In the figure, C= 0.4 µF, E = 20 V, R1 = 10 k2, and R2 = 15 k2. Initially, the switch S is closed a long time so that the steady state is reached. Then S is opened at time t 0. Find: (a) the potential difference across the capacitor in the steady state situation. (b) the potential difference across R2 at t 4 ms after S is opened. (c) the current in R2 at t 4 ms after S is opened. %3D %3D S. Ra 3. R

In the figure, C= 0.4 µF, E = 20 V, R1 = 10 k2, and R2 = 15 k2. Initially, the switch S is closed a long time so that the steady state is reached. Then S is opened at time t 0. Find: (a) the potential difference across the capacitor in the steady state situation. (b) the potential difference across R2 at t 4 ms after S is opened. (c) the current in R2 at t 4 ms after S is opened. %3D %3D S. Ra 3. R

Introductory Circuit Analysis (13th Edition)

13th Edition

ISBN:9780133923605

Author:Robert L. Boylestad

Publisher:Robert L. Boylestad

Chapter1: Introduction

Section: Chapter Questions

Problem 1P: Visit your local library (at school or home) and describe the extent to which it provides literature...

See similar textbooks

Similar questions

In the circuit shown below, the switch has been open a long time and the circuit is initially in steady-state. At t=0, the switch is closed. R1=0.2Ω, and R2=0.4Ω. The batteries have EMFs E1=1V and E2=3V. The capacitor has capacitance 10 μF. Hint: What is the voltage on the capacitor just before the switch is closed? Note that there is a voltage drop over the open switch. a) What is the voltage over the capacitor before the switch is closed? b) Draw the Thevenin equivalent circuit as seen by the capacitor. c) What is the time constant for charging the capacitor? d) What is the voltage on the capacitor as a function of time?
An inductance of 1 H, a resistance of 8 Ω and capacitance of 0.04 F are connected in series with a variable voltage E = 50 sin 3t. Find the current and charge in the system, given the initial conditions q = 0 and l = 0 when t = 0, using method of solution of higher order linear ordinary differential equation.
For t >0 in the given figure, determine the time t at which i = 2.0 A, assuming DC steady state for t < 0. The time t when the current assumes the steady-state value is _______ ms.
a) Determine the differentila equation relating e0 and ii(t) b) time constant c) free response d) sketch the response to reach a steady state if ii(t) = 2A while capacitor has V0 =0
The switch in the circuit has been open for a long time before closingat t = 0 s a) Draw the RC circuit for t < 0 and calculate the capacitor voltage just beforethe switching, Vc(0−). b) Draw the circuit after switch has closed (for t > 0), and obtain the Theveninequivalent as seen by the 5 nF capacitor. c) What is the voltage across the capacitor when t → ∞? d) Find the numerical expression for Vc(t) for t ≥ 0 s. e) Find the numerical expression for ic(t) for t ≥ 0 s. f)Find the numerical expression for the power delivered by the voltage controlled current source for t ≥ 0 s.
Consider the circuit given below, where V = 120 V, R = 2.4 kΩ, and L = 60 mH. What is the time constant of the circuit with S1 closed? What is the time constant of the circuit with S1 closed? What is the eventual steady-state current with S1 closed? What is the value of the circuit current at the first instant (t = 0 s) S1 is closed? What is the value of the circuit current exactly one time constant after S1 is closed? How long after S1 is closed will it take before the circuit current reaches its steady-state value?
Can you please help with this question? The triangular voltage pulse shown below is applied to a 200 mF capacitor. a) Write the expressions thatdescribe vc(t) in the five time intervals t < 0, 0 ≤ t ≤ 2 , 2 ≤ t ≤ 6, 6 ≤ t ≤ 8, and t > 8. b) Derive theexpressions for the capacitor current, power, and energy for the time intervals in part (a).
The triangular voltage pulse shown below is applied to a 200 mF capacitor. a) Write the expressions thatdescribe vc(t) in the five time intervals t < 0, 0 ≤ t ≤ 2 , 2 ≤ t ≤ 6, 6 ≤ t ≤ 8, and t > 8. b) Derive theexpressions for the capacitor current, power, and energy for the time intervals in part (a).
The circuit shown below is an underdamped system, and the current through the inductor has the form iL(t)=e^at ( ) (K1sinwt + K2coswt ) for t≥0 a. Determine the numerical values, including signs, of a and w b. If the initial conditions are iL(0) = 1A and Vc (0) =12V , determine the numerical values, including signs, of K1 and K2 c. Using the numbers determined above, write out the complete expression for iL(t)
IN THE CIRCUIT SHOWN, CONSIDER THAT V1=20 VDC, R1=1000 Ω, R2=3000 Ω, R3=3500 Ω AND C=1 mF.DETERMINE:A) THE TIME IT TAKES FOR THE CAPACITOR TO REACH ITS FINAL VALUE (5T), WHEN SWITCH 2 (INT 2) IS IN POSITION A AND SWITCH 1 (INT 1) IS CLOSED AT t=0,B) THE ENERGY STORED BY THE CAPACITOR ONCE IT HAS BEEN FULLY CHARGED WITH THE SAME POSITION OF SWITCHES AS ITEM A)C) ONCE THE CAPACITOR HAS BEEN FULLY CHARGED WITH SWITCH 1 CLOSED, SWITCH 2 MOVES POSITION (GOES TO B) AT A NEW t=0. NOW DETERMINE THE VALUE OF THE VOLTAGE ON THE CAPACITOR AT t=3.5 SECONDS
In Figure, suppose the switch has been closed for a time interval sufficiently long (steady state) for the capacitor to become fully charged. R 1 = 9 kΩ, R 2 = 12 kΩ, R 3 = 2 kΩ, C = 14 × 10 −6 F, and an ideal battery has emf ε = 12 V. The switch is now opened at t = 0. Find the current in R 2 at time t = 0.09 s. (Your result must be in mA's and include 3 digit after the decimal point. Maximum of 5% of error is accepted in your answer.)
The voltage pulse applied to the 100 mH inductor shown is 0 for t<0 and is given by the expression v(t)=20te−10t V for t>0. Also assume i=0 for t≤0. Sketch the current as a function of time.