In the figure, the hanging object has a mass of m1 = 0.420 kg; the sliding block has a mass of m2 = 0.850 kg, and the pulley is a hollow cylinder with a mass M = 0.350 kg, a interior radius R1 = 0.0200 m and an exterior radius R2 = 0.0300 m. Assume that the mass of the rays is negligible. The coefficient of kinetic friction between the block and the surface horizontal is µk = 0.250. The pulley rotates without friction on its axis. The lightweight cable does not stretch and does not slip on pulley. The block has a velocity of vi = 0.820 m / s towards the pulley when you pass a landmark on the table. (a) Use energetic methods to predict its velocity after it has passed a second point, which is at 0.700 m. (b) Find the angular speed of the pulley at the same moment.

Q: Q4. As shown in the image below, a force of P= 310 N is applied to the 64-kg cart. The dimensions…

A: To find : To find the total normal reaction at the wheel A. Given :   force P=310 N…

Q: As shown in the figure, a rod of mass m= 1 (kg) and length L = 1 (m) is standing between the…

A:

Q: The wheel in the figure has a mass of 40 kg and a radius of rotation, in relation to its center of…

A: Work done = Fs cos(thita)  and in this question workdone by weight has to be find.

Q: The 10 kg slender bar AB, shown in the figure, has a length of 2 m. A block of negligible mass,…

A:

Q: This climber (mass=52kg) is maintaining this posture while grabbing onto a rock at P3 and reaching…

A:

Q: The arms of a Porter governor are 375 mm long. The upper arms are pivoted on the axis of rotation.…

A:

Q: A Hartnell govermor has two rotating balls, of mass 2.7 kg each. The ball radius is 125 mm in the…

A:

Q: A man pushes bar CD to either initiate uphill motion of the homogeneous spool or to just keep the…

A:

Q: This climber (mass=52kg) is maintaining this posture while grabbing onto a rock at P3 and reaching…

A:

Q: 1. Two blocks, of masses M = 2.3 kg and 2M are connected to a spring of spring constant k = 180 N/m…

A:

Q: The motorcycle in the figure has a mass of m1 kg and its center of mass is at G1. The mass of the…

A:

Q: The 2 kg ring is at the rest at point A as shown in the figure. If it is released through the…

A: Given data as per the question Mass =2 kg Spring  stiffness =21 KN/m

Q: Problem 3 A 730-lb motorcycle and rider have a combined center of mass at a distance b = 33 in.…

A:

Q: 1. Two blocks, of masses M = 2.3 kg and 2M are connected to a spring of spring constant k 180 N/m…

A: m = 2.3 kg k = 180 N/m u = .12

Q: Consider a solid cylinder of mass 5 kg and radius 0.3 m on a surface with insufficient friction so…

A:

Q: The cable of the 1600 kg elevator cab in the figure snaps when the cab is at rest at the first…

A:

Q: The 13-kg sphere C is released from rest when θ = 0∘ and the tension in the spring is F = 100 N.…

A: First calculate the length of the spring in rest position.

Q: a trolley of mass m stands on frictionless rails.a rod of mass m and length l is pivoted to the roof…

A: Write the free-body diagram of the system.

Q: The figure below are two discs D and E which have a mass of 200 lbs and 100 lbs, respectively. If P…

A:

Q: Block A has a weight of 60 lb and block B has a weight of 10 lb. Neglect friction and the mass of…

A:

Q: A garage door is mounted on an overhead rail. The wheels at A and B have rusted so that they do not…

A: We have to determine The above question Find the maximum value hh can have without causing one wheel…

Q: 3)The masses of the A and B blocks are mA and mB, respectively. These two blocks are connected by a…

A: first of all we make FBD of both the block , assuming force on the arm is T, and mass A and B moves…

Q: 1. Two blocks, of masses M = 2.3 kg and 2M are connected to a spring of spring constant k = 180 N/m…

A:

Q: In reference to the figure below, if uk = 0.7 at the rear drive wheels B of the 1550 lb race car…

A:

Q: The mine car and its contents as shown in Figure Q1 have a total mass of 6 Mg and a center of…

A: Given Data The force acting on the cart is: F=10 kN The height of the cart is: h=0.9 m The distance…

