1- Nitrogen is stored in a large chamber under conditions of 450 K and 1.5 x 105 N/m. The gas leaves the chamber through a convergent-only nozzle whose outlet area is 30 cm .The ambient room pressure is 1 × 105 N/m, and there are no losses. (a) What is the velocity of the nitrogen at the nozzle exit? (b) What is the mass flow rate? (c) What is the maximum flow rate that could be obtained by lowering the ambient pressure? ERING

1- Nitrogen is stored in a large chamber under conditions of 450 K and 1.5 x 105 N/m. The gas leaves the chamber through a convergent-only nozzle whose outlet area is 30 cm .The ambient room pressure is 1 × 105 N/m, and there are no losses. (a) What is the velocity of the nitrogen at the nozzle exit? (b) What is the mass flow rate? (c) What is the maximum flow rate that could be obtained by lowering the ambient pressure? ERING

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

A fan is used to transport CO2 gas (MW = 44 g/mol) gas at rest @ 700mmHg. At the discharge end, the pressure is 765mmHg, and the velocity is 100 m/s. Assuming the flue gas behaves ideally, and the process is isothermal, with the temperature maintained at 100C. Determine the theo. power required to move 45000 m /h of the flue gas.
Air fl ows adiabatically in a 3-cm-diameter duct, withf 5 0.018. At the entrance, T1 = 323 K, p1 =200 kPa, andV1 = 72 m/s. (a) What is the mass fl ow? (b) For what tubelength will the fl ow choke? (c) If the tube length is increasedto 112 m, with the same inlet pressure and temperature,what will be the new mass fl ow?
Air flows into a turbine at a rate 30 [m 3 /s], a temperature of 1100 [K] anda pressure of 300 [kPa]. The turbine’s work output is 200 [kJ/kg]. Determine thetemperature of the air at the exit, the power output in [kW] and the isentropicefficiency. The pressure ratio of the turbine is 3. The specific gas constant, R, for airis 0.287 [kJ/kg-K].
Nitrogen flows steadily through a converging tube. Near the inlet, the nitrogen is at 8.0 psia, 40 °F with a density of 0.0423 lbm/ft3 and has a velocity of 1600 ft/s through a cross sectional area of 0.40 sq. ft. At a section farther stream, the calculated density is 0.0225 lbm/ft3 and velocity is 1 300 ft/s. Determine the cross section at the downstream section.
A handheld bicycle pump can be used as an atomizer to generate a fine mist of paint or pesticide by forcing air at a high velocity through a small hole and placing a short tubebetween the liquid reservoir and the high-speed air jet whose low pressure drives the liquid up through the tube. In such an atomizer, the hole diameter is 0.3 cm, the vertical distance between the liquid level in the tube and the hole is 10 cm, and the bore (diameter) and the stroke of the air pump are 5 cm and 20 cm, respectively. If the atmospheric conditions are 20°C and 95 kPa, determine the minimum speed that the piston must be moved in the cylinder during pumping to initiate the atomizing effect. The liquid reservoir is open to the atmosphere
A gas flows steadily through a rotary compressor at a temperature of 16 ⁰C, a pressure of 100kPa, and an enthalpy of 392.2 kJkg-1. The gas leaves the compressor at a temperature of 245⁰C, a pressure of 0.6 MPa and an enthalpy of 534.5 kJkg-1. There is no heat transfer to or fromthe gas as it flows through the compressor. Using the steady flow equation appropriate toeach case, evaluate the external work done per unit mass of gas: a) when the inlet and exit velocities of the gas are negligible b) when the inlet velocity of the gas is 80 ms-1 and the exit velocity of the gas is 160 ms-1.
Air enters a fan through a duct velocity of 6.3 m/s and an inlet static pressure of 2.5cm of water less than the atmospheric pressure. The air leaves the fan through the duct at a velocity of 11.25 m/s and a discharge pressure of 7.62cm of water above the atmospheric pressure. If, the density of the air is 1.2kg/m3and the fan delivers 9.45m3/s, what is the fan efficiency when the power input to the fan is 13.75 kW at the coupling. Show schematic diagram and provide solutions.
The impeller of a centrifugal blower has a radius of 18 cm and a blade width of 6.1 cm at the inlet, and a radius of 30 cm and a blade width of 3.4 cm at the outlet. The blower delivers atmospheric air at 20°C and 95 kPa. Disregarding any losses and assuming the tangential components of air velocity at the inlet and the outlet to be equal to the impeller velocity at respective locations, determine the volumetric flow rate of air when the rotational speed of the shaft is 900 rpm and the power consumption of the blower is 120 W. Also determine the normal components of velocity at the inlet and outlet of the impeller.
How does the Bernoulli’s Theorem Apparatus show the relationship between the kinetic and potential heads during flow?
Consider steam at 500 K and 200 kPa. Estimate its speed ofsound by two different methods: (a) assuming an ideal gasfrom Table B.4, or (b) using finite differences for isentropicdensities between 210 kPa and 190 kPa.
The environmental conditions of a nozzle are required to provide 100 kPa, 20 C values and R-134a constant flow at 200 m / s. Bowl efficiency can be accepted as 90 percent. What should be the pressure and temperature at the nozzle entrance?
Air at 29oC with a rate of 0.03 kg/s enters a circularpipethat is constructedunderthewater. Thewatertemperature is kept at 17oC andconvectioncoefficientforwater is hw= 1500 W/m2.K Pipeproperties k=0.15 W/m.K Do=17cm Di=15cm a) Inordertoreach an airoutlettemperature of 21oC determinethereguiredpipelength b) What is required fan powertomovetheairthroughthepipe?