I need the answer as soon as possible Q1. Choose the correct answer (Answer any TEN):1.increases as the length of channel increases. (interference, distortion, additive noise, attenuation).2. 100% modulation is produced in AM when carrierfrequency exceeds signal frequency, amplitude equals signal amplitude, amplitude exceeds signalamplitude).3. A 10 MHz carrier of peak value of 10 V is amplitude modulated by a 10 kHz signal of amplitude 5 V.The amplitude of each sideband frequency is4. A Phase-Locked Loop (PLL) is a feedback circuit consisting ofvCo, all of the above).5. The line connecting the positive and negative peaks of the carrier waveform is called(Peak line, Maximum amplitude, Modulation index, Envelope)6. Thermal noise power is proportional to (T, 1/T, T, T'2)7. Which of the following is an advantage of SSB over DSB? (No change in spectrum space, Reduce inspectrum space, Carrier is suppressed, Power is not wasted on the carrier).8. Which one of the following is not true with respect to SSB signal? (Hard to demodulate, Less power,Carrier is suppressed, Very low range).(frequency equals signal frequency,(2.5 V, 1.25 V, 1.5 V, 6 V).(phase detector, low-pass filter,

increases as the length of channel increases. (interference, distortion, additive noise, attenuation). (frequency equals signal frequency, 2. 100% modulation is produced in AM when carrier frequency exceeds signal frequency, amplitude equals signal amplitude, amplitude exceeds signal amplitude). 3. A 10 MHz carrier of peak value of 10 V is amplitude modulated by a 10 kHz signal of amplitude 5 V. The amplitude of each sideband frequency is (2.5 V, 1.25 V, 1.5 V, 6 V).

increases as the length of channel increases. (interference, distortion, additive noise, attenuation). (frequency equals signal frequency, 2. 100% modulation is produced in AM when carrier frequency exceeds signal frequency, amplitude equals signal amplitude, amplitude exceeds signal amplitude). 3. A 10 MHz carrier of peak value of 10 V is amplitude modulated by a 10 kHz signal of amplitude 5 V. The amplitude of each sideband frequency is (2.5 V, 1.25 V, 1.5 V, 6 V).

Introductory Circuit Analysis (13th Edition)

13th Edition

ISBN:9780133923605

Author:Robert L. Boylestad

Publisher:Robert L. Boylestad

Chapter1: Introduction

Section: Chapter Questions

Problem 1P: Visit your local library (at school or home) and describe the extent to which it provides literature...

See similar textbooks

Similar questions

How to calculate the efficiency in frequency modulation and what is the highest value for efficiency in frequency modulation
A) what name the modulation scheme in the blue curve in A and C B) what is the duty cycle in B C) What is the sampling Frequency in B D) write and equation that represent the modulated signal in B solve all parts or will dislike
Please assume modulation.
what happens when the modulation order is increased for a modulated signal?
Q: Explain in details with all figures ind equations the modulation index of Amplitude Modulation (AM) and then show the AM wave when the modulation index > 1, modulation index < 1 and modulation index
The maximum deviation allowed in a frequency modulation system is 100 kHz; the modulating signal frequency is 10 kHz. The bandwidth requirement as per Carson's rule will be?
Briefly explain what it is Single Sideband Modulation
Determine four distinct types of modulation processes.
An analog signal is to be coded by an ADC. The signal contains significant frequencies up to 6MHz. The quantization error in any one sample value must be within ± 0.5% of the peak-to-peak amplitude range of the ADC. How many binary digits must each sample contain? Apply (or equate) the formulas:Δ = Xmax - Xmin / L - 1where Xmax - Xmin = peak-to-peak amplitude range (XRange)eq[n] = Δ/2 (maximum quantization noise)eq[n] = 0.005 XRange
(a) Plot the even and odd parts of the signal of Figure
1-6.* Draw two cycles of the timing diagram for a digital signal that continuously alternates between 0.2 V (binary 0) for 2 ms and 4.4 V (binary 1)for 4 ms.1-7.* Measure the period, frequency, and duty cycle of the waveform in1-6. Assume the active part of the waveform is HIGH.
Write an 8051 ASM program to load the timer 1 in order to generate 2000 Hz square wave as given in Figure. The square wave should be generated on pin 2 of port 3. Assume the crystal frequency is 16 MHz. ON 4* Delay Delay