In the mechanism shown in figure below, the crank OA drives the sliders B and D in straight paths through connecting links AB and CD. The lengths of the links are OA = 150 mm, AB = 300 mm, AC= 100 mm and CD= 450 mm. OA rotates at 60 rpm clockwise and at the instant has angular retardation of 16 rad/S2. Determine: (a) the velocity and acceleration of the slider B and D (b) the angul velocity and acceleration of link CD D mmmh B

In the mechanism shown in figure below, the crank OA drives the sliders B and D in straight paths through connecting links AB and CD. The lengths of the links are OA = 150 mm, AB = 300 mm, AC= 100 mm and CD= 450 mm. OA rotates at 60 rpm clockwise and at the instant has angular retardation of 16 rad/S2. Determine: (a) the velocity and acceleration of the slider B and D (b) the angul velocity and acceleration of link CD D mmmh B

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

The device in the figure, B and C are pins, the center disk C rolls without sliding on the contact D, and the bar 4 slides inside the guide 5, whose pin A is mounted on the bar OB. Angular velocity ω1 and a known angular acceleration ?1 are known. At the instant shown, find: a) The angular velocity of the bar 4 b) The angular acceleration of bar BC Data: OA = ?, AB = 2?
In the mechanism shown in the figure, Ring A moves in a vertical direction with a downward speed of 2-m/S and an acceleration of 3-m/s^2. The radius of the pinion gear is 200-mm, and the radial distance of the B end of the 500-mm long AB rod to the pinion center is 150-mm. Find the angular velocity and angular acceleration of the pinion gear moving on the fixed rack gear at the moment shown in the figure.
Dynamics Lesson For the electric saw shown in the figure, the saw can slide left and right on the horizontal bed where it is placed. Since the engine rotates the crank counterclockwise with a constant angular velocity of 60 dv/min, find the acceleration of the saw and the angular acceleration of the arm AB for the position where ?=90o
The figure is made of rigid members AB, BC, DE, and EF, whichare pinned at A, B, D, E, and F. End C of member BC is pinned to a block which slides on member DE. For the given position, angular velocity of member AB = 2 rad per sec clockwise and angular acceleration of member AB = 3 rad / s^2 counterclockwise. Find the linear velocity and acceleration of the block at C for this position.
For the instant shown in the figure, the angular velocity and the angular acceleration, of the bar AB, is 3 rad / sec and 5 rad / sec2, respectively. Setting up the equations vectorially, determine: 1. The speed of B. 2. The acceleration of B. 3. The angular velocity of the bar BC. 4. The angular velocity of the bar CD. 5. The angular acceleration of bar BC. 6. The angular acceleration of the bar CD 7. The acceleration of C. Also, using the Instantaneous Center of Rotation (C.I), determine: 8. The angular velocity of bar BC. 9. The velocity of C (magnitude and direction)
A disk shown below rolls without slipping on the ground. At the instant shown, when peg A is directly above O, the disk is rolling counter clockwise, with angular velocity ω = 2 rad/s increasing at a rate α = 4 rad/s. A motor on the shaft through B commands link BC to rotate such that the disk rolls with constant angular acceleration until OA becomes horizontal. 1. What is the angular velocity and angular acceleration of link BC at the instant when the disk has rotated an angle θd from its configuration shown in the figure.
The bucket of a backhoe is the element AB of the four-bar linkage system ABCD. Assume that the points A and D are fixed and that the bucket rotates with a constant angular velocity WAB = 0.25 rad/s. In addition, suppose that, at the instant shown, point B is aligned vertically with point A, and C is aligned horizontally with B. Determine the acceleration of point C at the instant shown along with the angular acceleration of the elements BC and CD. Let h= 0.66 ft, e= 0-46 ft, l= 0.9 ft, and w= 1.0 ft.
(Three-Dimensional Motion) The figure below represents a pair of bevel gears A and B. Gear A rotates in ahorizontal plane about a vertical axis at O. Gear B rotates around the shaft OC which in turn rotates about the terminal axis at O. determine the angular accelera tion of gear B when gear A is stationary and member OC has an angular velocity of 10j rad/sec and and angular acceleration of 25j rad/sec2 .
In the figure, Pulley A, rotating at 20 rad/s, controls the motion of Pulley B. The motor of pulley A is cut off, and friction eventually brings the pulleys to a stop with an angular acceleration of α = -2.5t rad/s2. If there is no slippage, determine: a. The angular velocity of B with respect to time b. The angular displacement of B during the deceleration c. The acceleration of point C with respect to time
In the given figure, A link OB is rotating with a constant angular velocity of 2 rad/s in counter clockwise direction and there is a block is sliding radially outward on it with an uniform velocity of 0.75 m/s with respect to the rod, If OA = 1m , find the magnitude of the absolute acceleration of the block at location A ?
In the mechanism shown in the figure, the C pin attached to the element no. can slide. Calculate the angular velocity and angular acceleration of slide number 3. Elements 2 and 3 Calculate the accelerations of the centers of gravity. θ.2 rad/s=18 θ..2 rad/s 2 = 33 r2 = 900mm d2 = 530mm s3 = 430mm d4 = 330mm
The slider crank mechanism given in the figure has a crank AB of length 190 mm and the connecting rod BC is of length 800 mm. At the instant shown find: A) The velocity of the crank pin at B B) The velocity of the piston C) The velocity of the pint D which is at the centre of the connecting rod D) The angular velocity of the connecting rod