3-15. An L6 x 6 × 1/2 is used as a tension member, with one gage line of 3/4-in Ø boltsin each leg at the usual gage location (see Table 3.1). What is the minimum amount ofstagger, s, necessary so that only one bolt need be subtracted from the gross area of theangle? Compute the net area of this member if the lines of holes are staggered at 3 in.(Ans. s = 4.77 in, A, = 5.05 in?)

Answered: Image /qna-images/answer/f65947c5-1673-4ac2-9113-6369af1e5ec3.jpg

Answered: Is used ch leg at the usual gage

Engineering

Civil Engineering

Is used ch leg at the usual gage

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Related questions

Q: Get the shear and moment function and draw the shear and moment diagram for the beam.

A: Drawing of SFD and BMD###

Q: Calculate the strength of a discontinuous strut of length 3.2 m. The strut consists of two unequal…

Q: The bolted connection shown is a bearing type connection. Which of the following best gives the…

A: Answer We are given M20 A 490 group bolts Number of bolts = 6 Calculations shown below

Q: Example 4.5 4.8 m. The member is to be used in a transmission line tower and is as shown ends are…

Q: Q. As the Structural Engineer of ABC Engineering Consulting firm, you are required to design a…

Q: Determine the deflection at joint C given the cross-section of the beam and assuming E = 200 GPa. 12…

Q: A right square pyramid (SG = 0.6) has a base with sides 90cm long. The height of the square pyramid…

Q: Problem 2: A solid circular shaft is acted upon by the torques as shown. If G= 12, 000 ksi…

Q: 3-11. The 7/8 x 14 plate shown in Fig. P3-11. The holes are for 7/8-in Ø bolts. (Ans. 10.54 in?) |3…

A: Calculate the net area along each possible path from one end to other end of plate. The least one…

Q: 10-10. Determine the reactions at the supports, then draw the moment diagram. Assume the support at…

Q: The sieve analysis of soil and the liquid and plastic limits of the fraction passing through the No.…

A: % Passing no 10 sieve = 100 % Passing no 40 sieve = 92 % Passing no 200 sieve = 80 Liquid limit = 56…

Q: Determine the horizontal component of the total hydrostatic force (kN) acting on the curved surface.…

Q: 3. For the dam retaining water as shown in the figure, the foundation soil is permeable; assume…

Q: For the cantilever beam shown on the above figure, determine the following: Shear force at B…

Q: at the end of the curve lies at Station 18+533.71 and elevation 172.06 meters. The grade of the back…

A: Find…

Q: Astronouts who landed on the moon during the pollo 15, 16 and 17 missions brought bock a lorge…

Q: The braking distance of a car from 100 km/h is 50 m assuming the pavement is level. (a) if the…

Q: C 6 m B A 5 m 3 m 6 m 3 m Fiq 23 - Prob 23

Q: PROBLEM For the beam loaded as shown, do the following 1. Determine the values of shear and moment…

A: NOTE : Since you have posted a question with multiple sub-parts, we will solve the first three…

Q: er mete on the

Q: Please

Q: Draw the shear force and bending moment diagrams for the beam shown in your solution sheets. Provide…

Q: The tank shown in the accompanying figure is being filled by Pipes 1 and 2. If the water level is to…

A: For no change in water level in tank. The discharge entering the tank must be equal to discharge…

Q: According to Euler's column theory, the crippling load for a column of length (I) fixed at both ends…

Q: Determine the a) magnitude load P to be applied, and b) the normal stress on plane AB and the…

Q: SET P1, kN M1, W1, L1, L2, L3, L4, m X-Limit 1 X-Limit 2 kN.m kN/m A 70 150 15 2.50 Osx;<L2 L3<X2SL4…

Q: 1. The vector position of a particle varies in time according to the expression =4i-8 j, where ř is…

Q: For a data of maximum recorded flood of a river, the mean standard deviation are 4200 m3/s and 1705…

Q: s support the rigid L-shaped bracket BCF as shown in the figure. Determine the stress in rod DE…

Q: 27. A certain machine has book value of P173,205.08 after 5 years and P82,187.59 after 8 years. The…

Q: For the beam shown, derive the expressions for V and M, and draw the shear force and bending moment…

Q: quired to displace the top plug to

Q: 5 prs D Question 3 Determine the vertical component of the total hydrostatic force (kN) acting on…

A: The vertical force will be equal to weight of volume of liquid supported over the curved surface.

