In the figure below, a joint is made by gluing two plywood gussets of thickness t to wood boards. The tensile working stresses are 1245psi for the plywood and 725psi for the boards. The working shear stress for the glue is 52psi. 1.95 in P 6.25in Determine the dimension b so that the joint is as strong as the boards. inches in 2 decimal places

In the figure below, a joint is made by gluing two plywood gussets of thickness t to wood boards. The tensile working stresses are 1245psi for the plywood and 725psi for the boards. The working shear stress for the glue is 52psi. 1.95 in P 6.25in Determine the dimension b so that the joint is as strong as the boards. inches in 2 decimal places

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

answer asap divide the figure, know the x and y each figure. plz illustrate the x and y of each figure, know the centroid
HELP WITH COMPLETE SOLUTION AND 4 DECIMAL PLACES, PLEASE DO NOT MAKE IT COMPLICATED THANK YOU Line AB was determined to be 2395.25m when measured with a 30m‐steel tape supported throughout its length under a pull of 4kg and at a mean temperature of 35°C. The cross‐sectional area of the tape is 0.03 cm^2, coefficient of thermal expansion is 0.0000116/°C and modulus of elasticity of steel is 2.0x10^6 kg/cm^2. Determine a. Correction for the measured length due to temperature if the tape usedis of standard length at a temperature of 20°C. Is the tape too long or tooshort? b. Correction for the measured length due to tension if the tape used isof standard length at a pull of 5 kg. Is the tape too long or too short? c. Correction for the measured length due to sag if it weighs 0.04kg/m d. the corrected length of line AB considering corrections from (a), (b) and (c)
A beam is subjected to uniform force w as shown in the figure below, E of the entire section is 30000 kips/inch^2, I is 240 in^4, if point A is supported by 0.003 rad clockwise before assembly, and point B is supported at Subside 0.3 inches before assembly, try to calculate the reaction force of point A and point B.
A wooden beam is loaded by a distributed load ww = 6 N/mm as shown in Figure Q4(a). The cross-section of the beam is shown in Figure Q4(b). Assume that LAB = 3000 mm, LBC = 2000 mm, W=190 mm, B0 = 10 mm, and H = 220 mm, h0=40 mm. Units: use N, mm, MPa as consistent units for all calculations. Decimal points: any decimal points are fine a) What is the maximum magnitude of shear force and bending moment, neglecting the sign? Maximum magnitude of shear force, positive value: Maximum magnitude of bending moment, positive value: b) Determine the maximum bending stress and shear stress that occurs in the beam. Maximum bending stress: Maximum shear stress
Steel design, i need a complete solutions thank u.. For built up shape shown in figure a) determine the elastic section modulus and b) plastic section modulus and the plastic moment mp, Bending is about x-axis and the steel is A36, FY=248 Given: 25.4 12.7 305 203
The bar shown determines: a) The internal force in section AB, BC and CD. b) The approach or distance between points B and C, and between points C and D. c) The displacement of points A, B, C and D. d) Conceptually, what is the difference between deformation and displacement? Consider: Cross-sectional area of the bar A=50 mm2 , Modulus of elasticity E = 200 x109Pa
strength of materials... answer only For the beam shown, calculate the magnitude of the bending stress (in psi) at the bottom of the beam on a section 1.52 feet to the right of B if P = 2002 lb, Q = 8084 lb, w = 1.18 in, L = 8.47 in, b = 3.69 in, and h = 1.12 in. Round off the final answer to two decimal places.
The frame shown in the figure is supported by a hinge at E and roller at D. Compute the horizontal and vertical component of the hinge force at C. as it acts upon BD *use 3 decimal place in rounding off all throughout the solution.
In the figure below, a joint is made by gluing two plywood gussets of thickness t to wood boards. The tensile working stresses are 1245psi for the plywood and 725psi for the boards. The working shear stress for the glue is 52psi. Determine the dimension b so that the joint is as strong as the boards.____________inches in 2 decimal places.
(I will vote it up for your effort thank you.)A rectangular bar is subjected to tensile forces of 2230 kN. Use E = 110 GPa and ν = 0.34. Determine the change in the dimension of its cross-section along X and Z directions. Also, calculate the change in the volume of the bar.
A rectangular bar is subjected to tensile forces of 2230 kN. Use E = 110 GPa and ν = 0.34. Determine the change in the dimension of its cross-section along X and Z directions. Also, calculate the change in the volume of the bar. i need a complete solution please, thank you
15. Compute the resultant of the three forces shown in the figure. A. 894.32 N B. 836.90 N C. None of the Above D. 315.28 N E. 948.27 N