EXPERIMENT 2 – SIMULATION OF COMPRESSOR I want a perfect discussion and analysis of this result and discuss what is the effect of efficiency on compressor temperature and duty. Observations (when input (Natural gas) temperature= 150 °C):Mass flow rateof gas, kg/hrOutlet Temp. withadiabatic efficiency75%, °COutlet Temp. withadiabatic efficiency20%, °C6767197.4308203.360Observations (when input (Natural gas) temperature= 325 °C):Mass flow rateof gas, kg/hrOutlet Temp. withadiabatic efficiency75%, °COutlet Temp. withadiabatic efficiency20%, °C6767376.7504.4Compressor duty, kW75%20%762.601Compressor duty, kW75%20%1082.14288.570 NaturalgascompoutCompressorwork

A compressor is a device that reduces the volume of a material (typically a gas) to raise its…

Answered: iscuss what is the effect of efficiency…

Engineering

Mechanical Engineering

iscuss what is the effect of efficiency on compressor temperature and duty.

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Related questions

Q: Calculate the moments of inertia of the shaded area about the x- and y-axes. 46 27 46 27 -3535…

Q: A mechanism carries a constant load P applied to the seat as E shown. Calculate the forces, in…

A: Forces in mechanisms can be calculated by balancing them in particular directions. The sum of all…

Q: Determine the density of liquid whose specific gravity is 1.2

A: Given data : Density of water=ρW Specific gravity=S.G Required : Density of liquid

Q: HW Q1) Knowing that the coefficient of friction between the 25-kg block and the incline is μ = 0.25,…

Q: Consider a 150-MW steam power plant that operates on a simple Rankine cycle. Steam enters the…

Q: Find the efficiency of engine

A: Given: Input Power = 1000J Output Power= 200J To find: Efficiency (η)

Q: team flowing at a rate of 10 kg/h enters a steam turbine at a velocity of 50 m/s and leaves

Q: 2. Two 10-in 15.3-lb channels are welded together as shown in the figure. Compute the value of Ix.…

Q: For the setup shown in the figure, what is the pressure pa if the specific gravity of the oil is…

Q: A 80-mm diameter plunger is being pushed at 14 mm/sec into a tank filled with oil having sp. gr. of…

A: The oil that is being forced out is 0.3383 N/s.

Q: 1)Determine that the plane of the magnitude of W in the 200-1b body will have an 4.025 ft/sec2 AINL…

A: The change in the position of a body due to a force in a unit time is known as the velocity of that…

Q: R14-6. The 50-lb load is hoisted by the pulley system and motor M. If the motor exerts a constant…

A: Load, W= 50 lb Constant force on the cable, T= 30 lb s= 10 ft starting from the rest (Given that the…

Q: Hw/find the transfer function wher S S G₁ = 1 , G2 = G3 = J S +1 S +1 5² +2 H₁= 1 H₂ = S, H3 = 3 >…

Q: An airfoil at a given altitude has a critical Mach number of 0.7. Find the sweep angle that required…

A: Given Critical Mach number of airfoil, Mairfoil = 0.7 Mach…

Q: Determine the absolute maximum shear stress for each of the following plane stress states for which…

A: INTRODUCTION : The primary stresses are the greatest and minimum normal stresses, respectively. The…

Q: A 2-oz bullet is fired horizontally with a velocity v = 1000 ft/sec into the slender bar of a 3-lb…

Q: Determine the value of displacement Force applied on wooden box=12 N Work done=24J

A: displacement = 2 m

Q: Pa. Determine the COP of the cycle, if the e ic 275 kJ/kg

A: To determine COP of the cycle

Q: 2. For the beam shown: a. Draw the free-body diagram of the beam. b. Determine the reactions at the…

Q: An airfoil at a given altitude has a critical Mach number of 0.7. Find the sweep angle that is…

Q: The blade shown in the figure below is 1 ft wide and is intended to skim oil (SG = 0.9) floating on…

Q: The hydraulic cylinder imparts a constant upward velocity VA = 0.27 m/s to corner A of the…

Q: A fan draws air at rest and propels it 45 meters through a rectangular duct measuring 200 by 300 mm.…

A: L=45m

Q: Determine the value of displacement Force applied on wooden box=12 N Work done=24 J

A: Force applied on wooden box, F= 12 N Work done, W= 24 J To find: Displacement, "d"

Q: The engine mechanism shown in the figure below has crank OB = 50 mm and length of connecting rod AB…

Q: Where to put marker for maximum steady state force. It is F-t graph.

A: Concept: Steady state means the graph line looks almost constant with zero slope and it is parallel…

Q: F9-6. The beam is subjected to the loading shown. Determine the principal stress at point C. 75 mm C…

Q: Determine the coordinates of the centroid of the trapezoidal area shown. Assume a = 245 mm, b = 465…

Q: A boiler furnace releases 10 400 kj of heat for each kg of fuel burned and produces dry staturated…

A: A boiler is a closed vessel that is used to heat water or another fluid under pressure. After that,…

Q: 1. Calculate the corrosion rate (in mm/yr and mpy) for iron in an acid if the iron loss is 0.01 gms…

Q: Failure of Materials Due to Creep and Fatigue.