Q: Principles of Reinforced/ Pre-stressed Concrete Aside from added strength, cite at least 3 most…

A: 3 practical reasons of adding compression steel reinforcement in beams are :- (1) to improve long…

Q: Please avoid rounding välu during the course of solution proper as much as possible. Write the final…

Q: What diameter of a standard, sharp-edge orifice will be required to produce a discharge of 1.25 cfs…

Q: Design a cased <olumn to <arry an axial load of T100 kN. The <olumn is 5 m long and restrained in…

Q: At the instant shown, which person experiences the largest force from his or her chair (back and…

Q: $0 P. 50 25 100 25

Q: flood of a river, the mear standard deviation are 4200 and 1705 m³/s respectively. Gumbel's extreme…

Q: SINE LAW * A civil engineer desires to measure the height of a tower observing a vertical angle at…

Q: Determine the vertical component of the total hydrostatic force (kN) acting on the curved surface.…

Q: Which of the following best describes the structural design process? Sourcing financing stage,…

A: This question is asking about various stages following during structural design process

Q: 25. A structure cost P12,000 new. It is estimated to have a life of 5 years with salvage value at…

A: Cost of structure = 12000 Estimated life = 5 years Salvage value = 1000 To Find :- Book value at the…

Q: alculate the weight of moist sand that should be in a batch if the design mix requires concrete to…

A: Given Water cement ratio= 0.45 Dry gravel= 1258kg/m3

Q: Three hills, A, B and C, have elevations of 660 m., 630 m., and 600 m., respectively. B is in…

Q: Following are the results from the liquid and plastic limit test for a soil. No. of blows (N)…

A: Given Natural water content 26.5 % Liquid limit is calculated corresponding to no.of blows 25

Q: Problem 1: Determine the magnitude of the resultant force per meter length acting on the…

Q: The speed-density relationship for a particular road was found to be : u = 42.76 - 0.22 k, where u…

Q: If Line AB is due North, the following are the interior angles the polygon ABCDE? The following…

Concept explainers

Introduction to Engineering Design

Students are often confused with engineering and design. The term engineering design has two words with different meanings, engineering, and design. The term engineering implies applications of laws and principles of science to design and analyze physical structures and components. In civil engineering, students apply the concept of physics and chemistry to design and build structures and buildings. In engineering disciplines, the term design means determining the dimensions, loads, and associated influences on the component due to the applied loads such as stresses and deformations. The estimation of such parameters is crucial to make the component or structure foolproof.

Question

3-15. An L6 x 6 × 1/2 is used as a tension member, with one gage line of 3/4-in Ø bolts
in each leg at the usual gage location (see Table 3.1). What is the minimum amount of
stagger, s, necessary so that only one bolt need be subtracted from the gross area of the
angle? Compute the net area of this member if the lines of holes are staggered at 3 in.
(Ans. s = 4.77 in, A, = 5.05 in?)

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

This is a popular solution!

SEE SOLUTION Check out a sample Q&A here

Step 1

VIEW

Step 2

VIEW

Trending now

This is a popular solution!

Step by step

Solved in 2 steps with 3 images

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, civil-engineering and related others by exploring similar questions and additional content below.

Similar questions

An L8 × 4 × 3/4 with two lines of 3/4-in Ø bolts in the long leg and one line of 3/4-in Ø bolts in the short leg. Compute the net area of each of the given members. (Ans. 6.52 in^2)
An is used as a tension member, with 7/8-in Ø bolts in each leg atthe usual gage location (see Table 3.1). Two rows of bolts are used in the long leg,and one in the short leg. Determine the minimum stagger, s, necessary so that onlytwo holes need be subtracted in determining the net area. What is the net area?
An L8 x 4 x 3/4 is used as a tension member, with 7/8-in Ø bolts in each leg at the usual gage location . Two rows of bolts are used in the long leg, and one in the short leg. Determine the minimum stagger, s, necessary so that only two holes need be subtracted in determining the net area.What is the net area?
A W18 × 35 with two holes in each flange and one in the web, all for 7/8-in Ø bolts. Compute the net area of each of the given members. (Ans. 8.30 in^2)
An L 175 x 175 x 20 is used a tension member, with one gage line of 22 mm bolts in each leg at the usual gage location (where g=100 mm). What is the minimum amount of stagger, "s", necessary so that only one bolt need be subtracted from the gross area of the angle? Compute the net area of this member if the lines of holes are staggered at 90 mm.
The W24x76 beam has holes for 11/2in diameter bolts in the top and bottom flanges as shown. Determine the net area (An)at section A-A.
An L 150 x 100 x 16 is used as a tension member, with one gage line of 20 mm bolts in each leg at the usual gage location (Table3.1, where g=60 mm, g1=55 mm, and g2=60mm). Two rows of bolts are used in the long leg, and one in the short leg. What is the net area of the given steel connection? Stagger, s=58.63mm (Key Answer: An=3,008.00 mm)
An L 175 x 175 x 20 is used a tension member, with one gage line of 22 mm bolts in each leg at the usual gage location (where g=100 mm and s=134.20 mm). Compute the net area of this member if the lines of holes are staggered at 90 mm.
Compute the net area. The tension member shown in Figure P3-14 contains holes for 1-in Ø bolts.At what spacing, s, will the net area for the section through two holes be the same as a rupture line passing through all three holes?
An L 175 x 175 x 20 is used a tension member, with one gage line of 22 mm bolts in each leg at the usual gage location (where g=100 mm). What is the minimum amount of stagger, "s", necessary so that only one bolt need be subtracted from the gross area of the angle? (Key Answer: 134.20 mm)
Compute the net area. The 6 x 4 x 1/2 angle shown has one line of 1-in Ø bolts in each leg.The bolts are 4-in on center in each line and are staggered 2 in with respect to each other.
Compute the effective net area of the built-up section shown in Fig. P3-19 if the holes are punched for 3/4-in Ø bolts. Assume U = 0.90.