Answered: a heater is connected to voltage source…

a heater is connected to voltage source of 250 V and absorbs P= 1000 W. S= 1400 VA .What is the Power factor for this heater. What is the Impedance of the heater

Power System Analysis and Design (MindTap Course List)

6th Edition

ISBN:9781305632134

Author:J. Duncan Glover, Thomas Overbye, Mulukutla S. Sarma

Publisher:J. Duncan Glover, Thomas Overbye, Mulukutla S. Sarma

Chapter2: Fundamentals

Section: Chapter Questions

Problem 2.22P: The real power delivered by a source to two impedances, Z1=4+j5 and Z2=10 connected in parallel, is...

See similar textbooks

Related questions

Q: Solve for the following requirements Load Voltages Line Currents Source Complex Power

A: Since you have posted a question with multiple sub-parts, we will solve the first three subparts for…

Q: 1) A. a heater is connected to voltage source of 250 V and absorbs P= 1000 W. S= 1400 VA.What is the…

A: (a) The relation between active power (P), apparent power (S) and power factor (pf) is: Since, the…

Q: (a) What is the resistance of a 220-V AC short circuit that generates a peak power of 96.8 kW? (b)…

Q: heater has 3 equal induction-free elements, each with a resistance of 10 ohms. The elements is delta…

A: Since you have asked multiple questions in a single request, we will be answering only the first…

Q: A substation rated 1250 kVA is operating at full-load at 0.8 pf lagging and to carry an addition…

A: A substation is a place included in the electrical power generation system where electrical voltage…

Q: A 2300/230 V distribution transformer is delivering a load of 50 kW to a certain part of a…

A: According to the question we have to calculate the power actually delivered.

Q: Explain the working principle of three-phase separator. Support your answer with a diagram?

Q: Three equal star-connected inductors take 8 W at a power factor of 0.8 lagging when connected across…

A: According to the bartleby's guidelines we have to solve only first three subparts of a question so…

Q: An industrial load with a power factor of 0.707 lagging. If the voltage across the load is 98<0.…

Q: A 15 KVA closet transformer lovated inside a building is used to step down the voltage for the…

Q: 2)With reference to the waveform given below formulate the equation for the average value of DC…

A: Given A three phase supply is connected to bridge rectifier V=180 V R=200 ohm

Q: Three coils each having resistance 6  and inductance are connected in star with 415V. If the line…

A: Given Data: R = 6 ohm VL = 415 V IL = 30 A

Q: A SUBSTATION RATED 1250 KVA IS OPERATING AT FULL LOAD AT 0.8 PF LAGGING AND TO CARRY AN ADDITIONAL…

A: The substation is an electrical substation is a subsidiary station of energy technology,…

Q: 1) A. a heater is connected to voltage source of 250 V and absorbs P= 1000 W.S= 1400 VA .What is the…

A: The heater is connected to a voltage source of 250 Volts. The real power absorbed by the heater is…

Q: a) find the impedance Z b) current I delivered by the voltage source c) voltage VR d) average power…

A: In this question, We need to determine the impedance Z, current I, voltage VR and average power…

Q: 20- The data of the devices used in a 220 V sinusoidal single-phase workshop are given below.…

A: In the question A single phase system given. The supplied voltage = 220 V According to this; What…

Q: three phase converter has a rating of 500 kW when operating at unity power factor. Neglecting any…

A: We need to find out the rating of given system .

Q: A 15 kVa closet transformer located inside a building is used to step down the voltage for the…

Q: Two coils are connected in series. With 2 A d.c. through the circuit, the p.ds. across the coils are…

A: From the basics of a coil

Q: What is low power factor wattmeter and what is its use?

A: The instrument which measures the very low factor is known as the low power factor wattmeter (LPFW).…

Q: 2)With reference to the waveform given below formulate the equation for the average value of DC…

A: Given A three phase supply is connected to bridge rectifier V=180 V R=200 ohm

Q: hort term and long term effects of wind energy on power system

A: SHORT TERM AND LONG TERM EFFECTS OF WIND ENERGY ON POWER SYSTEM: 1. The following factors are…

Q: Three phase motor is rated 750 HP at 460-V line to line, with PF of 0.85 lagging and efficiency of…

A: The solution is given below

Q: (a) Considering pure resistance in an ac circuit element, show that the alternating voltage and…

Q: three phase converter has a rating of 600 kW when operating at unity power factor. Neglecting any…

A: We need to find out rating for the given power factor .

Q: A substation rated 1250 kVA is operating at full-load at 0.8 pf lagging and to carry an additional…

A: Methods to improve power factor Shunt Capacitor Phase modifier Synchronous condenser ( Floating…

Q: why need to improve a power factor (in electrical)

A: Given : In the above question they want to know the how the power factor can be improved in an…

Q: 352 452 I0V 15VT

Q: A substation rated 1250 kVA is operating at full-load at 0.8 pf lagging and to carry an additional…

A: Inductive element consume reactive power but Capacitive elements deliver reactive power into the…

Q: a.) How the improvement of the power factor decreases the line losses in the AC distribution…

A: Since it is not mentioned which question has to be solved and we are authorized to do one question…

Q: o the discussion about Power measurement using Wattmeter, Ammeter and Voltmeter & Power…

A: Note: We are authorized to answer three subparts at a time since you have not mentioned which part…

Q: A 100 KVA transformer has an iron loss of 3 kW and a full load copper loss of 4 kW. So at what kVA…

