induction motor is given Figure next to. The rotational, core, friction and windage losses except the load losses (stator and rotor) are neglected. The motor runs at full load speed of 1700 r.p.m. The inserted resistance R_ins in the rotor circuit to start from B on curve 2 equal tog Speed-torque characteristic 1800 1600 1400 1200 1000 800

induction motor is given Figure next to. The rotational, core, friction and windage losses except the load losses (stator and rotor) are neglected. The motor runs at full load speed of 1700 r.p.m. The inserted resistance R_ins in the rotor circuit to start from B on curve 2 equal tog Speed-torque characteristic 1800 1600 1400 1200 1000 800

Introductory Circuit Analysis (13th Edition)

13th Edition

ISBN:9780133923605

Author:Robert L. Boylestad

Publisher:Robert L. Boylestad

Chapter1: Introduction

Section: Chapter Questions

Problem 1P: Visit your local library (at school or home) and describe the extent to which it provides literature...

See similar textbooks

Similar questions

A three-phase induction motor, at rated voltageand frequency, has a starting torque of 140 percentand a maximum torque of 210 percent of full-loadtorque. Neglect stator resistance and rotational lossesand assume constant rotor resistance. Determinea. The slip at full load.b. The slip at maximum torque.c. The rotor current at starting as a percentage offull-load rotor current.
A three-phase induction motor, operating at rated voltage and frequency, has a startingtorque of 1.35 times and a maximum torque of 2.2 times, both with respect to its rated-loadtorque. Ignoring the effects of the stator resistance and rotational losses and assumingconstant rotor resistance, determine the slip rated load, and the rotor current at starting (as a percentage of the rotor current at rated load). The slip at maximum torque is 0.343 if that helps.
a. A three-phase, 220-V, 60-Hz induction motor runsat 1,140 r/min. Determine the number of poles (forminimum slip), the slip, and the frequency of therotor currents.b. To reduce the starting current, a three-phasesquirrel cage induction motor is started byreducing the line voltage to Vs/2. By what factorare the starting torque and the starting currentreduced?
Briefly discuss the changes in the power factor of a three-phasesquirrel cage rotor induction motor from start-up to rated load.
Objectives: To perform the speed control test on slip ring induction motor by rotor resistance control method. Plot the motor speed characteristics at different values of applied resistance in slip ring of induction motor. Can you explain what happened here? (image below)
What are the differences in power factor, torque, speed, output power and efficiency of star connection and delta connection of induction motors?
What is Equation to find Slip, Output horse power, Torque, Stator current, p.f, Efficiency, From this result and we have Frequency and poles this result from load test of an induction motor
The rotor resistance and reactance per phase of a 4-pole, 50-Hz, 3-phase induction motor are 0.025 ohm and 0.12 ohm respectively. Make simplifying assumptions, state them and : (i) find speed at maximum torque (ii) find value of additional rotor resistance per phase required to give three-fourth of maximum torque at starting. Draw the equivalent circuit of a single-phase induction motor.
Attempt the following: Draw and explain a complete equivalent circuit of single phase induction motor? Explain the Starting of Single Phase Induction Motors?
1. What is the formula for torque production in a single-phase induction motor? Draw a vector diagram for capacitor start single-phase induction motor.2. Which type of starter is popular for using in induction motor and why?
A 4-pole, 50 hz, 3-phase induction motor has a slip-ring rotor with resistance and standstill reactance of 0.04 ohm and 0.2 ohm per phase respectively. Find the amount of resistance to be inserted in each rotor phase to obtain full-load torque at starting. What will be the approximate power factor in the rotor at this instant? The slip at full-load is 3 percent.
What are the advantages and disadvantages of using the following types of motors? split-phase motor Answer 1Choose...Advantage: good starting torque; Disadvantage: costAdvantage: stalls without damage; Disadvantage: low starting torqueAdvantage: cost; Disadvantage: moderate starting torqueAdvntage: good running efficiency; Disadvantage: difficult to reverse shaded-pole motor Answer 2Choose...Advantage: good starting torque; Disadvantage: costAdvantage: stalls without damage; Disadvantage: low starting torqueAdvantage: cost; Disadvantage: moderate starting torqueAdvntage: good running efficiency; Disadvantage: difficult to reverse PSC motor Answer 3Choose...Advantage: good starting torque; Disadvantage: costAdvantage: stalls without damage; Disadvantage: low starting torqueAdvantage: cost; Disadvantage: moderate starting torqueAdvntage: good running efficiency; Disadvantage: difficult to reverse capacitor-start–capacitor-run motor Answer 4Choose...Advantage: good…