In the manometer shown, if h, is 65 cm, considering that the value of h1 is a 1/4 of h2 while the value of h3 is thrice of h1, what will be the value of PA - Pg in kPa? (The gray fluid at points Ahas density of 142 mg/L, the green fluid at point B has density of 336 g/m°, while the yellow fluid has density of 400 g/m3. Use g = 9.81m/s-). Show your answers in 2 decimal places.Y3h3Y1h2A+ In the open u-tube manometer shown, if h1 is 58 cm, considering that the value of h2 is four times of h1, what will be the value of PA in kPa? (The green fluid at points A has density of 166 kg/m while%3Dthe blue fluid has density of 333 mg/mL. Use g = 9.81m/s-). Show your answers in 2 decimal places.h2h,(3)U- Tube Manometer

We are authorized to answer one question at a time, since you have not mentioned which question you…

In the manometer shown, if hy is 65 cm, considering that the value of hy is a 1/4 of h2 while the value of h3 is thrice of h1, what will be the value of PA - PB in kPa? (The gray fluid at points A has density of 142 mg/L, the green fluid at point B has density of 336 g/m3, while the yellow fluid has density of 400 g/m3. Use g= 9.81m/s2). Show your answers in 2 decimal places. 73 ha Y1 h: A+ 72

In the manometer shown, if hy is 65 cm, considering that the value of hy is a 1/4 of h2 while the value of h3 is thrice of h1, what will be the value of PA - PB in kPa? (The gray fluid at points A has density of 142 mg/L, the green fluid at point B has density of 336 g/m3, while the yellow fluid has density of 400 g/m3. Use g= 9.81m/s2). Show your answers in 2 decimal places. 73 ha Y1 h: A+ 72

Engineering Fundamentals: An Introduction to Engineering (MindTap Course List)

5th Edition

ISBN:9781305084766

Author:Saeed Moaveni

Publisher:Saeed Moaveni

Chapter10: Force And Force-related Variables In Engineering

Section: Chapter Questions

Problem 26P: SAE 30 oil is contained in a cylinder with inside diameter of 1 in. and length of 1 ft. What is the...

See similar textbooks

Similar questions

For the manometer shown in the image, all fluids are at 20 degrees C. If PB-PA = 89.5 kPa, determine the height H in centimeters. The specific weight of water is 9790 N/m^3 and the specific weight of mercury is 133100 N/m^3
6. Freshwater and seawater flowing in parallel horizontal pipelines are connected to each other by a double U-tube manometer, as shown in figure. Determine the pressure difference Pfresh water- Psea water= ?(kPa) between the two pipelines. Take the density of seawater at that location to be P = 1035 kg/m³. (2 decimal)
A 10 cm diameter sharp edged orifice (C=0.60) is located at the vertical side of a tank having a horizontal cross section 2 m square. An inflow of 23 L/s keeps the head over the orifice constant. If the inflow is changed to 34L/s, how long will it take for the head over the orifice to reach 2.0 m? a.260 seconds b.235 seconds c.35 seconds d.415 seconds
As shown in the figure, water flows in the horizontal pipe. The pipe consists of two different sections, 60 mm and 30 mm in diameter, connected by a smooth reduction. The pressure difference between the two sections is measured with a mercury manometer. Friction effects are neglected. The height between the mercury levels in the two sections of the pipe was determined as 1.4m. Find the velocity and mass flow at points 1 and 2. (Density of mercury: 13.6 grams / cm3, Density of water: 1gr / cm3)
FLUID MECHANICS-WATER HAMMER: A valve at the end of a gasoline pipeline is rapidly closed (assume instantaneously). If the gasoline velocity was initially 12m/s, what will be the water hammer pressure rise? The bulk modulus of the gasoline is 715 MPa, and the density of the gasoline is 680 kg/m3.
An open cylindrical tank 800mm in diameter and 2000mm high contains water to a depth of 1.6m. It is rotated about its vertical axis at 13 rad/s. How many liters of water are spilled? Use density of water as 1000kg/m3 and specific weight as 9.81kN/m3
In a manometer shown, the fluid from A to B is mercury (sp. gr. = 13.6) and fromB to C, the fluid is oil (sp. gr. = 0.80). At what height, h, of oil will give a pressureof 452 grams/cm2at C. Use density of water of 1.0 grams per cu.cm.
the reading of an automobile fuel gage is proportional to the gage pressure at the bottom of the tank. if the tank is 30 cm. deep, and is contaminated with 3.42 cm. of water at the bottom, how many meters of air remains at the top when the gage indicates "FULL"? use weight of: gasoline = 6.62 kN/m^3; air = 14.67 N/m^3. the tank is closed.
Consider a rectangular plate of width B = 1m (measured in the direction normal to the plane of this sheet) and negligible thickness, which separates two fluids of densities ρ and ρw. A mass of density ρs is supported by an inextensible rope that passes through a pulley connected to one end of the plate. Consider that ρ = 1.59ρw and ρs = 2.40ρw, where ρw = 1000 kg/m3. Determine the volume that this mass must have for the system to remain in equilibrium, as shown in the figure.
A pressure in a given tank reads 265 mm of Hg. Determine the equivalentheight of a certain fluid in m with sp. gr = 3.44.
Oil is filled within a tall cylindrical tank. A flat disk with a height of 1 cm and with a diameter of 5 cm is placed into the oil. There occurs a narrow spacing of 0.1 mm between the disk and the tank wall. Due to the forces acting on the disk, it moves downward, and after some time, the speed of the disk reaches a terminal velocity. Beyond this moment, measurements reveal that the disk moves 30 cm in 4 seconds. If the oil density is 600 kg/m3and the specific gravity of the disk is 1.5, determine the oil’s viscosity.
The water flow rate in the pipe will be measured using the pitot tube system given in the figure. At point 1, the velocity is zero and represents the stationary point. Since there is mercury with a density of 13600 kg/m3 in the manometer and the height of the manometer is read 0.06, calculate the volumetric flow rate of the water flowing in the pipe with a diameter of 0.2 m. (ρwater = 1000 kg/m3)