Q: A 2300/230 V distribution transformer is delivering a load of 50kW to a certain part of a community.…

A: In the question, 2300/230 V distribution transformer is delivering a load of 50kW to a certain part…

Q: A resistor R and an impedance coil Z are connected in series. The combination is supplied by a…

A: We need to find out power factor, current, impedance for given circuit

Q: Q2. A station supplies a load of 1000 kVA at a lagging power factor of 0.65. A synchronous motor is…

A: The solution is given below

Q: Solve for the voltage across the appliance and the current through it by referring the appliance to…

Q: A resistor, in series with a 138-microfarad capacitor, is connected to a 60-cycle source. If the…

A: A resistor, in series with a 138-microfarad capacitor, Frequency=60Hz The voltage drop across the…

Q: Complex Power The circuit in Figure 4 shows a voltage source with an AC signal of Vo = 40 + j0 V (a)…

Q: kVA closet transformer located inside a building is used to step down the voltage for the building.…

Q: A resistor R and an impedance coil Z are connected in series. The combination is supplied by a…

Q: 10A. Calculate the power consumed of the load, load impedance and power factor of the load. c) What…

A: a. Given NP=1NS=240Rm=1 ΩXm=0.5 ΩRz=0.5 ΩXz=0.25 Ω

Q: In an apartment with three flats fed from a 400V 60 Hz three-phase network, a 250W device in…

A: Given circuit: Line voltage

Q: Three coils each having resistance 6  and inductance are connected in star with 415V. If the line…

A: The value of inductance can not be calculated as frequency is not given.

Q: 1- Effective value when connected in series with a pure resistor R with resistance r and inductance…

Q: . A power station has a connected load of 48 MW. The energy generated for the year is 61,500 MWh. If…

Q: Q4 (a) Define power factor and describe the characteristic of current and voltage in capacitive…

A: Q4(a) Power factor tells us that how much of the apparent power is utilised. Power factor angle…

Q: A 240-V rms 60-Hz supply serves a load that is 10 kW (resistive), 15 kVAR (capacitive), and 22 kVAR…

A: The power factor of a circuit can be obtained as cos∅=PP2+Q2…

Q: A substation rated 1250 kVA is operating at full-load at 0.8 pf lagging and to carry an additional…

A: Capacitor banks are used to increase the power factor by compensating the reactive power.…

Question

A. a heater is connected to voltage source of 250 V and absorbs P= 1000 W. S= 1400 VA .What is the Power factor for this heater. What is the Impedance of the heater?

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

This is a popular solution!

SEE SOLUTION Check out a sample Q&A here

Step 1

VIEW

Step 2

VIEW

Step 3

VIEW

Trending now

This is a popular solution!

Step by step

Solved in 3 steps with 3 images

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Alternating Current (AC) Series Motor and Universal Motor

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, electrical-engineering and related others by exploring similar questions and additional content below.

Similar questions

3. What is power factor?
20- The data of the devices used in a 220 V sinusoidal single-phase workshop are given below. According to this; What is the apparent power of the load drawn by the current I1 in VA?
Discuss the concept of power quality in a power system and the various issues, such as harmonics and voltage sags, that can affect it.
Assume that vg = 120 V rms. Finda. The secondary current.b. The installation efficiency Pload/Psource.c. The value of the load resistance which can absorbthe maximum power from the given source.
A resistor, in series with a 138-microfarad capacitor, is connected to a 60-cycle source.If the voltage drop across the capacitor is 115 volts and the power taken by the circuitis 922 watts, calculate (a) the circuit current, (b) the ohmic value of the resistor, (c) theline voltage, (d) the circuit power factor. draw the circuit diagram
Discuss the differences between the current coil and voltage coil of a wattmeter from a design point of view.What will be the consequences if the current coil and voltage coil of a wattmeter are interchanged by mistake?What are the possible errors in this measurement?Can you measure power in an ac circuit by using an ammeter and voltmeter? If No, why? If yes, how?What is to be done if the wattmeter reads in the negative direction?
Obtain the value of the load ?? for maximum power transfer and the maximum power received by the load ?L
An industrial assembly hall is continuously lightedby one hundred 40-W mercury vapor lamps suppliedby a 120-V and 60-Hz source with a power factor of0.65. Due to the low power factor, a 25 percent penaltyis applied at billing. If the average price of 1 kWh is$0.01 and the capacitor’s average price is $50 permillifarad, compute after how many days of operationthe penalty billing covers the price of the power factorcorrection capacitor. (To avoid penalty, the powerfactor must be greater than 0.85.)
Q4. The source current in the circuit shown is in Figure 3a) What impedance should be connected across terminals a,b for maximum average powertransfer?b) What is the average power transferred to the impedance in (a)?c) Assume that the load is restricted to pure resistance. What size resistor connected across a,bwill result in the maximum average power transferred?d) What is the average power transferred to the resistor in (c)?v
Three coils each having resistance 6  and inductance are connected in star with 415V. If the line current is 30 A: a) find the value of inductive reactance as well as inductance value? B) If θ = 45 then calculate the power dissipation in kW when it is connected in Delta.
62. A power plant costumer draws power at 220 volts from transformers on a pole. Current transformers with ratio of 200/5 are used to meter the electrical usage. What is the multiplier of the kW-hr and demand meters? a. 50 b. 45 c. 40 d. 55
q1: Discussion of power quality aspects that need to be considered before installing the power factor correction unit