Isabelle pour 158cm^3 of glycerin, at a temperature of -12 °C, into a graduated cylinder initially at 19 °C, filling it to the very top. The cylinder is made of glass with a specific heat of 840 J/kg-K and a coefficient of volume expansion of 1.2 x10^−5 K^−1 ; its mass is 0.110kg. The mass of the glycerin is 0.0873 kg. What will be the final temperature of the glycerin, once thermal equilibrium is reached?

Isabelle pour 158cm^3 of glycerin, at a temperature of -12 °C, into a graduated cylinder initially at 19 °C, filling it to the very top. The cylinder is made of glass with a specific heat of 840 J/kg-K and a coefficient of volume expansion of 1.2 x10^−5 K^−1 ; its mass is 0.110kg. The mass of the glycerin is 0.0873 kg. What will be the final temperature of the glycerin, once thermal equilibrium is reached?

Principles of Heat Transfer (Activate Learning with these NEW titles from Engineering!)

8th Edition

ISBN:9781305387102

Author:Kreith, Frank; Manglik, Raj M.

Publisher:Kreith, Frank; Manglik, Raj M.

Chapter6: Forced Convection Over Exterior Surfaces

Section: Chapter Questions

Problem 6.12P

See similar textbooks

Similar questions

A 4.5 in (inside diameter), 4.9 in (outside diameter) tube carries dry saturated steam at 10 bar. Assume that the interior temperature of the tube is the same as that of the steam. The outside air temperature is 25°C. For ksteel = 51.9 W/(m K) and hair = 13.0 W/(m2K). a) How much energy is lost, in kWh, in a 20 m long section of pipe during an 8-hours
a) In a simple experiment, a solid with a diameter 3 mm and density 1500 kg/m3is released from a tall tower containing air at 25 oC and 1 atm. The inside diameter of the column is 0.15 m. The density of the air is assumed to be 1.2 kg/m3. List all your assumptions and estimate the minimum height of the tower to make sure the particle reaches its terminal velocity before it hits the bottom of the tower. b) In another experiment, 5 kg of the solid particles are to be fluidized with air at 1 atm and 25 oC. The diameter and density of the particles are 3 mm and 95 kg/m3, respectively.Using the Ergun Equation, determine whether the flow of the air is laminar orturbulent. List all your assumptions.
Question : Determine the units of the quantity s ̄/Ru, where s ̄ is the molar specific entropy and Ru is the universal gas constant. Explain your answer please
Steam (water vapor) enters a stainless steel tube with inner diameter 4cm at 300°C and 60 bar absolute pressure, with a velocity of 8.00 m/s. The steam exits the tube at 300°C and 40 bar absolute pressure. a. Assuming the water vapor behaves as an ideal gas, calculate the steam mass flow rate and the change in kinetic energy (in Watts). b. Using the specific volume values from table B.7, calculate the steam mass flow rate and the change in kinetic energy (in Watts).
It is observed that water at 20°C rises up to 20 m height in a tree due to capillary effect. The surface tension of water at 20°C is ?s = 0.073 N/m and the contact angle is 20°. The maximum diameter of the tube in which water rises is (a) 0.035 mm (b) 0.016 mm (c) 0.02 mm (d) 0.002 mm (e) 0.0014 mm
Steam is used to heat a cylindrical open tank of water until it boils, after which a proportion of the water in the tank is vaporised. The tank has an internal diameter of 1 m and is initially filled with water to a depth of 2 m. At the start of the process, this water is at 19°C and has a density of 998 kg/m3 . It may be assumed that ambient atmospheric pressure is 1 bar and that any effects arising from hydrostatic head can be ignored, as can heat losses from the tank to the surrounding environment. The heating medium is saturated steam at 5 bar, which enters a heating coil at the base of the tank at 5 kg/min, loses heat to the water in the tank and condenses to form saturated liquid condensate at this pressure. Using the steam table supplied: a) Find the temperature (°C) and power rating (kW) of the heater coil. b) Find the boiling point of the water in the tank under these conditions, and the time required to bring the water to this temperature. c) Find the proportion of water…
A long 8-cm diameter vertical steam pipe whose external surface temperature is 90 degrees C passes through some open area that is not protected against the wind blows. Determine the rate of heat loss from the pipe per unit length when the air is at 1 atm, 7 degrees Celsius and the wind is blowing across the pipe at a velocity of 50 km/h. From Table A-1:Thermal conductivity, k = 0.0275 W/m degrees Celsius ,viscosity, v = 1.77 x 10^-5 m^2/sPrandtl no. Pr = 0.71
6 -Problem II - A volume of compressed air storage tank is 0.3m3, and the air pressure P1 in the tank is 1MP.. When a part of compressed air is used, the pressure P2 of the air in the tank decreases to 0.9 MPa. Set the room temperature at 20 ° C, calculate the mass of original air ml and the mass of residual air m2. Air gas constant Rg = 287.1 J/ (kg - K)). 21
What are extensive and intensive properties? What is an isolated system? What is a quasi-static process? What is a manometer? What are the two types of manometers? What is a thermocouple? What is zeroth law of thermodynamics? What is a dimension? A unit? What is mechanical equilibrium? chemical equilibrium? thermal equilibrium? Electrical equilibrium? What is thermodynamic equilibrium? What is the seebeck effect? What is the instrument used to measure emf? At what temperature does glass begins to soften?
Ten pound of CO2 per second with an initial temperature of 180 °F is allowed to expand with flow from a pressure of 6000 to 1000 mmHg gauge. At what process is work maximized? A. Isentropic B. Isochoric C. Isobaric D. Isothermal E. Polytropic (n=1.4)
The aluminum fuel tank (α = 23.8 x 10-6 m/moC) on a sailboat measures 40 cm by 50 cm by 75 cm. If it is filled with 10oC gasoline from an underground tank, how much fuel will leak out when the fuel and the tank return to 28oC ambient temperature?
A 5L rigid container contains Acetylene initially at gage pressure and temperature of 100 KPa and 300 K, respectively. Because of the leaks in the fittings of the vessel, the gage pressure dropped to 80KPaand the temperature decrease to 200K, determine the mass of the Acetylene that leaked out.