In Vernier caliper, depth bar/ rod is used for * .measuring (ihäi 1)

Q: What is the mean dimension of a part if the maximum dimension is 137.646 mm, and the minimum…

A: Mean dimension: It is the dimension of the object from where the bilateral tolerance is equally…

Q: Find others Force applied =2.78N Area = 1mm?

A: Given data : Force=F Area=A   Required : Stress

Q: If 15.84 m^3 of oil weighs 47 kN, calculate Specific Gravity in 3 significant digits

A: given data Volume =15.84 m3 weight=45kn We have find spefic gravity. Of oil

Q: grams, and determine the length s of length. angular displacement B1, in deg ngular displacement B2,…

A: L=  16681 β=68 degree = β 1 + β2 L1= 0.298   (a) →   L= L1+ L2   L 2 =L-L1= 1661-0.298 = 1660.702…

Q: of diameter 50mm, specific gravity 0.7

A:

Q: what metric pipe size is approximately equivalent to a U.S. customary pipe size of 3/4"?

A: 34'' means 34 inch

Q: e height h2 (in): Grou

A: To determine the h2

Q: 80mm; de coefficient respective

A: d=80mm=0.08m.....same for delivery and suctionf=0.007Total length = 3m+6m=9m

Q: 1. For the shown hydraulic jack the gage pressure indicates 140 kpa how much kilograms should be…

A:

Q: n outside diameter of 70 m and :

A: here outer dia (70m) is >>>> inner dia (50mm). so the polar moment of inertia almost…

Q: y 800 lb - 40° Calculater for Fr 35°

A:

Q: if v=5s where s in meters finf a

A: Given:  v = 5 s where s in m

Q: Determine its minimum required diameter

A: for solution refer below images.

Q: Solve for EG, GH, and HJ

A:

Q: 18 бресуте пашу д slund is 1234. Determine density

A: Given data : Specific gravity=S.G Density of water=ρW   To find : Density of fluid

Q: ss of 1.5 tons and ction between the

A:

Q: Convert the ff.   8 ft 2.25 in as m

A: General conversion concept: 1 meter = 3.28084 foot 1 meter = 39.3701 in

Q: Identify the part belonging to vernier caliper. Measuring jaw O Movable jaw Clamping jaw O Stem

A:

Q: hing 3304 kN is If the block is 9

A: Weight of block = 3304 kN Weight of sea water displaced = volume of water x density Volume of water…

Q: The engine piston weighs 180 g. The machine speed is 4400 RPM. What is the maximum speed of the…

A:

Q: x= ky² 20 in. y = kx²

A:

Q: Describe the method of measuring the included angle '0 'by using three hard steel discs of rollers…

A: Draw the diagram to measure the included angle θ.

Q: 1. If the block is loaded with P = 282 kN, calculate the required dimension "b" of the key.   Write…

A:

Q: Express the quantity 556.2 x 10^-12s in ms.

A: Physical quantity = Numerical value X unit Let N = Numerical value u = Unit

Q: The depth measurement is done by _part of a Vernier Caliper. O Ratchet O Spindle Blade O Anvil

A: Depth can be measured by embeddings the depth bar into the gap you're measuring. After you alter…

Q: Find (Ix&ly), if a=30mm. a

A:

Q: e shear and mor

A: given:

Q: dimension of the block (in mm) is

A: Given; σ=500ε0.1where,  ε true strain Young modulus= rl is 200 GPa Block thickness=100 mm material…

Q: Compute ly (I bar sub y, in mm“, round-off to 2 decimal places) for the region shown. 80 mm 20 mm 60…

A:

Q: find the length of (20mm) diameter bore is equal to that in the (30 mm) diameter bore,

A:

Q: Findss 30 kN-m

A:

Q: 1. A cantilever machine component, of soli

A:

Q: Identify the part belonging to vernier caliper. Measuring jaw Movable jaw Clamping jaw O Stem

A: I need vernier caliber ,

Q: etermine the equivalent ement is oriented 20° clo

A:

Q: Pressure and Tempe O True O False

A: pressure and temperature are independent properties inside dome or not?

Q: Determine final dimension of the block in mm

A: Given data; Flow stress (in MPa) of a material is given by;                       =δ=500ε0.1  Young…

Q: If gage A reads -20 kPa, determine the elevations of points L, N, Q and D.

A:

Q: maximum eccentricity of the bush in mm will

A: Given;A brush was turned after mounting the same on a mandrel.The mandrel diameter=40-0.05+0.00…

Q: of 90mn : correc mm

A:

Q: Perform unit conversion. 1.4 in to mm

A: 1 inch=0.0254m 1m=1000mm

Q: If gage A reads -20 kpa, determine the elevations of points L, N, Q and Z.

A:

Q: Calculate the diameter e

A: Need to find diameter of Jet.

Q: Q6) For the presented figure: a-What is the accuracy of the vernier caliper. b- What is the value of…

A: A vernier calliper is used for the measurement of the length to an accuracy of 10-4 m. The vernier…

Q: Find the thickness of a cast iron cylinder 250 mm in diameter to carry a pr

A: Given Data⇒ Cast iron cylinder Diameter of cylinder(d)=250 mm Pressure (P)=0.7 Nmm2 Maximum tensile…

Q: 100 Ib 150 Ib 2 100 Ib 200 Ib

A: For solution refer below images.

Q: kness of dx, and (b) having a thickness of

A:

Q: ment at midspan (in kip-ft to one decimal) for the following bear kip/ft, L = 26 ft, and a = 6 ft.…

A:

Q: prove that relationship is correct -+ 2ax

A: GIVEN THAT:  Prove v2-vo2=2ax                                    v2=Final velocity…

Q: The best approximation for a,

A: Given data, Flywheel having mass=m Rim of radius=RConcentric disk like feature of radius=R/2Flywheel…

Q: force (in newton) normal to the slider axis

A: Given; Primary inertia forces of the slider are partially balanced by a revolving mass,m= 6 kg…

Metrology of Screw Threads

Screw threads are a series of ridges having the profile of a helix. This helix profile runs continuously along the length of a uniform solid or a hollow bar of a circular cross-section at periodic intervals. These helix ridges are also formed over a conical bar. These continuous helical ridges are termed threads.