In the structure below, member AB is attached to the wall with a fixed support at A and is attached to member BC with a fixed support at B. Force F has a value of 42 lb. Force G has a value of 20 lb. What is the magnitude of the total reaction force that the ground provides at fixed support A in lb? 2ft 3ft B PA 300 A 1.5ft F 45°

In the structure below, member AB is attached to the wall with a fixed support at A and is attached to member BC with a fixed support at B. Force F has a value of 42 lb. Force G has a value of 20 lb. What is the magnitude of the total reaction force that the ground provides at fixed support A in lb? 2ft 3ft B PA 300 A 1.5ft F 45°

International Edition---engineering Mechanics: Statics, 4th Edition

4th Edition

ISBN:9781305501607

Author:Andrew Pytel And Jaan Kiusalaas

Publisher:Andrew Pytel And Jaan Kiusalaas

Chapter10: Virtual Work And Potential Energy

Section: Chapter Questions

Problem 10.62P: The bar ABC is supported by three identical, ideal springs. Note that the springs are always...

See similar textbooks

Similar questions

A smooth inclined plane has a gradient of 1 in 6. Calculate the mass of a body that can be held in equilibrium on the plane by a force of 80 N when the force acts: (a) parallel to the plane answer M=49.62kg (b) horizontally answer M=48.94 kg (c) at an angle of the 20° with the plane. answer M=46.62kg
P1=215 N P2=325 N P3=150 N L1=3m L2=4m 1. Draw a "free body diagram". The diagram should be for members BE, BF, CF, and DF to help solve. 2. What is the force on members CF, BF, BE? Is each of these members having tension or compression?
A 2.0m long bar is being used as a first-class lever. It has a load of 720 N placed on one end (located 1.2 m from the fulcrum) and the effort is being applied at the opposite end. A. State the law of the leaver B draw a diagram of the lever, showing the load,effort,fulcrum, effort arm, and load C determine the effort force needed to balance the load. D if this lever has an actual mechanical advantageous 1, determine the percent efficiency of the leaver.
To move a heavy crate across a floor, one end of a rope is tied to it and the other end is tied to a wall 30 ft away. When a force of 100 lb is applied to the midpoint of the rope, the rope stretches so that the midpoint moves to the side by 2 ft. What is the force on the crate? Select the correct response: 400 lb 500 lb 410 lb 379 lb
A man having a weight of 195 lb attempts to hold himself using one of the two methods shown in (Figure 1). Neglect the weight of the platform. a) Determine the total force the man must exert on bar AB in case a. Express your answer in pounds to three significant figures. b) Determine the normal reaction he exerts on the platform at C in case a. Express your answer in pounds to three significant figures. c) Determine the total force the man must exert on bar AB in case b. Express your answer in pounds to three significant figures. d) Determine the normal reaction he exerts on the platform at C in case b. Express your answer in pounds to three significant figures.
Physics for Engineering A uniform bar 3.00 m long is held by ropes at the ends making angle 60.0 and 30.0, respectively, with the horizontal. A weight of 200 N is hung 0.500 m from the left end where the 60.0 rope is attached. Find the tension in the ropes (T1 & T2) and the weight (W) of the bar. (Hint: Formulate three equations for the three unknowns, 2 equations for the 1st condition and 1 equation for the 2nd condition.)
I need your help expert. The system shown below is in equilibrium. Spring 3 is known to have a change in length of 10 cm. The magnitude of the compressive force in Spring 2 is 15% more than the magnitude of force P, while the magnitude of the compressive force in Bar 1 is 100 N less than that in Spring 2. If the spring constants of Springs 2 and 3 are 625 and 1200 N/m, respectively, determine the following: a. magnitude of forces P (in N) and F (in N) b. tension (in N) in cable ABC c. mass (in kg) of Block A d. compressive force in Bar 1 e. change in length (in cm) of Spring 2 Draw the complete FBD’s of Block A, Hook C and Pulley E. (Note: Below are the final answers, kindly match your answer on this. Thank you) Answer: P = 131.2831 N, F = 87.1569 N, TABC = 110.7024 N, mA = 15.6338 kg, F1 = 50.9756 N, s2 = 24.1561 cm
Statics-Two Force Members 1. Determine the force P required to maintain equilibrium of the pulley system, and the reactions at the ceiling. 2. Assume W=1.25kN 3. Show and clearly label all Free Body Diagram to determine solution.
Springs OA and OB are originally unstretched in a vertical position. Find the horizontal force, F, when the springs are held in the position as shown, given: k = 550 lb/ft, L1 = 0.6 ft, L2 = 1.3 ft
A spherical balloon 6 m in diameter is filled with gas weighing 5 N/m³. If the specific weight of air is 12N/m³, determine the maximum load that the balloon can lift (excluding its own weight). a. 1922.65 N b. 791.68 N c. 197.92 N d. 2375.05 N
Question 2) The figure shows a mechanical model of the Russel fracture traction device and the leg. The leg is held in balance in the position indicated by the two weights attached to the two cables. The combined weight of the leg and the cast is W=210 N. The horizontal distance between points A and B where the cables are attached to the leg is L=100 cm and the vertical distance is d=6 cm. Point C is the center of gravity of the cast and leg at three quarters of the L measured from point A (3L/4= 75 cm). The angle that cable 2 makes with the horizontal is measured as β=33°. Accordingly, in order for the leg to remain in balance in the shown position; a) Find the tensile force T1 in cable 1. (Write your result in N) b) Find the tensile force T2 in cable 2. (Write your result in N) c) Find the angle α of cable 1 with the horizontal. Response
Application of Equilibrium Solve for the value of unknown variables Given P1 = 1.39 KN P2 =6.05KN W1 = 4 KN/m Unknowns a. RAy , RBy , RBx , MB b. value of internal moment 2m to the left of support B