Q: The motorcycle in the figure has a mass of m1 kg and its center of mass is at G1. The mass of the…

A: Given data  a = 0.41 m b = 0.39 m c = 0.75 m d = 0.25 m e = 0.58 m m 1= 120 kg m2 = 77 kg fs = 0.82

Q: Review I C Blocks of mass m, and ma are connected by a massless string that passes over the pulley…

A:

Q: A 4.6-kg block is pushed 2.3 m up a vertical wall with constant speed by a constant force of…

A:

Q: The lawn mover

A: Given, μA=0.18μB=0.12 Total mass, M=50 kg

Q: The drum, with radius R = 1.9 m, is given an initial counterclockwise angular velocity ω0. The drum…

A: The force that is applied at an eccentric distance to the desired point is termed as eccentric…

Q: A stationary bicycle wheel of radius 0.7 m is mounted in the vertical plane (see figure below). The…

A:

Q: 7-37 The 20-kg ladder AC is leaning on a 5-kg block at B and a frictionless corner at C. Both bodies…

A: 7.37 First, draw the free-body diagram of the ladder: Here N is the reaction force applied by block…

Q: The crate, which has a mass of 125 kg, is subjected to the action of the three forces shown in the…

A: Given: Mass of the crate (m)=125kg P1=500N P2=700N P3=800N Θ=45° µk=0.40

Q: 6/15 The 1650-kg car has its mass center at G. Calculate the normal forces NA and NB between the…

A: Explanation: The stepwise procedure to solve this problem is shown in the following attached image:

Q: In the given figure below, a 3.0 -kg block is sliding down a 60°-rough incline. The speed of the…

A: we know the initial energy of the system =K.E of a block + gravitational P.E of…

Q: A ball is shot at high speed into a frictionless channel that is in the shape of a segment of a…

A: there are 3 forces acting on the ball.

Q: An inclined plane of angle e = 20.0° has a spring of force constant k = 510 N/m fastened securely at…

A:

Q: The 114-kg crate of the figure below is being moved by a rope that passes over a smooth pulley. The…

A: Disclaimer: “Since you have posted a question with multiple sub-parts, we will solve the first three…

Q: A hollow, smooth cylindrical spool has inner radius R/ 2, outer radius R and mass M. The roller is…

A:

Q: A cylinder of mass M=500kg has an axle of radius b=1m and a spool of radius R=3m. It is placed…

A:

Q: All arms of porter governor are 18 cm long and hanged at a distance of 4 cm to axis of rotation. The…

A: Porter governor is a modified form of watt governor of which the sleeve is loaded with heavy mass.…

Q: A "swing ride" is shown in the figure. For b=1.6 m, L=4.2 m and 0=36° neglect the mass of the cables…

A: Given:-b=1.6mL=4.2mθ=36°m=37kgTo find:-1) Radiys of horizontal circle2) Tension in cable3) Velocity…

Q: 7: Two masses of 14 kg and 7 kg connected by a fexible inextensible cord rest on inclined plane…

A: Tension force always tries to pull the body it never pushes the body that's why it acts away from…

Q: A block of mass m2=6kg resting on a rough horizontal plane is pulled by an inextensible string…

A: Answer: (a) The acceleration of mass m1 is 0.88 m/s2 (downward) and the acceleration of the mass m2…

Q: |A body of weight 600N, is placed on a 20° inclined plane and pulled by a 500N force, applied…

A:

Q: The wheel in the figure has a mass of 40 kg and a radius of rotation, in relation to its center of…

A: Please find the required solution in the steps ahead, please UPVOTE, I really need it, and i will…

Q: The first mass that will reach the bottom of the ramp will be:

A:

Forming and Shaping

Metal forming is a category of metalworking process through which the material can be given the desired shape and size by subjecting it to plastic deformation, where the component undergoes bulk deformation process upon application of loads. Unlike the shearing and machining process, the material does not undergo up to a failure point as indicated in the stress-strain curve. Hence, the stresses induced during the forming process are greater than yield strength but less than the failure strength of the material. The process does not lead to the loss of material, so it can be said to be an economical process. During forming, the material is subjected to tensile forces, compressive forces, bending, and shearing loading conditions. The material should possess the property of ductility to undergo the forming process.