A distance between points A and B is measured and recorded as 123.456 meters using a tape that has a certifiedlength of 29.992 meters. What is the true distance between A and B?a. 123.486 mb. 123.448 ma.b.C.dA 50-m tape weighing 1.075 kg has a standard pull of 8 kg. The tap's cross-sectional area and modulus of elasticity are0.05 cm² and 200 GPa, respectively. What (normal tension) is required in order that the effect of sag will be eliminatedwhen the tape is supported at end points only?247.5 N197.4 Na 0.25%b. 0.26%123.489 m123.423 mCdi163.6 N327.9 NDetermine the percentage uncertainty in the area of a square that is 6.08 ± 0.01 m on a side.C.0.29%d.0.33%

Answered: Image /qna-images/answer/a51a372f-38cc-4842-99f7-4737c00655d0.jpg

Istance between points A and B is measured and recorded as 123.456 meters using a tape that has a certified gth of 29.992 meters. What is the true distance between A and B? 123.486 m 123.448 m 123.489 m 123.423 m 0-m tape weighing 1.075 kg has a standard pull of 8 kg. The tap's cross-sectional area and modulus of elasticity ar C. d.

Istance between points A and B is measured and recorded as 123.456 meters using a tape that has a certified gth of 29.992 meters. What is the true distance between A and B? 123.486 m 123.448 m 123.489 m 123.423 m 0-m tape weighing 1.075 kg has a standard pull of 8 kg. The tap's cross-sectional area and modulus of elasticity ar C. d.

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

Distance is measured as 605.75m with a 50-m tape supported on quarters with a pull of 6.5kg. The standard pull of the tape is 5.2kg; its weight is 1.10kg, E=2.02x10^6 kg/sqcm, and the unit weight is 0.03kg/cubic cm. a. What is the correction due to tension? b. What is the total correction due to sag? c. What is the corrected length?
A line was found to be 2,395.25 m long when measured with a 30 m tape under a steady pull of 3 kg. at a mean temperature of 30°C. The tape was held in the air and supported at both ends and at every one third of the tape. Determine the correct length of the line if the tape used is of standard length at 20°C under a pull of 5 kg. Assume the cross-sectional area of tape to be 0.02 cm2, Elastic Modulus as 2.10 x 106kg/cm2, weighs 0.05 kg/m, and a Coefficient of Thermal Expansion to be 0.0000116/°C.
A 50-m steel tape is of standard length under a pull of 55 N and a temperature of 20°C when supported throughout its entire length. The tape weighs 0.055kg/m, has a cross sectional area of 0.04 cm² and a modulus of elasticity of 2x10⁶ kg/cm². This tape was used in the field to measure a distance that was determined to be 501.650 m. At the time the measurement was made, the constant pull applied was 80 N with the tape supported only at endpoints. During the measurement the temperature was observed to be at an average of 18°C. Use a = 11.6x10-6 m/"C a. Determine the correction due to tension. b. Determine the correction due to change in temperature. C. Determine the correction due to sag. d. Determine the correct length of the line.
A 50-m steel tape is of standard length under a pull of 55 N and a temperature of 20°C when supported throughout its entire length. The tape weighs 0.055kg/m, has a cross sectional area of 0.04 cm² and a modulus of elasticity of 2x106 kg/cm². This tape was used in the field to measure a distance that was determined to be 501.650 m. At the time the measurement was made, the constant pull applied was 80 N with the tape supported only at endpoints. During the measurement the temperature was observed to be at an average of 18°C. Use a = 11.6x10-6 m/" a Determine the correction due to tension. b. Determine the correction due to change in temperature. C. Determine the correction due to sag. d. Determine the correct length of the line.
Problem 3. A 50-m steel tape is of standard length under a pull of 55 N and a temperature of 20°C when supported throughout its entire length. The tape weighs 0.055kg/m, has a cross sectional area of 0.04 cm² and a modulus of elasticity of 2x106 kg/cm². This tape was used in the field to measure a distance that was determined to be 501.650 m. At the time the measurement was made, the constant pull applied was 95 N with the tape supported all throughout. During the measurement the temperature was observed to be at an average of 30°C. Use a = 11.6x10-6 m/°C. Determine the correct length of the line.
A 50 m steel tape is used to measure a rectangle at 20°C with a pull of 55 N. The sides are recorded as 155.90 m and 121.00 m. The average temperature during measurement is 30°C with a pull of 55 N. C = 0.0000116/°C. Compute the total corection for the length.
A 30 m tape steel tape weighing 0.7 kg has a cross-sectional area of 0.03cm² and a standard length of 30.005m when fully supported at 20°C, and with 5 kg tension. A line on a smooth level ground is measured with the tape under the tension of 10 kg at a temperature of 20°C and is recorded as 1242.823 m long. Compute the correction for the increase in tension. K = 2 100 000 kg /cm². This same tape is used to measure a distance recorded as 985.423 m over level terrain with the tape supported at the two ends and 5kg of tension (temperature of 20°C). Calculate the correction due to sag for this distance.
The taped distance of a line is 86.67 meters using a 100 m. steel tape at a pull of 20 kg and temperature a 32°C. The tape is exactly 100 m. at a temperature of 28°C (supported throughout) and standard pull of 10 kg. If the coefficient of expansion of the tape is 0.00001 18, find the total correction for temperature.
A 50-m steel tape is of standard length under a pull of 5.50 kg and a temperature of 20°C when supported throughout its entire length. The tape weighing 0.05 kg/m, has a cross sectional area of 0.04cm2 and a modulus of elasticity of 2x106 kg/cm2. This tape was used in the field to measure a distance that was determined to be 458.65m. At the time the measurement was made, a constant pull of 8kg was applied with the tape supported at endpoints only. During the measurement, it was a cool atmosphere at an average temperature of 18°C. Determine the correct length of the line.
The measured distance of two locations is 88.812 m using a 100 m. steel tape at a pull of 15 kg and temperature of 35 °C. The tape is exactly 100 m., weighing 0.02 kg/m, at a temperature of 20 °C (when supported throughout) and a standard pull of 12 kg. If the coefficient of expansion of the tape is 11.6 x10°/°€ and supported at L. = 40 m. interval during the measurement, find the following: a.) Total correction tor temperature b.) Total sum of correetion for sag from 0 to 88.812 m at 40 m interval. c.) Adjusted distance
A 50-m steel tape is of standard length under a pull of 5.5 kg when supported throughout its entire length. The tape weighs 0.05 kg/m, has a cross-sectional area of 0.04 sq. cm., and being made of steel, its modulus elasticity is 2.10x10^6 kg/cm2. This tape was used in the field to measure a distance that was determined to be 458.650 m. At the time thr measurement was made, the constant pull applied was 8 kg with the tape supported only at its end points. Determine the correct length of the line.
A tape 100m long, it's cross sectional area in 0.0585 cm', the apparent length of which was found to be 1500m. The tape was Standardized under a pull of 6.75kg but after the line was measured, it was Found that the pull actually used during the measurement was = 7.75 kg. what Was the true length of the line if the tape was standardized & used on the flat? Take young modulus, E = 2,000,000 kg/cm²