A 7/8-in diameter bolt, having a diameter at the root of the threads of 0.731 in., is used to fasten two timbers together. The nut is tightened to cause a tensile stress of 18 ksi in the bolt. Compute the shearing stress (ksi) in the head of the bolt and in the threads. Also, determine the outside diameter of the washers (inches) if their inside diameter is 9/8 in. and the bearing stress is limited to 800 psi. 1/2 in 5/8 in

A 7/8-in diameter bolt, having a diameter at the root of the threads of 0.731 in., is used to fasten two timbers together. The nut is tightened to cause a tensile stress of 18 ksi in the bolt. Compute the shearing stress (ksi) in the head of the bolt and in the threads. Also, determine the outside diameter of the washers (inches) if their inside diameter is 9/8 in. and the bearing stress is limited to 800 psi. 1/2 in 5/8 in

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

The lap joint shown is fasted by 20mm diameter rivets. Calculate the maximum safe load P that can be applied if the shearing stress in the rivet is limited to 96MPa and the bearing stress is limited to 124 MPa. Assume the Applied load is uniformly distributed among the four rivets.
Two steel springs arranged in series supports a load P. The upper spring has 12 turns of 20-mm-diameterwire on a mean radius of 100 mm. The lower spring consists of 10 turns of 25-mm diameter wire on amean radius of 75 mm. If the maximum shearing stress in either spring must not exceed 300 MPa,compute the maximum value of P and the total elongation of the assembly. Use approximation formulaand G = 83 GPa. Compute the equivalent spring constant by dividing the load by the total elongation.
A helical spring is made by wrapping steel wire 20 mm in diameter around a forming cylinder 18O mm indiameter. Compute the number of turns required to permit an elongation of 180 mm without exceeding ashearing stress of 140 MPa. Use G=83 GPa. Use the first equation of shearing stress under helical spring.
A flexible cable and rigid boom system is used to lift a load of 65kN at the end of Boom at point C. Points A and B are considered pinned in nature. The allowable shearing stress at all bolts are 250MPa and the allowable bearing stress at all bolts are 300MPa. Note that the initial position of boom is horizontal and segment A and B are vertical. Determine the horizontal reaction at A. 3. Determine the vertical reaction at A.
If the allowable normal stress is 120MPa and the allowable shear stress is 60MPa, what is the B diameter of pin?
Compute the tensile stress for the rod shown in Fig. 1 at section A-A, the shearing stress across section B, the compressive stress between the pin and the rod, and the compressive stress between the pin and the yoke. Given n = 1 (3 / 4) in., a = (15 / 32) in., e = (27 / 32) in., b = (15 / 16) in., d = (19 / 32) in., f = 1".
A flanged bolt coupling consists of ten 20-mm diameter steel bolts spaced evenly around a bolt circle 400 mm in diameter. Determine the maximum shear stress formed in a 200-mm diameter shaft if the allowable shearing stress in the bolts is 40 MPa. Show complete solution and figure.
Illustrate and completely solve the problem! Write legibly or type written the solutions. The shaft assembly is made from a steel tube 1 in. in diameter, which is bonded to a solid brass core 0.5 in. in diameter. If a torque of 250 lb-ft is applied at its end, determine the maximum shear stress in psi experienced by the assembly. Take G for steel at 11.4 x 103 ksi and G brass at 5.2 x 103 ksi.
In the clevis shown in the figure, determine the minimum bolt diameter and minimum thickness of each yoke that will support a load P = 55kN without exceeding a shearing stress of 70 MPa and a bearing stress of 140 MPa
A flanged bolt coupling consists of seven 12-mm diameter bolts arranged on a bolt circle 300 mm in diameter, and five 12-mm diameter bolts on a concentric bolt circle 250 mm in diameter, Calculate the torque that can be applied if the allowable shearing stress in the bolt is 60 MPa.(detailed solution w/fbd)
The allowalbe tensile stress for a 62.5mm diameter bolt with a thread length of 5.5mm is 207 MPa. The allowable shear stress of the material is 103 MPa. Compute the allowable shearing load on the thread.A. 4.35 kNB. 6.35 kNC. 2.45 kND. 5.56 kN
a. Determine the absolute maximum shear stress at segment AB (in MPa) b. Determine the absolute maximum shear stress at segment BC (in MPa) c. Determine the angle twist of Gear C relative to A (in degrees) note: indicate the free body diagram