In the figure shown, the load needs to be raised 28 ft. Noting that Gear A is initially at rest and it has a constant acceleration until it reaches 120rpm velocity in 5s, it maintains a uniform velocity of 120 rpm after. Solve for (a) the total time the load was raised at the required height(in seconds). (b) the angle of change of Gear A (in revolution). 3 in. 18 in. 15 in. Load

In the figure shown, the load needs to be raised 28 ft. Noting that Gear A is initially at rest and it has a constant acceleration until it reaches 120rpm velocity in 5s, it maintains a uniform velocity of 120 rpm after. Solve for (a) the total time the load was raised at the required height(in seconds). (b) the angle of change of Gear A (in revolution). 3 in. 18 in. 15 in. Load

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

l=160mm, b=60mm. AB rotating with constant angular velocity 1600 rpm clockwise. determine the velocity of P. θ = 45°
Water enters a two-armed lawn sprinkler along the vertical axis at a rate of 150 L/s, and leaves the sprinkler nozzles as 2cm diameter jets at an angle of u from the tangential direction. The length of each sprinkler arm is 0.52 m. Disregarding any frictional effects, determine (a) Angular momentum and (b) the rate of rotation n of the sprinkler in rev/min For ϴ = 60°.
A block of mass m = 2.00 kg rests on the left edge of a block of larger mass M = 8.00 kg. Thecoefficient of kinetic friction between the two blocks is 0.300, and the surface on which the 8.00-kgblock rests is frictionless. A constant horizontal force of magnitude F = 10.0 N is applied to the2.00-kg block, setting it in motion as shown in Figure P5.65a. If the length L that the leading edgeof the smaller block travels on the larger block is 3.00 m, (a) how long will it take before this blockmakes it to the right side of the 8.00-kg block, as shown in Figure 3? (Note: Both blocks are set inmotion when F is applied.) (b) How far does the 8.00-kg block move in the process?
Immediately after the bouncing golf ball leaves the floor, its components of velocity are Vx = 0.761 m/s, and Vy = 3.159 m/s. Determine the horizontal distance (meters) from the point where the ball left the floor to the point where it hits the floor again.
The angular velocity of rod OB varies as tetha = 8 - 12t^2 rad/s where t is in seconds. Compute the magnitude of the acceleration of point B at (a) t = 0; and (b) t= 1.0s.
The position of the slider P in the rotating slotted arm OA is controlled by a power screw as shown. At the instant represented, θ˙ = 5.4 rad/s and θ¨ = -35 rad/s2. Also at this same instant, r = 396 mm, r˙ = -251 mm/s, and r¨ = 0. For this instant determine the r- and θ-components of the acceleration of P.
If a particle has initial velocity of v0 = 12 ft/s to the right, at s0 = 0, determine its position when t = 10 s, if a = 2 ft/s2 to the left.
The 1000N block shown started at rest and moves towards the right. Which if the following gives the distance that 1000N block will travel along the horizontal surface if the coefficient of friction between block and the surface is 0.20. Assume pulley to be frictionless.
A car moves in a straight line with a velocity of v = (3t2-7t) m/s, and t is in seconds. Determine its position in meters at t = 5s if when t=0, x=0.
Calculate the moment M2 and M3 Using three moment equation. Try to answer in short.
1-Moment of inertia of the pulley (kg.m2) ? 2-tension in rope of m1 (N) ? 3-tension in rope of m2 (N) ? 4-angular acceleration of the pulley (rad/s2) ? 5-acceleration of block m1(m/s2) ? 6-acceleration of block m2 (m/s2) ?
If the e = 45°, and the bar 0Q is rotating in the counterclockwise direction at 1.6 rad/s, which of the following is the velocity of the slider P?.