In the system, 900 L/min of oil is pumped with (s=0.92), from an underground storage tank to the first stage of a processing system. If the loss in the suction line is 1.5m and the loss in the discharge line is 4.5m. The suction line is 2.5” and the discharge line is 1.5”. Determine a) the outlet pressure in psi of the pump. b) The power in hp of the pump

In the system, 900 L/min of oil is pumped with (s=0.92), from an underground storage tank to the first stage of a processing system. If the loss in the suction line is 1.5m and the loss in the discharge line is 4.5m. The suction line is 2.5” and the discharge line is 1.5”. Determine a) the outlet pressure in psi of the pump. b) The power in hp of the pump

Principles of Heat Transfer (Activate Learning with these NEW titles from Engineering!)

8th Edition

ISBN:9781305387102

Author:Kreith, Frank; Manglik, Raj M.

Publisher:Kreith, Frank; Manglik, Raj M.

Chapter2: Steady Heat Conduction

Section: Chapter Questions

Problem 2.39P: The tip of a soldering iron consists of a 0.6-cm- diameter copper rod, 7.6 cm long. If the tip must...

See similar textbooks

Similar questions

An electric windshield defroster is used to remove 0.25-in of ice from a windshield. The properties of the ice are Tsat = 328F, uif = hif = 144 Btu/lbm, and v = 0.01602 ft3/lbm. Determine the electrical energy required per square foot of windshield surface area to melt this ice and remove it as liquid water at 328F. What is the minimum temperature at which the defroster may be operated? Assume that no heat is transferred from the defroster or ice to the surroundings.
What is the solution of this problem?
50 kg water per minute is to be heated from 30°C to 50°C by passing through a pipe of 2cm diameter. the pipe is heated by condensing the system keeping its inner surface at 100°C . find the length of pipe required. Take the following properties of water at mean bulk temperature of 40°C, density= 965 kg/m^3, v= 0.33*10^-6 m^2/sec , Cp= 4200J/kgK ,k= 0.585W/mK
Determine the MW and specific heat ratio of a gas whose Cv=1.386 kJ/kg.K and R= 0.485 kJ/Kg.K
An air compressor is designed to compress air (assumed to 100 kPa, 20 ° C at a pressure of 1 MPa). Heat losses to the environment are considered in advance to be about 10% of the input power to the compressor. The air enters at 50 m / s where the inlet area is 90cm2 and leaves 120m / s through an area of 5cm2. Determine: a) The air temperature at the outlet and the input power to the compressor. b) Heat coming out of the compressor 10% of the power
Water at a temperature of 400oF has a quality of 0.7. The internal energy of the water is ________ Btu/lbm.
An air compressor is designed to compress air (assumed to 100 kPa, 20 ° C at a pressure of 1 MPa). Heat losses to the environment are considered in advance to be about 10% of the input power to the compressor. Air enters at 50 m / s where the inlet area is 90 cm ^ 2 and exits at 120 m / s through an area of 5 cm ^ 2.Determine:a) The air temperature at the outlet and the input power to the compressor.b) Heat coming out of the compressor 10% of the power
Liquid A has a density of 0.85 kg/m3 and a specific sensible heatcapacitance (Cv) of 2.2 kJ/kgK. Liquid B has a density of 0.78 kg/m3and a specific sensible heat capacitance (Cv) of 1.8 kJ/kgK. Liquid A isat 22°C and liquid B is at 14°C. Equal volumes of both liquids are mixedtogether. What is the resulting temperature? answer is 18.6°C
1. Moist air enters a refrigeration coil at 89 F dry-bulb temperature and 65 F thermodynamic wet bulb temperature at a rate of 14oo cu ft per min. The surface temperature of the coil is 55 F . If 3.5 tons of refrigeration are available, find the dry bulb and wet bulb temperatures of the air leaving the coil. Assume sea level pressure.
A 10 ft³ vessel of hydrogen at a pressure of 300 psia is stirred by paddles until the pressure becomes 400 psia. Determine (a) ⧍U and (b) W. No heat is transferred, cv = 2.434 Btu/lb R Ans: ⧍U = 434 Btu; W = -434 Btu