factor

Q: The figure below shows a semi-log plot of the power consumed in the load as a function of the load…

A: In a semi-log plot, each vertical line intersecting at the horizontal axis represents 1/10th of the…

Q: what is the power factor of the load on a 460volts, 3phase system if the ammeter indicates 100amps…

Q: A load absorbs 3 A with 75 V applied. If the load power factor is 0.6 late, find the power…

A: The complex power in a sinusoidal system is defined as the product of rms value of applied voltage…

Q: If one meter read twice the other in the two element wattmeter, then the value of power factor is…

A: Let one wattmeter measures power = p1 Another wattmeter measures power =p2 From the given statement…

Q: From the circuit diagram of power measurement using two wattmeter for delta connected load in…

A: Two wattmeter connection is used for measuring the three phase power of circuit This two wattmeter…

Q: For the following circuit in the figure below, find the power ( in units of Watt) delivered to the…

Q: 50 V= 100Vrms f = 1khz 1uF

Q: A generating station has an overall efficiency of 20% and 3.5x 10 of fuel is burnt per kwh by the…

A: given problem is very simole and based on power system subject. Option C is correct. Dear leaener…

Q: If the real power drawn by the device is 4.9 kW, with a power factor angle 0.85, what is the…

Q: Given DC voltage and AC sinewave voltage in series, what would be the total power delivered to a…

Q: 2. For the figure below, determine the (a) Power dissipated in the load (b) Wattmeter reading 1=20 A…

Q: The power produced using Osterwald's method if the irradiance is 650 W/m² and the ambient…

A: Given:radiance=650 W/m2ambient temperature=20°C, then Tcell=45°

Q: 8. A factory has a maximum demand of 500 kW, the load factor being 60% during working hours. The…

A: The solution can be achieved as follows.

Q: From the experiment 2, the two wattmeter method is used to measure the power. In that current coil…

A: wattmeter has two coils namely current coil and pressure coil. For power measurement current coil…

Q: What is the total power consumed by the load when the reading of wo watt meters are 5kW and –0.5 kW?…

A: In this question, We need to choose the correct options What's the total power consumed by the load…

Q: In the circuit shown below, what would be the wattmeter reading? 200 VI (4 + j3) Q 50/5 ACT my www.m…

A: In this question, We need to determine the reading of the wattmeter as shown the circuit. Reading…

Q: power factor is measured in Select one: O a. no unit b. watt C. VA d. VAR

A: Power factor: It is the ratio of active power P to the apparent power S. It is denoted by cosθ. So,…

Q: A 300 V, 5A, 0.2 pf low power factor wattmeter is used to measure the power consumed by a load. The…

A: Given values are - Vt=300VoltIt=5Acosϕ=0.2Total division=150Reading division=100

Q: factor is 0.66 leading, what will be the reading of each wattmeter? For what power factor will one…

Q: In the circuit shown in figure, if power consumed by 50 resistor is 10 W. The power factor of the…

A: Solution: The power consumed by the 5-ohm Resistor=10 W P5 Ω=I2R10=I2×5I=105I=2 A Total power…

Q: b +CC W1 +PC- 6V 3A 15V + PC- +CC W2 Wattmeter W1 reads 75 W Wattmeter W2 reads 60 W Determine the…

A: Given in question, In the above figure, wattmeter W1 reads 75 W, wattmeter W2 reads 60 W. It is…

Q: 4. For the figure below, determine the (a) Power dissipated in the load (b) Wattmeter reading 1-20 A…

A: The power dissipated in the load is given by: Pload= I2xR…

Q: In the experiment 1, the values are tabulated, find the load power factor. Vį in Volts W, in watts…

A: Since the values of W1 and W2 are given and value of power factor is asked it is two wattmeter…

Q: Two wattmeter connected to measure power read W1=30kW and W2 =55kw. What is the power facto

Q: Q1. Answer three from four: 1. Does the efficiency vary with power factor? If yes, why.

A: As per the honour code I will answer only the first question. Kindly repost the other questions…

Q: A power station has a maximum demand of 15000 kW. The annual load factor is 50% and plant capacity…

Q: Problem 1: Write the Node Voltage Equation and determine the value of V. A. 44 Volts + V. - v, B. 45…

Q: Predict power consumption for a month if the temperature is 770F

A: The power system has to transmit power from the generation side to the load side. For this purpose,…

Q: . For the figure below, determine the (a) Power dissipated in the load (b) Wattmeter reading | 1=20…

A: Given data: current through load I = 20 A Load R = 2 ohm

Q: power factor is measured in Select one: a. VAR b. no unit c. watt d. VA

A: Power factor is defined as the ratio of true power to apparent power.

Q: What is the efficiency of the turbine if Power of the wind is 120.2 W and power of turbine is 402.2…

A: Efficiency of turbine= =((power of wind)/(powee of turbine))*100% Given: power of…

Question

In the experiment 1, the values are tabulated, find the load power factor.
VL in Volts
W, in watts
W2 in watts
220
111
228

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

SEE SOLUTION Check out a sample Q&A here

Step 1

VIEW

Step 2

VIEW

Step by step

Solved in 2 steps

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, electrical-engineering and related others by exploring similar questions and additional content below.

Similar questions

A. a heater is connected to voltage source of 250 V and absorbs P= 1000 W. S= 1400 VA .What is the Power factor for this heater. What is the Impedance of the heater?
For the following network find a) Isb) PT, QT, ST and PFTc) Draw power triangle d) Raise the power factor to unitye) Compute Is after raising the power factor
A generation station of 6 kw has a load factor of 0.7 and plant capacity factor of 0.8 . The plant has an off in operation for 8 hours in the day. The plant use factor is *
A system has connected load of 120 kW, peak load of 100 kW, base load of 25 kW and average load of 48 kW. The load factor of the consumer is ?
An industrial plant has an aggregate load of 99 kW. The demand factor is 54 %. If the average total energy consumption of the plant in one year is 185 MWh, what is the yearly load factor of the plant? (Note: Aggregate is synonymous to Connected Load).
q20/ Complete the blank The load of 660 kVA with 0.62 power factor lagging, then the kW rating of the load is .....................................
Compute the average power dissipated by the load seen by the voltage source in the given figure. Let ω = 377 rad/s, Vs = 50 ∠0° V, R = 19.5 ohm, L = 0.08 H, and C = 200 μF.
A load consists of a 60-ohm resistor in parallel with a 90uF capacitor. If the load is connected to a voltage source Vs(t)=160cos(2000t) V, find the average power delivered to the load.
Problem : In the case of an industrial load with a power factor of 0.707 lagging, consuming 100 kW, and the line voltage at 60 Hz is 480Vrms, with a line resistance of 0.1Ω between the power company's transformer and the load, calculate the amount of power saved if the load's power factor changes to 0.94 leading. The answer is "3.771 Kilo-Watt has been saved" and also I want to know the concept of 'Power Factor'.
Write the types of power factor improvement.
Mention with explanation the techniques used to improve the power factor and what happen if the power factor is small
A voltage source V(t) = 10sqr(2)cos(377t + 90) is connected to a load, which is the parallel combination of an R = 5 ohm and XL = 10 ohm. What are the P and Q consumed in the load?