Instructions: Follow Given-Required-Solution format for your computation. Complete FBD for full credit. Problem: The resultant of the three concurrent forces acting on the eyeball is the force R = 800j N. Determine the magnitude of the force P and the angle that specifies the direction of the 900-N force.

Q: 1. Determine the magnitude of the resultant force acting on the screw eye. 60° 2 kN 6 kN

A: To find resultant

Q: 2230 kN 80 mm 1.75 m X 90 mm Z 2230 kN Y

A:

Q: íf F, = 600 N and = 30°, determine the magnitude of the resultant force acting on the eyebolt. F1…

A:

Q: 30 kN 20 kN 20 kN D m E m F L K H

A:

Q: Part A The simply supported shaft has a moment of inertia of 21 for region BC and a moment of…

A:

Q: Problem (8.5): A simple beam AB supports two concentrated loads P at the positions shown in the…

A:

Q: 50 kN 100 kN B -6 m- 100 kN A 100* 307 kN

A:

Q: Given figure shown. The magnitude of the Resultant Force is 48.5898 kN. The angle e is 40 degrees…

A:

Q: The blocks shown below are connected by cords passing over frictionless pulleys. The coefficients of…

A: F.B.D

Q: Given figure shown. The magnitude of the ResulItant Force is 48.5898 kN. The angle e is 40 degrees…

A: Given  Resultant force R = 48.5898 KN Angle theta = 40 degrees Y component of total resultant force…

Q: A = 3 B = 4 C = 1 D = 0   kindly answer the magnitude and if possible the forces

A:

Q: Find the bar forces and the type of bar force.complete the table and show complete and clear…

A:

Q: ased on the following illustration, solve the following questions: 15kN 5kN/m 5m 5m 5m the beam is…

A:

Q: c kN bkN/m B "a" m "a" m

A:

Q: Using Double Integration Method derive an expression for the following: a) Reaction at propped…

A:

Q: Based on the graph, what is the best shape to lower the force acting ? Circle or rectangular? Make a…

A: For Circular Shape Column Centre of Gravity (hc) Diagonal Depth Centroid (yc) Diagonal Depth…

Q: Part 4 (problem solving) Problem 1 Calculate sag correction for a 30 m steel tape under a pull of 80…

A:

Q: The top block weighs 50 16 while the bottom box weighs 25 Ib. The coefficient of static friction for…

A: as the block is present in the rest position  so we have to consider static friction

Q: H.W: Replace the 600 Ib force of Figure below by a force through A and a couple whose forces act…

A:

Q: 40 KN 32 AN / m E C D 2m

A:

Q: 3. ( ø measured from the horizontal x axis. Refer to Fig. 3 below. Using Component Method, determine…

A:

Q: What is the normal force exerted by the roller? 25 KNim 150 KN 10 m Select one: a. 149.30 kN b.…

A:

Q: A Triangular gate having a horizontal base of 1 30 m and an altitude of 2 m is inclined 45 o from…

A:

Q: A. What force does the crossbar exert on each beam?

A:

Q: Determine the deflection @C using Moment Area Method. (Your final answer should be in "mm") 8 kN/m 3…

A: Introduction- One of the most successful ways for determining bending displacement in beams and…

Q: 6. Determine whether the block shown is in equilibrium and find the magnitude and direction of the…

A:

Q: The intensity of the distributed load on the simply supported beam varies linearly from zero to wo =…

A: Apply double integration method ,  Integrate two times to obtain displacement and rotation.

Q: Replace the two forces acting on the bent pipe by a single equivalent force R. Specify the distance…

A:

Q: A section of a reinforced concrete elevator shaft is shown in the figure. Compute the following: a.…

A: Note: Hi! Thank you for the question. We’ll answer the first two question. As third question seems…

Q: Compute the total elongation caused by an axial load of 147 kN applied to a square bar, tapering…

A:

Q: 2.5 kips 500lb A 12" 500 cm 200 am

A: Note: Hi! Thank you for the question, As per the honour code, we are allowed to answer three…

Q: The simply supported concrete beam shown in the figure has an effective depth of 600 mm and a…

A: Given effective depth d=600 mm and widthn b=300 mmstress in concrete fc=28 MPa and in steel fy=420…

Q: Portal Method: Analyze the building frame shown by the portal method, and answer the following…

A: The Portal Method: The Portal method was presented by Albert Smith in the Journal of Western Society…

Q: Answer Five Questions Q1/When the two forces are placed on the beam, the diameter of the A-36 steel…

A:

Q: 1500 N 240 mm 300 N 30 120 mm 1000 N

A:

Q: Determine the magnitude and direction of force, F, from the given force triangle, if the resultant…

A:

Q: t A is 10m/s. The block is released at B and passes through an upward circular arc BC (tangent to B)…

A: Draw the figure

Q: 国 SET A SET B SET C 888 F1 150 100 200 F2 350 250 350 888 F3 300 350 250 888 F4 350 400 400 888

A:

Q: H.W: Replace the 600 Ib force of Figure below by a force through A and a couple whose forces act…

A:

Q: A cantilever beam 50 mm wide and 80 mm deep is 2 m long. It carries a uniformly distributed load…

A: The width of the beam is b=50 mm. The depth of the beam is b=80 mm. The length of the beam is L=2 m.…

Q: the weight of the file cabinet is 60 lbs and G represents its center of gravity the coeffiecent of…

A:

Q: I kir Ok 05 kir 20 10 10 10

A: An axial loaded beam is given and it has been asked to draw axial force diagram, please refer step 2…

Q: A. Force System 1. Determine the components of the 500N force directed up to the right as shown in…

A:

Q: For the beam and loadings shown and assuming El is constant, answer the following questions. Use 5…

A:

Q: Compute the total elongation caused by an axial load of 142 kN applied to a square bar, tapering…

A:

Q: A 20-lb force is applied to the control rod AB as shown. Knowing that the length of the rod is 9 in.…

A:

Q: Fill in the blanks / identification: The weight of the suspended pipe in figure shown is 450 N. a.…

A: Given Weight of the suspended pipe = 450 N Angles between the wires. To Determine Tensile force in…

Q: Replace this loading by an equivalent resultant force and specify its location, measured from point…

A:

Q: 6-6 Om 天ー45。 O'E I li25m 2,50 m そく 18ちm W= 120 KN と 0.40m

A: Find T,F and C?