In the Fink truss shown in Figure, the web members BC and EF are perpendicular to the inclined members at their midpoints. Use the method of sections to determine the force in member DE if: P=86 Kn Q=45 Kn Use 2 Decimal places. If the member is in compression you need to include the negative (-) sign in your inputted answer. Do not include the unit in inputting your answer. P Q Q 3 m 4 m 4 m 4 m

In the Fink truss shown in Figure, the web members BC and EF are perpendicular to the inclined members at their midpoints. Use the method of sections to determine the force in member DE if: P=86 Kn Q=45 Kn Use 2 Decimal places. If the member is in compression you need to include the negative (-) sign in your inputted answer. Do not include the unit in inputting your answer. P Q Q 3 m 4 m 4 m 4 m

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

Solve for the member forces of the truss. AB has a length of 2m while AD and DE is 1.5m. INDICATE IF MEMBER FORCES ARE IN COMPRESSION ANSWER UP TO 5 DECIMAL PLACES -AB -AD -BC -CD -DE -CE
A tripod shown supports a load of P = 1000 N at point A. Take note that ball and socket joints are used to mount the triopd at points B, D, and C. Consider the following:L1 = 2L2 = 4L3 = 5θ = 45°α = 30 Point C coordinates: (2, -2, 3) *Do not use Vectors in solving Determine the following: Force of AB = __NForce of AC = __NForce of AD = __N
FORCE METHOD An overhang beam ABC is loaded as shown. Determine the reactions at the supports due to loading and a support settlement of 1 mm at the roller B. Take E = 200 GPa and I = 500(10^6) mm^4.
Given the problem: 1.) In the frame, shown, members 'ACE' and 'BCD' are connected by a pin at 'C' and by the link 'DE'. For the loading shown, determine this: d.) Vertical component at ‘C’ on member ‘BCD’ in N.e.) Total force exerted at ‘C’ on member ‘BCD’ in N. *Round off final answer in 4 decimal places. Thank you.
The timber member BC, inclined at angle Θ=60 degrees to the vertical, is supported by a pin at B and the 0.75in. diameter steel bar AC.(a) Determine the cross-sectional area of BC for which the displacement of C will be vertical when 5000lb force is applied.(b) Compute the corresponding displacement of C.The moduli of elasticity are 1.8 x 106 psi for timber and 29 x 106 psi for steel. Neglect the weight of BC.
The timber member BC, inclined at angle 0 = 60° to the vertical, is supported by a pin at B and the 0.75-in.-diameter steel bar AC. (a) Determine the cross-sectional area of BC for which the displacement of C will be vertical when the 5000-1b force is applied. (b) Compute the corresponding displacement of C. The moduli of elasticity are 1.8 x 106 psi for timber and 29 x 106 psi for steel. Neglect the weight of BC.
Determine the force in member BA (in lb, round-off to 2 decimal places, include "-" if compression) of the scissors truss shown. P = 150.0 lb, Q = 75.0 lb, and L = 10.0 ft.
Assuming that P = 48 000 lb and that it may be applied at any joint onthe line FJ, determine the location of P that would cause (a) maximum tension inmember HI; (b) maximum compression in member CI; and (c) maximum tensionin member CI. Also determine the magnitude of the indicated force in each case
A horizontal beam is supported by an inclined strut and carries a load of 15 kN at joint AD CBD in the figure. The strut, which consists of two bars each of thickness 40 mm, is connected tothe beam by a rivet passing through the three bars meeting at joint. The allowable shear Cstress and bearing stress are all, z =60 MPa and =120 MPa, respectively.a) Determine the required diameter of the rivet at the hinge that carries safely by the given Csystem.b) If the diameter rivet used on the support is 20 mm check whether this rivet diameter is Asufficient for the given system.
Answer is -66.35. No other answer thanks. A roof truss is shown in the figure and loaded as such. If force P = 93.84 kN, find the force in member BC (in kN). Neglect H1, H2, and H3. Use a = 4 m., and b = 6 m.
Q1-For the truss shown in figure, assume any value for the length (b) and explain how to find the forces in each member
The timber member BC, inclined at angle ϴ=600 to the vertical, is supported by a pin at B and 0.75in. diameter steel bar AC. (a) Determine the cross-sectional area of BC for which the displacement of C will be vertical when 5000lb force is applied. (b) Compute the corresponding displacement of C. The moduli of elasticity are 1.8 x 106 psi for timber and 29 x 106 psi for steel. Neglect the weight of BC.