A: Environmental conditions, such as corrosion, have an impact on fatigue strength. The fatigue…

Q: 3. When subcooling the liquid refrigerant: a. the refrigerating effect per unit mass increases. b.…

A: Subcooling within a vapor-compression refrigeration cycle has the following effect: It increases…

Q: A four-cylinder, four-stroke internal combustion engine operates at 2800 RPM. The processes within…

A: Given data Speed = N = 2800 rpmP1 = 14.7 lbf/in2 = 101352.932 PaT1 = 80°F = 299.8167 KV1 = 0.03 ft3…

Q: 8 Air enters an ideal (reversible, adiabatic) turbine at 200 psia and 1000°F and exits at 14.7 psia.…

A: Given data, Adiabatic Reversible process INLET: P1 = 200 psia T1 = 1000°F = 810.928 K EXIT: P2 =…

Q: F6-13. If the beam is subjected to a bending moment of M = 5 kN m, determine the bending stress…

A: The bending stress developed at point A is 1.98 MPa.

Q: equired to obtain a critical Mach number of 0.9 at the same altitude.

A: Given Critical Mach number of airfoil, Mairfoil = 0.7 Mach…

Q: Air enters a two-stage compressor operating at steady state at 520°R, 14 lbf/in.2 The overall…

A: A compressor that compresses air in two stages is known as a two-stage compressor. The fluid…

Q: The given frame is subjected to the applied loads P and Q. Note that members ABC and CDE are…

Q: Urgent 3D model design for this vehicle body (4 passengers / 4 chairs if possible)

A: Given question : Design a 3D model for the given dimensions.

Q: 2. An electron is moving with a speed of 5 x 107m/s at right angle to a magnetic field of 5000 G.…

Q: Q/ Draw a Top view with the dimensions written on it 10 -20 20 2010 -20 Top View?? 50 10 -30 10…

A: To draw the top view, project all the lines from front view and side view on the box shown. Thicken…

Q: An extruded polymer beam is subjected to a bending moment M. The length of the beam is L = 620 mm.…

A: Find the largest moment .

Q: A heat recovery device involves transferring energy from the hot flue gases passing through an…

Q: What is the minimum diameter of a solid steel shaft that will not twist through more than 4o in a 9…

A: Given data : Angle of twist θ=4∘ Length L=9 m Torque T=11 KN×m Modulus of rigidity G=83 GPa

Q: An airfoil at a given altitude has a critical Mach number of 0.7. Find the sweep angle that is…

Q: A beam is supported and loaded as shown. In the section of the beam between 'A' and 'B', the…

Q: stiffness introduced to the loudspeaker if it is mounted in an enclosed cabinet with an internal…

Q: A part of the structure for a facory automation system is a beam that spans 30.0 inches as shown…

Q: 1. Determine the pressure acting on the upper and lower surfaces of a flat plate inclined at a 12°…

Q: Water at 60°F is pumped from a reservoir to the top of a mountain through a 6-in. Schedule 120 pipe…

Question

EXPERIMENT 2 – SIMULATION OF COMPRESSOR

I want a perfect discussion and analysis of this result and discuss what is the effect of efficiency on compressor temperature and duty.

Observations (when input (Natural gas) temperature= 150 °C):
Mass flow rate
of gas, kg/hr
Outlet Temp. with
adiabatic efficiency
75%, °C
Outlet Temp. with
adiabatic efficiency
20%, °C
6767
197.4
308
203.360
Observations (when input (Natural gas) temperature= 325 °C):
Mass flow rate
of gas, kg/hr
Outlet Temp. with
adiabatic efficiency
75%, °C
Outlet Temp. with
adiabatic efficiency
20%, °C
6767
376.7
504.4
Compressor duty, kW
75%
20%
762.601
Compressor duty, kW
75%
20%
1082.14
288.570

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

SEE SOLUTION Check out a sample Q&A here

Step 1: Introduction

VIEW

Step 2: Explanation

VIEW

Step by step

Solved in 2 steps

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, mechanical-engineering and related others by exploring similar questions and additional content below.

Similar questions

The value of enthalpy at point 1 is ( hi2 ?) The value of enthalpy at point 3 is (h3?) The value of enthalpy at point 4 is (h4?) The value of steam mass flow rate in kg/s is The rate of heat supplied is
What is the ideal mass flow rate for a refrigeration and cryogenic plant for oxygen production? Show solution if necessary and reference.
A 400-L tank, A contains argon gas at 250 kPa, 30°C. Cylinder B, having a frictionless piston of such mass that a pressure of 150 kPa will float it, is initially empty. The valve is opened and argon flows into B and eventually reaches a uniform state of 150 kPa, 30°C throughout. What is the work done by the argon?
When saturated liquid at 40degree C is throttled to -20 degree C the quality at exit will be ?
Pls explain if the value of ideal gas R is included
Nitrogen is contained in a 80L tank and the initial pressure andtemperature is 250 kPa and 200 °C, respectively. Note the ideal gasconstant for nitrogen is 0.2968 kJ/kg K Determine: The mass of the gas in kg. Now, if 0.05 kg of gas leaks out of the tank and in the process thetemperature drops to 33 °C. Find the gage pressure of the gasremaining in the tank in kPa. If the atmospheric pressure is 101.325kPa.
Q5. What is the change in enthalpy (in Btu/lb) of carbon dioxide gas if the change in internal energy is 100 Btu/lb?
Determine the entropy, Salpha (T,P)
In an absorption chiller, ____________ is used to createthe difference in pressures.
Using the Steam Table shown, at initial pressure of 0.046 bar and final pressure of 0.107 bar, find the following: Δhf ; Δhg ; Δsf ; Δsg
An ideal gas initially at one atmosphere is ___ (?) reversibly to two atmosphere while in thermal contact with the surroundings. Calculate the heat Q, Qsurr, delta S and delta S univ for the process.
A furnace heats water at a saturated state with a pressure of 1 bar. How much heat is given When the water condition in the tank is 15 bar and 500°C. Specify: a) Heat needed? b) Internal changes in energy? c) Work done?