Asap A rectangular block weighing 3304 kN is partially submerged in seawaterweighing 10.20 kN/m^3. If the block is 9 meters wide, 15 meters longand 3.6 meters high, determine the following:the submerged depth in m;the distance between the metacenter and the center ofbuoyancy in m;the metacentric height (m) if G is 2.7m from the bottomof the block; andis M above G? (yes or no)Note: Do not include units in your answers. Do not round offintermediate values and answer in four decimal places.

Weight of block = 3304 kN Weight of sea water displaced = volume of water x density Volume of water…

Answered: hing 3304 kN is If the block is 9

Engineering

Mechanical Engineering

hing 3304 kN is If the block is 9

International Edition---engineering Mechanics: Statics, 4th Edition

4th Edition

ISBN:9781305501607

Author:Andrew Pytel And Jaan Kiusalaas

Publisher:Andrew Pytel And Jaan Kiusalaas

Chapter8: Centroids And Distributed Loads

Section: Chapter Questions

Problem 8.121P: One side of the container has a 03-m square door that is hinged at its top edge. If the container is...

See similar textbooks

Related questions

Q: Find others Force applied =2.78N Area = 1mm?

A: Given data : Force=F Area=A Required : Stress

Q: B and the 0.5-in

Q: 0.9. Calculate its specific weight.

A: To find Specific Weight.

Q: Q/Draw S and B-M D 8 kuim

Q: force members in the bars and state the

A: Given: A struss To determine forces in all members

Q: Find (ly) for the shaded area

Q: n for the connecting ring at A and find (30Marks)

A: Solution : calculation: Apply equation of equilibrium. +↑∑Fy = 0WDsinθ+WFsinθ-WE =05sinθ+5sinθ =WE…

Q: The horsepower input of the power screw. The efficiency if the weight loaded is 10 kN.

A: This is consisting of Two threads twisted together in which the pitch is equal to twice the distance…

Q: уы =3 bafel beared Find the

A: Given data : Modulus of elasticity=E Bulk modulus=K Required : Poisson ratio

Q: The force applied on the spanner handle while tightening a nut generates Solect ono:

A: When we applied force at a distance from the pivot point then a turning moment has been generated.

Q: Solve for EG, GH, and HJ

Q: Please help solve only Part B of the problem. The correct answer for Part B is 109. (If needed the…

A: Givenλ=500nmθ is small so θ≈tanθ≈2×10-510-1≈2×10-4

Q: | X2 F m

Q: What would be the maximum weight W of the block, shown in the

A: Draw the FBD at point C Check the condition in which cable tension will be maximum Put the value of…

Q: machined surface. Determine the plate thickness t) for infinite life.

Q: The diameter of the large piston of a hydraulic jack is found to be 75 mm. A force of 58 N is…

A: Given that, Diameter of large piston, D2=75 mm,Force applied of small piston, F1=58 N,Load lifted by…

Q: d the enerry Jost in the slippin

Q: The engine piston weighs 180 g. The machine speed is 4400 RPM. What is the maximum speed of the…

Q: When a fulcrum is in the middle the force and distance are___. A. The same at both ends B.…

A: This is the class 1 type lever in which fulcrum in the middle .

Q: 1 kN load is applied to the plates in shear, what is

Q: To decrease the amount of force needed increase the of the inclined plane. distance or length O…

A: Given Data⇒ Inclined plane

Q: Deive equabon for height Rof Pate Governer useig Instantenous Centre Method.

Q: Calculate the K value for the hollow square shape, if the height is 25 mm and thickness is 2 mm.…

Q: work output from the

A: Given; An engine operates on the reversible cycles as shown in the figure.Find work output from the…

Q: values, and determine (a) the a B.M., and (b) the position

Q: In the Figure 6, the absolute force value in the bar AB is (in kN):

A: we have to calculate force in member AB of the truss.

Q: 8. GIVEN: Winch truck as shown. DETERMINE: 1. How much weight is left on the front axle when the…

Q: When the fulcrum is in the middle the force and distance are ____. A. The same at the ends B.…

A: when the fulcurum is in the middle the force and distance are the same at the ends.

Q: Calculate the forces on the rod by using the method of analytics

A: Data given-

Q: A body of 5.89N is lifted by two strings, making angles of 20 and 35° with the vertical. Compute the…

Q: dimension of the block (in mm) is

A: Given; σ=500ε0.1where, ε true strain Young modulus= rl is 200 GPa Block thickness=100 mm material…

Q: 8x10 °C is

Q: 1- State the differences between ropes elevator and hydraulic lift if th C

A: “Since you have asked multiple question, we will solve the first question for you. If you want…

Q: =D and F13 tube shown.

