In the figure below, calculate the rateat which the speed is changing (at), ifthe g= 8.8 m/s2 and a1= 9.1 m/s2.30°ajO 12.11 m/s29.1 m/s28.8 m/s217.9 m/s2bo

we will split the acceleration along two components , and then calculate the resultant to solve the…

Answered: In the figure below, calculate the rate…

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

Water flowing in a pipe reaches a point where the cross-sectional area of the pipe is reduced to 1/3 of its previous value. If the speed of the water before the constriction is 1.31 m/s, what is the speed of the water after the constriction?
A water station must discharge 450 m3 / h to supply a city. Determine the plumbing so that the average speed is 1.25 m / s.
While filling up your car with gasoline, you notice that it takes 3 minutes to dispense 55 liters of gasoline through the 2.5 cm diameter hose. What is the average speed, in m/s, of the gasoline inside the hose?
Water travels through a circular pipe with a diameter of 400 mm and at a speed of 5 m/s. The inertial force created by the flow is: Question 2Answer a. 100000 kgs/m b. 10000 kgs/m c. 1000 kgs/m d. 1000000 kgs/m
Answer is: V = 14.17 ft/s
Please give me the solution for the given answer: Ans. 7.88 m/s
Express Newton’s first, second, and third laws.
Pls answer asap I will give good ratings A jet of water flows from left to right and hits a splitter block, as shown in the figure. Some of the jet is diverted upwards and some of it downwards. The incoming jet has a velocity U1=U1=1.6 m/s and a cross-sectional area A1A1. The jet that is deflected upwards has a velocity U2=U2= 0.7 m/s, a cross-sectional area A2=A2= 11 cm22 and is at an angle θ2=θ2= 35oo with respect to the horizontal. The jet that is deflected downwards has a velocity U3=U3= 0.9 m/s, a cross-sectional area A3=A3=14 cm22 and is at an angle θ3=θ3= 25oo with respect to the horizontal. The density of water is ρ=ρ=1000 kg/m33.see diagram attached and answer - A-Find the cross-sectional area of the incoming jet (in cm22) B- Find the horizontal force on the block (in Newtons) (Note: remember to convert the area of the jets from cm22 to m22!) c)The vertical force on the block is found to be FyFy. What velocity of the incoming jet (i.e. what value of u1u1) would be needed to…
A boat moved by jet propulsion discharges water through a jet of area 0.02 m2; the water being drawn from inlet opening facing the direction of motion. The total drag is estimated to be 17.66 u2 N·m where u is the speed of the boat in metre per second. Take density of water at 1,020 kg/m3 and efficiency of the pump set is 78%. If the boat moves at 54 kilometers per hour, determine the following: A) Relative velocity of the jet in meters per second B) The power, in kilowatts, of the motor required to work the pumps C) Efficiency of propulsion, in %
A block of mass m slides along a horizontal surface lubricated with a thick oil which providesa drag force proportional to the square root of velocity.F_d=-bv^1/2If v = v0 at t = 0, determine v as a function of time
Consider two identical fans,one at sea level and the other on top of a high mountain, running at identical speeds. How would you compare ; (i) The volume flow rate . (ii)The flow rates of these two fans.
Determine the mean velocity, if the maximum velocity after comparing velocity relation is 5.5 m/s. _____ m/s

SEE MORE QUESTIONS

Recommended textbooks for you

Elements Of Electromagnetics

Mechanical Engineering

ISBN:

9780190698614

Author:

Sadiku, Matthew N. O.

Publisher:

Oxford University Press

Mechanics of Materials (10th Edition)

Mechanical Engineering

ISBN:

9780134319650

Author:

Russell C. Hibbeler

Publisher:

PEARSON

Thermodynamics: An Engineering Approach

Mechanical Engineering

ISBN:

9781259822674

Author:

Yunus A. Cengel Dr., Michael A. Boles

Publisher:

McGraw-Hill Education

Elements Of Electromagnetics

Mechanical Engineering

ISBN:

9780190698614

Author:

Sadiku, Matthew N. O.

Publisher:

Oxford University Press

Mechanics of Materials (10th Edition)

Mechanical Engineering

ISBN:

9780134319650

Author:

Russell C. Hibbeler

Publisher:

PEARSON

Thermodynamics: An Engineering Approach

Mechanical Engineering

ISBN:

9781259822674

Author:

Yunus A. Cengel Dr., Michael A. Boles

Publisher:

McGraw-Hill Education

Control Systems Engineering

Mechanical Engineering

ISBN:

9781118170519

Author:

Norman S. Nise

Publisher:

WILEY

Mechanics of Materials (MindTap Course List)

Mechanical Engineering

ISBN:

9781337093347

Author:

Barry J. Goodno, James M. Gere

Publisher:

Cengage Learning

Engineering Mechanics: Statics

Mechanical Engineering

ISBN:

9781118807330

Author:

James L. Meriam, L. G. Kraige, J. N. Bolton

Publisher:

WILEY

SEE MORE TEXTBOOKS

In the figure below, calculate the rate at which the speed is changing (at), if the g= 8.8 m/s2 and a1= 9.1 m/s2.