In this circuit, three resistors receive the same amount of voltage (24 volts) from a single source. Calculate the amount of current "drawn" by each resistor, as well as the amount of power dissipated by each resistor: 192 292 3Ω ww Hilt 24 volts Complete the table below R1 R2 Voltage V (Volts) Current I (Amps) Power P (Watts) Resistance 10 R (Ohms) 202 R3 |3 Ω Total Req:

In this circuit, three resistors receive the same amount of voltage (24 volts) from a single source. Calculate the amount of current "drawn" by each resistor, as well as the amount of power dissipated by each resistor: 192 292 3Ω ww Hilt 24 volts Complete the table below R1 R2 Voltage V (Volts) Current I (Amps) Power P (Watts) Resistance 10 R (Ohms) 202 R3 |3 Ω Total Req:

University Physics Volume 2

18th Edition

ISBN:9781938168161

Author:OpenStax

Publisher:OpenStax

Chapter10: Direct-current Circuits

Section: Chapter Questions

Problem 37P: Consider the circuits shown below, (a) What is the current through each resistor in part (a)? (b)...

See similar textbooks

Similar questions

Consider the circuit shown in Figure P18.10. (a) Calculate the equivalent resistance of the 10.0- and 5.00- resistors connected in parallel. (b) Using the result of part (a), calculate the combined resistance of the 10.0-, 5.00-, and 4.00- resistors. (c) Calculate the equivalent resistance of the combined resistance found in part (b) and the parallel 3.00- resistor. (d) Combine the equivalent resistance found in part (c) with the 2.00- resistor. (e) Calculate the total current in the circuit. (f) What is the voltage drop across the 2.00- resistor? (g) Subtracting the result of part (f) from the battery voltage, find the voltage across the 3.00- resistor. (h) Calculate the current in the 3.00- resistor. Figure P18.10
Consider the circuits shown below, (a) What is the current through each resistor in part (a)? (b) What is the current through each resistor in part (b)? (c) What is the power dissipated or consumed by each circuit? (d) What is the power supplied to each circuit?
Consider the circuit shown in Figure P18.10. (a) Calculate the equivalent resistance of the 10.0- and 5.00- resistors connected in parallel. (b) Using the result of part (a), calculate the combined resistance of the 10.0-, 5.00-, and 4.00- resistors. (c) Calculate the equivalent resistance of the combined resistance found in part (b) and the parallel 3.00- resistor. (d) Combine the equivalent resistance found in part (c) with the 2.00- resistor. (e) Calculate the total current in the circuit. (f) What is the voltage drop across the 2.00- resistor? (g) Subtracting the result of part (f) from the battery voltage, find the voltage across the 3.00- resistor. (h) Calculate the current in the 3.00- resistor. Figure P18.10
A 1,00-?O voltmeter is placed in parallel with a 75.0kresistor in a circuit, (a) Draw a circuit diagram of the connection, (b) What is the resistance of the combination? If the voltage across the combination is kept the same as it was across the 75.0-kresistor alone, what is the percent increase in current? (d) If the current through the combination is kept the same as it was through the 75.0-kresistor alone, what is the percentage decrease in voltage? (e) Are the changes found in parts (c) and (d) significant? Discuss.
Choose the words that make each statement correct. (i) When two or more resistors are connected in series, the equivalent resistance is always [(a) greater than; (b) less than] any individual resistance. (ii) When two or more resistors are connected in parallel, the equivalent resistance is always [(c) greater than; (d) less than] any individual resistance.
Consider the circuit shown in the preceding problem. Write equations for the power supplied by the voltage sources and the power dissipated by the resistors in terms
Referring to the example combining series and parallel circuits and Figure 21.6, calculate I3in the following two different ways: (a) from the known values of I and I2 ; (b) using Ohm’s law for R3. In both parts explicitly show how you follow the steps in the Problem-Solving Strategies for Series and Parallel Resistors.
Why is the following situation impossible? A technician is testing a circuit that contains a resistance R. He realizes that a better design for the circuit would include a resistance 73R rather than R. He has three additional resistors, each with resistance R. By combining these additional resistors in a certain combination that is then placed in series with the original resistor, he achieves the desired resistance.
The circuit in Figure P27.34a consists of three resistors and one battery with no internal resistance. (a) Find the current in the 5.00- resistor. (b) Find the power delivered to the 5.00- resistor. (c) In each of the circuits in Figures P27.34b, P27.34c, and P27.34d, an additional 15.0-V battery has been inserted into the circuit. Which diagram or diagrams represent a circuit that requires the use of Kirchhoffs rules to find the currents? Explain why. (d) In which of these three new circuits is the smallest amount of power delivered to the 10.0- resistor? (You need not calculate the power in each circuit if you explain your answer.) Figure P27.34
A child’s electronic toy is supplied by three 1.58-V alkaline cells having internal resistances of 0.0200 in series with a 1.53-V carbon-zinc dry cell having a 0.100- internal resistance. The load resistance is 10.0 . (a) Draw a circuit diagram of the toy and its batteries, (b) What current flows? (c) How much power is supplied to the load? (d) What is the internal resistance of the dry cell if it goes bad, resulting in only 0.500 W being supplied to the load?
A 0.0200- ammeter is placed in series with a 10.00- resistor in a circuit, (a) Draw a circuit diagram of the connection, (b) Calculate the resistance of the combination, (c) If the voltage is kept the same across the combination as it was through the 10.00- resistor alone, what is the percent decrease in current? (d) If the current is kept the same through the combination as it was through the 10.00-resistor alone, what is the percent increase in voltage? (e) Are the changes found in parts (c) and (d) significant? Discuss.
A person with body resistance between his hands of 1.00 k accidentally grasps the terminals of a 20.0-kV power supply. (Do NOT do this!) (a) Draw a circuit diagram to represent the situation. (b) If the internal resistance of the power supply is 2000 , what is the current through his body? (c) What is the power dissipated in his body? (d) If the power supply is to be made safe by increasing its internal resistance, what should the internal resistance be for the maximum current in this situation to be 1.00 mA or less? (e) Will this modification compromise the effectiveness of the power supply for driving low-re si stance devices? Explain your reasoning,