is apple showr on member ABC that is held by the 15-mm diameter cable. The pin at the support C is in double shear and its diameter is 20mm. Determine the shear stress at pic C. Express your answer in "MPa" to the nearest whole number. Note: Use the rule in rounding-off numbers (normal rounding-off). DO NOT PUT A UNIT IN YOUR ANSWER, only the numerical value is required. * 30

is apple showr on member ABC that is held by the 15-mm diameter cable. The pin at the support C is in double shear and its diameter is 20mm. Determine the shear stress at pic C. Express your answer in "MPa" to the nearest whole number. Note: Use the rule in rounding-off numbers (normal rounding-off). DO NOT PUT A UNIT IN YOUR ANSWER, only the numerical value is required. * 30

Mechanics of Materials (MindTap Course List)

9th Edition

ISBN:9781337093347

Author:Barry J. Goodno, James M. Gere

Publisher:Barry J. Goodno, James M. Gere

Chapter5: Stresses In Beams (basic Topics)

Section: Chapter Questions

Problem 5.9.3P: A vertical pole consisting of a circular tube of outer diameter 5 in. and inner diameter 4.5 in. is...

See similar textbooks

Similar questions

A circular pole is subjected to linearly varying distributed force with maximum intensity t0. Calculate the diameter daof the pole if the maximum allowable shear stress for the pole is 75 M Pa.
A pole is fixed at the base and is subjected to a linearly varying distributed force with maximum intensity of q0and an axial compressive load P = 20 kips at the top (see figure). The pole has a circular cross section with an outer diameter of 5 in. and an inner diameter of 4.5 in. Find the normal stresses on the surface of the pole at the base at locations A and B.
(D) The pin used at B has an ultimate shear strength of 58 ksi. If a factor of safety of 2.5 is required, determine the allowable shear stress in this pin. in ksi (E) The pin used at B is a double shear pin connection. Determine the minimum pin cross-sectional area, and the corresponding minimum pin diameter that can be used at B. (Amin IN in.2 and dpin IN in.) (F) Determine the deformations in rods (1), (2), and (3) when load P equals Pmax from Letter C. ANSWERS in inch (G) Using the results from Letter F, determine the deflections of Joint B and Point D. ANSWERS in inch
A simple truss is subjected to a vertical load F = 500 lb.Determine the minimum diameter of the pin at C if theallowable shear stress on the pin is 20 psi.Answers: d =___________________
A shaft composed of three segments and fastened to rigid supports. Determine the maximum shear stress developed in each segment. (Please don't skip any mathematical step and please show all the working)
The piece of wood shown below was used in an experiment. During the test it sheared parallel to the wood grain along the dashed line. Determine the average shear stress (in psi rounded to the nearest whole number) on that failure plane for a maximum load of P = 1750 lb. The dimensions of the wooden specimen are t = 2.5 in. and L = 5 in.
A 3-m long thin-walled tube has an equilateral triangular cross-section with a constant thickness of 10 mm. If each side of the triangle is 200 mm measured at the median line and the allowable torsional stress is 40 MPa, what is the angle of twist in radians? (Use G = 70 GPa)
The right-angle bar is supported by a pin at B and a roller at C. what is the maximum safe value of the load P that can be applied if the shear stress in the pin is limited to 20,000 psi? the 3/4 -diameter pin is in double shear.
The circular column is subjected to a compressive force of 5kN if the stress in the column is limitedto 17.63MPa, what is the limiting value of diameter d?
Consider the wooden member subjected to a tensile load P = 11.00 kN. Determine the shear stress at the inclined section as shown.
A steel pipe 120 mm external diameter and 60 mm internal diameter is subjected to an internal pressure of 15 N/mm2 and an external pressure of 5 N/mm2. Determine and sketch curves showing the distribution of the radial and circumferential stress across the section using Lame’s equations.
For the connection shown, determine the average shear stress in the 0.75-in.-diameter bolts if the load is P = 64 kips.