A: Given data F13 = 0.17 Length of cylinder = diameter of the cylinder

Q: A and d The teeth are of

Q: is find mo B) The angle btween ã=i+jtk ち-mi-k

Q: Determine final dimension of the block in mm

A: Given data; Flow stress (in MPa) of a material is given by; =δ=500ε0.1 Young…

Q: Find the tensien force in each 35 eable. A

Q: F (in kN) needed to move the block S is

A: Given, A block R mass 100 kg is placed on a block S of mass 150 kg as shown in fig. co-efficient of…

Q: 20 A force of 250 KN was needed to punch the hole through the 8 mm thick steel plate, as shown…

Q: 4 3 F OD 1 n E

Q: What would be the resultant force F of the triangular distributed load and its location of measured…

Q: g has a diameter of de up of semicirc having reluctar

Q: Find the thickness of a cast iron cylinder 250 mm in diameter to carry a pr

A: Given Data⇒ Cast iron cylinder Diameter of cylinder(d)=250 mm Pressure (P)=0.7 Nmm2 Maximum tensile…

Q: The reaction forces created by the unbalanced loads on the shaft in the A and B bearings are given…

Q: For the following Internal clovetails if b is yomm grater than C. M is 60 mm 25 mm less Find the…

Q: If the wire diameter of a compressive helical spring is increased by 2% the change in spring…

Q: kness of dx, and (b) having a thickness of

Q: rad/sec and having 20 te sure angle is 20° and m. on at the centre of the sha

Q: two blocks each weighing 1.5 kN

A: Find the mass of each block.

Concept explainers

Mechanisms of heat transfer

Heat transfer is an essential discipline in thermal engineering that deals with the transfer, conversion, usability, and creation of heat or thermal energy. Transfer of heat occurs through various mechanisms like conduction, convection, radiation, and change of phases. All these mechanisms have distinct characteristics, but these mechanisms can simultaneously occur in an identical system.

Question

100%

Asap

A rectangular block weighing 3304 kN is partially submerged in seawater
weighing 10.20 kN/m^3. If the block is 9 meters wide, 15 meters long
and 3.6 meters high, determine the following:
the submerged depth in m;
the distance between the metacenter and the center of
buoyancy in m;
the metacentric height (m) if G is 2.7m from the bottom
of the block; and
is M above G? (yes or no)
Note: Do not include units in your answers. Do not round off
intermediate values and answer in four decimal places.

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

SEE SOLUTION Check out a sample Q&A here

Step 1

VIEW

Step 2

VIEW

Step 3

VIEW

Step by step

Solved in 3 steps with 4 images

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, mechanical-engineering and related others by exploring similar questions and additional content below.

Similar questions

One side of the container has a 03-m square door that is hinged at its top edge. If the container is filled with water, determine the smallest force F that must be applied to the bottom edge of the door to keep it closed.
A rectangular car is 3 m. long by 1.5 m wide and 1.5 m deep. If friction is neglected and the car rolls down a plane with an inclination of 20 degrees, what is the inclination of the water surface if the car contained 0.60 m depth of water when the car was horizontal?
An elliptical plate, major axis 6 feet and minor axis 4 feet, is submerged vertically until its minor axis lies in the surface of the water (weight density =p Ib/fr3). Determine the appropriate integral to be used to determine the force on one side of the submerged
A semicircular 40-ft-diameter tunnel is to be built under a 150-ft-deep, 800-ft-long lake. Determine the total hydrostatic force acting on the roof of the tunnel.
A triangular wooden body (S=0.80) is placed in water in theposition indicated in the figure. If the width of the body is 7.0 m,determine if the same for this position is stable or not indicating themetacentric height (YM).
EMERGENCY!!!! The cover in the figure is hinged at the center O and has a fixed width w = 5 m. The equation of the surface is x = y2 / a (a = 3 m), the depth of the water to the right of the lid (D = 4 m). If the weight of the lid is neglected, it is necessary to keep the lid in balance. Find the size of the force (Fa) required, as shown. Take the density of the water as 999 kg / m3.
A semicircular gate with a diameter of 6 ft is installed at 50º as shown below. The top of the gate is 5 ft below the water surface. Determine the resulting hydrostatic force and the location of the center of pressure on the gate.
End D of a 2.5 long uniformly plain wooden rod( s.g=0.7) is held 0.3m below the surface of still water. (a.) How much of the rod remains above the water surface? (b.) if the rod diameter is 25mm what force of D is required to hold it in place ?
11. A metal plate has the shape of an equilateral triangle with a side length of 2 meters. It is submerged verticallyin water so that the base of the triangle is 5 meters below the surface of the water. How much hydrostaticforce is exerted against the plate due to the hydrostatic pressure of the water? this is the answer but I'm sure how to solve for it F = ρg(5sqrt(3) − 1) N
An oil tanker 3m wide 2 m deep and 10 m long contains oil of density 800 kg/m3, if the tanker is closed and completely filled with the oil and accelerated horizontally at 3m/s2. a.) determine the total liquid thrust (hydrostatic force) on the front end. (in kN) b.) determine the total liquid thrust (hydrostatic force) on the rear end. (in kN)
A 4-m-long quarter-circular gate of radius 4 m and of negligible weight is hinged about its upper edge A, as shown in the figure. The gate controls the flow of water over the ledge at B, where the gate is pressed by a spring. Determine the minimum spring force (in N) required to keep the gate closed when the water level rises to A at the upper edge of the gate. Round your answer to 2 decimal places.
Hydrostatic: A 2-m-wide, 3-m-high vertical rectangular gate has its top edge 2 m below the water level. It is hinged along its lower edge. What force, acting on the top edge, is necessary to hold the gate shut?